OPEL COMBO-D Owner's Manual Contents Introduction .................................... 2 In brief ............................................ 6 Keys, doors and windows ............ 19 Seats, restraints ........................... 32 Storage ........................................ 49 Instruments and controls ............. 57 Lighting ........................................ 83 Climate control ............................. 89 Driving and operating ................... 95 Vehicle care ............................... 118 Service and maintenance .......... 151 Technical data ........................... 154 Customer information ................ 170 Index .......................................... 172 2 Introduction Introduction Introduction Vehicle specific data Please enter your vehicle's data on the previous page to keep it easily accessible. This information is available in the sections "Service and maintenance" and "Technical data" as well as on the identification plate. Introduction Your vehicle is a designed combination of advanced technology, safety, environmental friendliness and economy. This Owner's Manual provides you with all the necessary information to enable you to drive your vehicle safely and efficiently. Make sure your passengers are aware of the possible risk of accident and injury which may result from improper use of the vehicle. You must always comply with the specific laws and regulations of the country that you are in. These laws may differ from the information in this Owner's Manual. When this Owner's Manual refers to a workshop visit, we recommend your Opel Service Partner. All Opel Service Partners provide first-class service at reasonable prices. Experienced mechanics trained by Opel work according to specific Opel instructions. The customer literature pack should always be kept ready to hand in the vehicle. Using this manual ■ This manual describes all options and features available for this model. Certain descriptions, including those for display and menu functions, may not apply to your vehicle due to model variant, country specifications, special equipment or accessories. ■ The "In brief" section will give you an initial overview. ■ The table of contents at the beginning of this manual and within each section shows where the information is located. 3 ■ The index will enable you to search for specific information. ■ This Owner's Manual depicts lefthand drive vehicles. Operation is similar for right-hand drive vehicles. ■ The Owner's Manual uses the factory engine designations. The corresponding sales designations can be found in the section "Technical data". ■ Directional data, e.g. left or right, or front or back, always relate to the direction of travel. ■ The vehicle display screens may not support your specific language. ■ Display messages and interior labelling are written in bold letters. Danger, Warnings and Cautions 9 Danger Text marked 9 Danger provides information on risk of fatal injury. Disregarding this information may endanger life. 4 Introduction 9 Warning Text marked 9 Warning provides information on risk of accident or injury. Disregarding this information may lead to injury. Caution Text marked Caution provides information on possible damage to the vehicle. Disregarding this information may lead to vehicle damage. Symbols Page references are indicated with 3. 3 means "see page". We wish you many hours of pleasurable driving. Adam Opel AG Introduction 5 6 In brief In brief Vehicle unlocking Unlocking with key Unlocking with radio remote control Initial drive information Turn the key in the driver's door lock towards the front of the vehicle. Press button Ä to unlock the doors and load compartment. Open the doors by pulling the handles. To open the tailgate, press the button under the tailgate handle. Press button Å; only the load compartment is unlocked. Radio remote control 3 19, Central locking system 3 20, Load compartment 3 24, Power windows 3 28. In brief Seat adjustment Seat backrests Seat height Turn handwheel. Do not lean on backrest when adjusting. Seat position 3 33, Seat adjustment 3 33. Lever pumping motion up = higher down = lower 7 Seat positioning Pull handle, slide seat, release handle. Seat position 3 33, Seat adjustment 3 33. 9 Danger Do not sit nearer than 25 cm from the steering wheel, to permit safe airbag deployment. Operate lever and adjust body weight on seat to raise or lower it. Seat position 3 33, Seat adjustment 3 33. 8 In brief Head restraint adjustment Seat belt Mirror adjustment Interior mirror Press release catch, adjust height, engage. Head restraints 3 32. Pull out the seat belt and engage in belt buckle. The seat belt must not be twisted and must fit close against the body. The backrest must not be tilted back too far (maximum approx. 25 °). To release belt, press red button on belt buckle. Seat position 3 33, Seat belts 3 37, Airbag system 3 40. Adjust the lever on the underside to reduce dazzle. Interior mirror 3 28. In brief Steering wheel adjustment Exterior mirrors Swivel lever in required direction. 9 Select the relevant exterior mirror by turning the control to left _ or right 6. Then swivel the control to adjust the mirror. In position o no mirror is selected. Convex exterior mirrors 3 26, Electric adjustment 3 27, Folding exterior mirrors 3 27, Heated exterior mirrors 3 27. Unlock the lever, adjust the steering wheel, then engage lever and ensure it is fully locked. Do not adjust steering wheel unless vehicle is stationary and the steering wheel lock has been released. Airbag system 3 40, Ignition positions 3 96. 10 In brief Instrument panel overview In brief 1 2 3 Fixed air vents ....................... 93 Side air vents ........................ 92 Light switch .......................... 83 4 Turn and lane-change signals, headlight flash, low beam and high beam ..... 85 Instruments .......................... 63 5 Driver Information Centre ...... 74 Windscreen wiper, windscreen washer system, rear wiper ................ 58 6 7 Trip reset ............................... 63 Centre air vents .................... 92 Headlight range adjustment ........................... 84 Front fog lights ..................... 85 Rear fog light ........................ 86 Trip computer ........................ 81 8 Front passenger airbag ........ 41 9 Glovebox .............................. 50 10 Climate control system .......... 89 11 Selector lever, manual transmission ....................... 101 Manual transmission automated ........................... 101 12 Ignition switch with steering wheel lock .............. 96 13 Steering wheel controls ....... 57 14 Horn ..................................... 58 15 16 17 18 Driver airbag ........................ 41 Steering wheel adjustment . . 57 Cruise control ..................... 108 Fuse box ............................. 133 Bonnet release lever .......... 120 11 12 In brief In brief Exterior lighting Fog lights Turn light switch 8 = sidelights 9 = headlights Press light switch > = front fog lights r = rear fog light Lighting 3 83. 13 Headlight flash, high beam and low beam headlight flash = pull lever high beam = push lever low beam = pull lever High beam 3 83, Headlight flash 3 83. 14 In brief Turn and lane-change signals Hazard warning flashers Horn lever up = right turn signal lever down = left turn signal Operated with the ¨ button. Hazard warning flashers 3 85. Press j. Turn and lane-change signals 3 85. In brief Washer and wiper systems Windscreen wiper Twist lever: É = fast È = slow Ç = intermittent wiping = off § For a single wipe when the windscreen wiper is off, move the lever up. Windscreen wiper 3 58, Wiper blade replacement 3 124. 15 Windscreen and headlight washer systems Rear window wiper and washer systems Pull lever. Windscreen and headlight washer system 3 58, Washer fluid 3 122. Twist to activate the rear window wiper. The rear window wiper comes on automatically when the windscreen wiper is switched on and reverse gear is engaged. Push lever: Washer fluid is sprayed on the rear window and the wiper wipes a few times. Rear window wiper/washer 3 59. 16 In brief Climate control Heated rear window, heated exterior mirrors The heating is operated by pressing the Ü button. Heated rear window 3 30. Demisting and defrosting the windows Set the temperature control to V. Set fan to 4. Set air distribution control to V. Cooling n on. Heated rear window Ü on. Climate control system 3 89. Transmission Manual transmission Reverse: with the vehicle stationary, wait 3 seconds after depressing the clutch pedal, pull up the collar on the selector lever and engage the gear. If the gear does not engage, set the lever to neutral, release the clutch pedal and depress again; then repeat gear selection. Manual transmission 3 101. In brief Manual transmission automated Starting off 17 Starting the engine Check before starting off N o + A/M R = = = = = neutral position drive position higher gear lower gear switch between automatic and manual mode = reverse gear (with selector lever lock) Manual transmission automated 3 101. ■ Tyre pressure and condition 3 135, 3 167. ■ Engine oil level and fluid levels 3 120. ■ All windows, mirrors, exterior lighting and number plates are free from dirt, snow and ice and are operational. ■ Proper position of mirrors, seats, and seat belts 3 27, 3 33, 3 38. ■ Brake function at low speed, particularly if the brakes are wet. ■ Turn key to position MAR ■ move the steering wheel slightly to release the steering wheel lock ■ operate clutch and brake ■ do not operate accelerator pedal ■ diesel engines: turn the key to position MAR for preheating and wait until control indicator ! goes out ■ turn key to position AVV and release Starting the engine 3 96. 18 In brief Stop-start system Parking If the vehicle is at a low speed or at a standstill and certain conditions are fulfilled, activate an Autostop as follows: ■ Depress the clutch pedal ■ set the lever in neutral ■ release the clutch pedal An Autostop is indicated when ^ is displayed in the Driver Information Centre (DIC) 3 74. To restart the engine, depress the clutch pedal again. Stop-start system 3 97. ■ Always apply the parking brake. Activate the manual parking brake without pressing the release button. Apply as firmly as possible on a downhill slope or uphill slope. Depress foot brake at the same time to reduce operating force. ■ Switch off the engine. Turn the ignition key to position STOP and remove it. Turn the steering wheel until the steering wheel lock is felt to engage. ■ If the vehicle is on a level surface or uphill slope, engage first gear. On an uphill slope, turn the front wheels away from the kerb. If the vehicle is on a downhill slope, engage reverse gear. Turn the front wheels towards the kerb. ■ Lock the vehicle with button e on the radio remote control. ■ Do not park the vehicle on an easily ignitable surface. The high temperature of the exhaust system could ignite the surface. ■ Close the windows and the sunroof. ■ The engine cooling fans may run after the engine has been switched off 3 119. ■ After running at high engine speeds or with high engine loads, operate the engine briefly at a low load or run in neutral for approx. 30 seconds before switching off, in order to protect the turbocharger. Keys, locks 3 19, Laying the vehicle up for a long period of time 3 118. Keys, doors and windows Keys, doors and windows Keys, locks ................................... 19 Doors ........................................... 22 Vehicle security ............................ 25 Exterior mirrors ............................ 26 Interior mirrors ............................. 28 Windows ...................................... 28 Keys, locks Keys Replacement keys The key number is specified in the Car Pass or on a detachable tag. The key number must be quoted when ordering replacement keys as it is a component of the immobiliser system. Locks 3 147. Key with foldaway key section 19 Press button to extend. To fold the key, first press the button. Car Pass The Car Pass contains security related vehicle data and should therefore be kept in a safe place. When the vehicle is taken to a workshop, this vehicle data is needed in order to perform certain operations. Radio remote control 20 Keys, doors and windows Used to operate: ■ Central locking system 3 20 ■ Anti-theft locking system 3 25 ■ Power windows 3 28 The radio remote control has a range of up to 5 metres. It can be restricted by external influences. The hazard warning flashers confirm operation. Handle with care, protect from moisture and high temperatures and avoid unnecessary operation. ■ Overload of the central locking system by operating at frequent intervals, the power supply is interrupted for a short time ■ Interference from higher-power radio waves from other sources Unlocking 3 20. Radio remote control battery replacement Replace the battery as soon as the range reduces. Fault If the central locking system cannot be operated with the radio remote control, it may be due to the following: ■ Range exceeded ■ Battery voltage too low ■ Frequent, repeated operation of the radio remote control while not in range Key with foldaway key section Batteries do not belong in household waste. They must be disposed of at an appropriate recycling collection point. Extend the key and remove the battery holder by undoing the screw with a suitable screwdriver. Remove the battery holder from the key and replace the battery (type CR 2032), paying attention to the installation position. Refit the battery holder in the key and secure the screw. Central locking system Unlocks and locks doors and load compartment. Keys, doors and windows A pull on an interior door handle unlocks the entire vehicle and opens the respective door. Unlocking Depending on vehicle configuration. Press button Å: The load compartment (rear doors / tailgate and sliding side doors) are unlocked. Press button Ä: All doors, including rear doors / tailgate and sliding side doors are unlocked. Note In the event of an accident of a certain severity, the vehicle unlocks automatically. Fuel cut-off system 3 80. Note If engaged, the emergency lock on the sliding side door remains engaged even after unlocking the vehicle with the remote control. Emergency lock 3 22. Locking Close all doors. If the doors are not closed properly, the central locking system will not work. Press button e. Automatic locking The vehicle can be configured to automatically lock the doors when vehicle speed exceeds 20 km/h. Driver Information Centre (DIC) 3 74. 21 22 Keys, doors and windows Unlocking the load compartment from inside the vehicle Child locks 9 Warning Doors Sliding door Use the child locks whenever children are occupying the rear seats. Press button Å: The load compartment (rear doors / tailgate and sliding side doors) are unlocked. When the load compartment is locked, the LED in the button is illuminated. Pull lever on interior handle and slide door. Caution Using a key or suitable screwdriver, turn child lock switch on sliding side door to the horizontal position. The door cannot be opened from inside. To deactivate, turn the child lock switch to the vertical position. Ensure the side door is fully closed and secure before driving the vehicle. Central locking system 3 20. Keys, doors and windows Caution To avoid damage, do not attempt to operate the sliding side door when the fuel filler flap is open. Refuelling 3 113. Emergency lock Using a key or suitable screwdriver, turn the emergency lock switch on the sliding side door to locked position 1. The door cannot be opened from outside. The emergency lock remains engaged even after unlocking the vehicle with the remote control. To disengage, turn the switch to unlocked position 2. Rear doors To prevent the sliding side door from being opened from the outside, open the door and engage the emergency lock. 23 To open the left hand rear door pull the outside handle. The door is opened from inside the vehicle by pressing down the interior handle. 24 Keys, doors and windows The right hand rear door is released using the lever. 9 Warning The rear lights may be obscured if the rear doors are open and the vehicle is parked on the roadside. Make other road users aware of the vehicle, by using a warning triangle or other equipment specified in the road traffic regulations. The doors are retained in the 90º position by locking stays. To open the doors to 180º, push the latch and swing open to the desired position. 9 Warning Load compartment Tailgate Opening Ensure extended opening doors are secured when fully opened. Opened doors may slam closed due to the force of the wind! Always close the right hand door before the left hand door. Central locking system 3 20. Press the button underneath the moulding. 9 Warning Do not drive with the tailgate open or ajar, e.g. when transporting bulky objects, as toxic exhaust gases could enter the vehicle. Keys, doors and windows Caution Before opening the tailgate check overhead obstructions, such as a garage door, to avoid damage to the tailgate. Always check the moving area above and behind the tailgate. Note The installation of certain heavy accessories onto the tailgate may affect its ability to remain open. Closing Use the interior handle. Ensure tailgate is fully closed before driving. Central locking system 3 20. 25 Vehicle security Anti-theft locking system 9 Warning Do not use the system if there are people in the vehicle! The doors cannot be unlocked from the inside. The system deadlocks all the doors. All doors must be closed otherwise the system cannot be activated. The system is disabled automatically on every door when: ■ unlocking the doors ■ turning the ignition switch to MAR 26 Keys, doors and windows Activating If the control indicator d illuminates when starting, there is a fault in the system; the engine cannot be started. Switch off the ignition and repeat the start attempt. If d remains illuminated, attempt to start the engine using the spare key and seek the assistance of a workshop. Note The immobiliser does not lock the doors. Always lock the vehicle after leaving it 3 20. Press e on the radio remote control twice. Exterior mirrors Convex shape The convex exterior mirror contains an aspherical area and reduces blind spots. The shape of the mirror makes objects appear smaller, which will affect the ability to estimate distances. Manual adjustment Control indicator d 3 73. Immobiliser The system is part of the ignition switch and checks whether the vehicle is allowed to be started with the key being used. The immobiliser is activated automatically after the key has been removed from the ignition switch. Adjust mirrors by swivelling lever in required direction. The lower mirrors are not adjustable. Keys, doors and windows 27 Electric adjustment Folding Heated Select the relevant exterior mirror by turning the control to left _ or right 6. Then swivel the control to adjust the mirror. In position o no mirror is selected. For pedestrian safety, the exterior mirrors will swing out of their normal mounting position if they are struck with sufficient force. Reposition the mirror by applying slight pressure to the mirror housing. Operated by pressing the Ü button. Heating works with the engine running and is switched off automatically after a short time. 28 Keys, doors and windows Interior mirrors Windows Manual anti-dazzle Windscreen Windscreen stickers Do not attach stickers such as toll road stickers or similar on the windscreen in the area of the interior mirror. Keep a close watch on the windows when closing them. Ensure that nothing becomes trapped in them as they move. Switch on ignition to operate power windows. Manual windows The door windows can be opened or closed with the window winders. To reduce dazzle, adjust the lever on the underside of the mirror housing. Power windows 9 Warning Take care when operating the power windows. Risk of injury, particularly to children. If there are children on the rear seats, switch on the child safety system for the power windows. Operate the switch for the respective window by pushing to open or pulling to close. Pushing or pulling briefly: window moves up or down in stages if the switch is held. Keys, doors and windows Pushing or pulling firmly and then releasing: window moves up or down fully with safety function enabled. To stop movement, operate the switch once more in the same direction. With the ignition key removed or in the STOP position, the windows can be operated for approx. 2 minutes and are deactivated as soon as a door is opened. Safety function If the window glass encounters resistance during automatic closing, it is immediately stopped and opened again. If the safety function is activated five times in less than a minute, the safety function is deactivated. The windows will only close in stages and not automatically. Activate the window electronics by opening the windows. The safety function is restored and the windows will operate normally. Overload If the windows are repeatedly operated within short intervals, the window operation is disabled for some time. 29 Child safety system for rear windows Initialising the power windows If the windows cannot be closed automatically (e.g. after disconnecting the vehicle battery), activate the window electronics as follows: 1. Close doors. 2. Switch on ignition. 3. Pull switch until the window is closed and keep pulling for an additional 5 seconds. 4. Repeat for each window. Press switch , to deactivate rear door power windows. To activate, press , again. Operating windows from outside The windows can be operated remotely from outside the vehicle when locking or unlocking the vehicle. Central locking system 3 20. 30 Keys, doors and windows Rear windows Heated rear window Opening rear windows Press and hold the Ä button to open windows. Press and hold the e button to close windows. Release button to stop window movement. To open, move lever outwards until the window is fully open. To close, pull lever then push until window is fully closed. Operated by pressing the Ü button. Heating works with the engine running and is switched off automatically after a short time. Sun visors The sun visors can be folded down or swivelled to the side to prevent dazzling. If the sun visors have integral mirrors, the mirror covers should be closed when driving. Keys, doors and windows A ticket holder is located on the backside of the sun visor. 31 32 Seats, restraints Seats, restraints Head restraints ............................ 32 Front seats ................................... 33 Rear seats ................................... 35 Seat belts ..................................... 37 Airbag system .............................. 40 Child restraints ............................. 44 Head restraints Adjustment Head restraints on front seats Position 9 Warning Only drive with the head restraint set to the proper position. Height adjustment Press the button, adjust height and engage. The upper edge of the head restraint should be at upper head level. If this is not possible for extremely tall people, set to highest position, and set to lowest position for small people. Seats, restraints Head restraints on rear seats Front seats Seat position 9 Warning Only drive with the seat correctly adjusted. Height adjustment Pull the head restraint upwards or press the catch to release and push the head restraint downwards. Removal Press both catches, pull the head restraint upwards and remove. Note Approved accessories may only be attached if the seat is not in use. ■ Sit with buttocks as far back against the backrest as possible. Adjust the distance between the seat and the pedals so that legs are slightly angled when pressing the pedals. Slide the front passenger seat as far back as possible. 33 ■ Sit with shoulders as far back against the backrest as possible. Set the backrest to an angle so that it is possible to reach the steering wheel with arms slightly bent. Maintain contact between shoulders and the backrest when turning the steering wheel. Do not tilt the backrest too far back. We recommend a maximum angle of approx. 25°. ■ Adjust the steering wheel 3 57. ■ Set the seat high enough to have a clear field of vision on all sides and on all display instruments. There should be at least one hand of clearance between head and the roof frame. Thighs should rest lightly on the seat without pressing into it. ■ Adjust the head restraint 3 32. ■ Adjust the height of the seat belt 3 38. Seat adjustment Drive only with seats and backrests properly engaged. 34 Seats, restraints 9 Danger Seat backrests Seat height Turn handwheel. Do not lean on backrest when adjusting. Lever pumping motion up = higher down = lower Do not sit nearer than 25 cm from the steering wheel, to permit safe airbag deployment. 9 Warning Never adjust seats while driving as they could move uncontrollably. Seat positioning Operate lever and adjust body weight on seat to raise or lower it. Pull handle, slide seat, release handle. Seats, restraints Armrest Heating 35 Rear seats Third row seats 9 Warning Never adjust seats while driving as they could move uncontrollably. Folding the seats The load compartment area can be increased by folding up the rear seats. Raise or lower the armrest as required. Activate heating by pressing ß button for the seat with the ignition on. LED in button ß on: relevant front seat heating on. Prolonged use for people with sensitive skin is not recommended. 9 Warning When folding the seat use caution - beware of moving parts. Ensure the seat is secure when completely folded. ■ Lower the head restraint and move the seat belt to one side. ■ Remove the load compartment cover if necessary 3 51. 36 Seats, restraints ■ Pull the release lever and fold down the backrest onto the seat cushion. Pull the lower strap and fold the seat assembly forwards. ■ Secure the folded seat in the upright position by attaching the flexible cord located on the seat frame, to the rear seat head restraint. ■ To lower the seat, remove the flexible cord and lower the seat assembly to the floor, ensuring the rear support is located on the anchor point and securely latched. ■ Raise the backrest and adjust the head restraint. ■ The backrest is properly engaged when red mark on the release lever is no longer visible. Removing the seats ■ Remove the seat head restraint 3 32 and remove load compartment cover if necessary 3 51. ■ With the seat folded in the upright position, push the release lever and remove the seat assembly. ■ Store the head restraint on the rear of the seat frame. Seats, restraints Replacing the seats ■ Raise the backrest and replace the head restraint. ■ The backrest is properly engaged when red mark on the release lever is no longer visible. 37 Seat belts 9 Warning ■ Attach the seat assembly front supports on the anchor points. ■ Push the release lever to ensure the seat is securely latched. ■ Remove the head restraint from the rear of the seat frame. ■ Lower the seat assembly to the floor, ensuring the rear support is located on the anchor point and securely latched. When installing the seat, ensure that the seat is properly located on the anchor points, the locking catches are fully engaged, and the backrest is returned to the correct position. The seat belts are locked during heavy acceleration or deceleration of the vehicle holding the occupants in the sitting position. Therefore the risk of injury is considerably reduced. 9 Warning Fasten seat belt before each trip. In the event of an accident, people not wearing seat belts endanger their fellow occupants and themselves. 38 Seats, restraints Seat belts are designed to be used by only one person at a time. Child restraint system 3 44. Periodically check all parts of the belt system for damage, pollution and proper functionality. Have damaged components replaced. After an accident, have the belts and triggered belt pretensioners replaced by a workshop. Note Make sure that the belts are not damaged by shoes or sharp-edged objects or trapped. Prevent dirt from getting into the belt retractors. Seat belt reminder X 3 68. Belt force limiters On the front seats, stress on the body is reduced by the gradual release of the belt during a collision. Belt pretensioners In the event of a head-on or rear-end collision of a certain severity, the front seat belts are tightened. 9 Warning Incorrect handling (e.g. removal or fitting of belts) can trigger the belt pretensioners. Three-point seat belt Fastening Deployment of the belt pretensioners is indicated by continuous illumination of control indicator v 3 68. Triggered belt pretensioners must be replaced by a workshop. Belt pretensioners can only be triggered once. Note Do not affix or install accessories or other objects that may interfere with the operation of the belt pretensioners. Do not make any modifications to belt pretensioner components as this will invalidate the approval of your vehicle. Withdraw the belt from the retractor, guide it untwisted across the body and insert the latch plate into the buckle. Tighten the lap belt regularly whilst driving by pulling the shoulder belt. Seat belt reminder X 3 68. Seats, restraints 39 Height adjustment Loose or bulky clothing prevents the belt from fitting snugly. Do not place objects such as handbags or mobile phones between the belt and your body. 9 Warning The belt must not rest against hard or fragile objects in the pockets of your clothing. 1. Pull belt out slightly. 2. Press button down. 3. Adjust height and engage. Adjust the height so that the belt lies across the shoulder. It must not lie across the throat or upper arm. Do not adjust while driving. 40 Seats, restraints Removing To release belt, press red button on belt buckle. Seat belts on the rear seats The seat belt for the rear centre seat can only be withdrawn from the retractor if the backrest is in the rear position. Using the seat belt while pregnant 9 Warning The lap belt must be positioned as low as possible across the pelvis to prevent pressure on the abdomen. Airbag system The airbag system consists of a number of individual systems depending on the scope of equipment. When triggered, the airbags inflate within milliseconds. They also deflate so quickly that it is often unnoticeable during the collision. Note Depending on the severity of a collision, the fuel system may also be cut-off and the engine switched off automatically, for safety reasons. Resetting the fuel cut-off system; refer to "Fuel system messages" 3 80. Note Expiry dates for replacing the airbag system components may be found on the label inside the glovebox. Contact a workshop to have the airbag system components replaced. Seats, restraints 9 Warning If handled improperly the airbag systems can be triggered in an explosive manner. Note The airbag systems and belt pretensioner control electronics are located in the centre console area. Do not put any magnetic objects in this area. Do not fix any objects onto the airbag covers and do not cover them with other materials. Each airbag is triggered only once. Have deployed airbags replaced by a workshop. Furthermore, it might be necessary to have the steering wheel, the instrument panel, parts of the panelling, the door seals, handles and the seats replaced. Do not make any modifications to the airbag system as this will invalidate the vehicle type approval. 9 Warning When the airbags inflate, escaping hot gases may cause burns. 41 Additionally there is a warning label on the passenger's sun visor. Child restraint systems 3 44. Airbag deactivation 3 42. Control indicator v for airbag systems 3 68. Front airbag system The front airbag system consists of one airbag in the steering wheel and one in the instrument panel on the front passenger side. These can be identified by the word AIRBAG. The front airbag system is triggered in the event of a front-end impact of a certain severity. The ignition must be switched on. The inflated airbags cushion the impact, thereby reducing the risk of injury to the upper body and head of the front seat occupants considerably. 42 Seats, restraints 9 Warning Optimum protection is only provided when the seat is in the proper position 3 33. Keep the area in which the airbag inflates clear of obstructions. Fit the seat belt correctly and engage securely. Only then the airbag is able to protect. Side airbag system The side airbag system consists of an airbag in each front seat backrest. This can be identified by the word AIRBAG. The side airbag system is triggered in the event of a side impact of a certain severity. The ignition must be switched on. The inflated airbags cushion the impact, thereby reducing the risk of injury to the upper body and pelvis in the event of a side-on collision considerably. The side airbag systems, the belt pretensioners and all driver airbag systems will remain active. 9 Warning Keep the area in which the airbag inflates clear of obstructions. Note Only use protective seat covers that have been approved for the vehicle. Be careful not to cover the airbags. Airbag deactivation The front passenger airbag system must be deactivated if a child restraint system is to be fitted on this seat. The front passenger airbag system can be deactivated via the settings menu in the Driver Information Centre (DIC) 3 74. Note Two versions of the DIC are available; a Standard version and a Multifunction version with further adjustable settings. Seats, restraints Deactivate the front passenger airbag system as follows: 1. Press the SET ESC button once to access the settings menu. 2. Press SET ESC again (repeatedly) to cycle through the menu functions until menu option Pass bag (in Standard version) - or Passenger bag (in Multifunction version) is displayed. 3. Press the R or S button to switch from Pass bag On to Pass bag off (Standard version) - or from Passenger bag On to Passenger bag Off (Multifunction version) 4. Press SET ESC to confirm selection; A confirmation message appears in the display. 5. Press the R or S button to select Yes. 6. Press SET ESC briefly to confirm deactivation and automatically return to the previous display screen. Front passenger seat airbags are deactivated and will not inflate in the event of a collision. Control indicator * illuminates continuously in the instrument cluster. A child restraint system can be installed in accordance with the chart Child restraint installation locations 3 45. 9 Danger Risk of fatal injury for a child using a child restraint system on a seat with activated front passenger airbag. Risk of fatal injury for an adult person on a seat with deactivated front passenger airbag. 43 As long as the control indicator * is not illuminated, the front passenger airbag system will inflate in the event of a collision. If control indicators * and v are illuminated at the same time, there is a system failure. The status of the system is not discernible, therefore no person is allowed to occupy the front passenger seat. Contact a workshop immediately. Change status only when the vehicle is stationary. The status remains until the next change. Control indicator for airbag deactivation 3 69. Reactivating front passenger airbag system - see Driver Information Centre (DIC) 3 74. 44 Seats, restraints Child restraints Child restraint systems We recommend the Opel child restraint system which is tailored specifically to the vehicle. When a child restraint system is being used, pay attention to the following usage and installation instructions and also those supplied with the child restraint system. Always comply with local or national regulations. In some countries, the use of child restraint systems is forbidden on certain seats. 9 Warning When using a child restraint system on the front passenger seat, the airbag systems for the front passenger seat must be deactivated; if not, the triggering of the airbags poses a risk of fatal injury to the child. This is especially the case if rearfacing child restraint systems are used on the front passenger seat. Selecting the right system The rear seats are the most convenient location to fasten a child restraint system. Children should travel facing rearwards in the vehicle as long as possible. This makes sure that the child's backbone, which is still very weak, is under less strain in the event of an accident. Suitable restraint systems comply with ECE 44-03 or ECE 44-04. Check local laws and regulations for mandatory use of child restraint systems. Ensure that the child restraint system to be installed is compatible with the vehicle type. Ensure that the mounting location of the child restraint system within the vehicle is correct. Allow children to enter and exit the vehicle only on the side facing away from the traffic. When the child restraint system is not in use, secure the seat with a seat belt or remove it from the vehicle. Note Do not stick anything on the child restraint systems and do not cover them with any other materials. A child restraint system which has been subjected to stress in an accident must be replaced. Seats, restraints 45 Child restraint installation locations Permissible options for fitting a child restraint system Front passenger seat Second row Third row Weight and age class activated airbag deactivated airbag outboard seat centre seat Group 0: up to 10 kg or approx. 10 months X U1 U, < U X Group 0+: up to 13 kg or approx. 2 years X U1 U, < U X Group I: 9 to 18 kg or approx. 8 months to 4 years X U1 U, < U X Group II: 15 to 25 kg or approx. 3 to 7 years X X U U X Group III: 22 to 36 kg or approx. 6 to 12 years X X U U X = Only if front airbag system is deactivated. When securing with a three-point seat belt, move seat height adjustment to uppermost position and ensure that the seat belt runs forwards from the upper anchorage point. < = Vehicle seat available with ISOFIX attachments. When attaching using ISOFIX, only the ISOFIX child restraint systems permitted for the vehicle may be used. U = Universal suitability in conjunction with three-point seat belt. X = No child restraint system permitted in this weight class. 1 46 Seats, restraints Permissible options for fitting an ISOFIX child restraint system On front passenger seat On outboard seats On centre seat in On the seats in in the second row the second row the third row Weight class Size class Fixture Group 0: up to 10 kg E ISO/R1 X IL X X Group 0+: up to 13 kg E ISO/R1 X IL X X D ISO/R2 X IL X X C ISO/R3 X IL1) X X D ISO/R2 X IL X X C ISO/R3 X IL1) X X B ISO/F2 X IUF X X B1 ISO/F2X X IUF X X A ISO/F3 IUF X X Group I: 9 to 18 kg X IL = Suitable for particular ISOFIX restraint systems of the 'specific-vehicle', 'restricted' or 'semi-universal' categories. The ISOFIX restraint system must be approved for the specific vehicle type. IUF = Suitable for ISOFIX forward-facing child restraint systems of universal category approved for use in this weight class. X = No ISOFIX child restraint system approved in this weight class. 1) The Isofix child seat can be installed by lifting the head restraint all the way up. Seats, restraints ISOFIX size class and seat device A – ISO/F3 B – ISO/F2 B1 – ISO/F2X C – ISO/R3 D – ISO/R2 E – ISO/R1 = = = = = = Forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kg. Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg. Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg. Rear-facing child restraint system for children of maximum size in the weight class up to 13 kg. Rear-facing child restraint system for smaller children in the weight class up to 13 kg. Rear-facing child restraint system for young children in the weight class up to 13 kg. 47 48 Seats, restraints ISOFIX child restraint systems Fasten vehicle-approved ISOFIX child restraint systems to the ISOFIX mounting brackets. Specific vehicle ISOFIX child restraint system positions are marked in the table by IL. ISOFIX mounting brackets are indicated by a label on the backrest. Before fastening a child seat adjust the head restraint to use position 3 32. Top-tether fastening eyes In addition to the ISOFIX mounting, fasten the Top-Tether strap to the Top-Tether fastening eyes. The strap must run between the two guide rods of the head restraint. ISOFIX child restraint systems of universal category positions are marked in the table by IUF. Storage Storage Storage compartments 49 Document holder Instrument panel storage Storage compartments ................ 49 Load compartment ....................... 51 Roof rack system ......................... 54 Loading information ..................... 55 Storage compartments are located in the instrument panel. Pull the rear of the document holder upwards from the instrument panel and rest in tilted position. To fold away, lower the document holder back into the instrument panel, pressing down until it engages audibly. 50 Storage Glovebox Overhead console Underseat storage To open the glovebox, pull the handle. Depending on version, the glovebox may be lockable. The glovebox should be closed whilst driving. Store only lightweight items such as paperwork or maps in the overhead console. Pull the loop on the seat cushion to gain access to the storage area. Cupholders Cupholders are located in the centre console. The cupholders can also be used to hold the portable ashtray unit 3 62. Storage Load compartment To fold up, lower seats to the floor until they engage audibly. Raise backrests and guide them into an upright position until they engage audibly. The backrests are properly engaged when both red marks on the release levers are no longer visible. Ensure that the seat belts are positioned correctly before returning the seats to the upright position. Folding down rear seat backrests The rear seat backrest is divided into two parts. Both parts can be folded down. Remove the load compartment cover if necessary. Press and hold the catch, then push the head restraints down. 51 Pull lever to release, the seat base is tensioned and will start to rise automatically. 9 Warning Only drive the vehicle if the backrests are securely locked into position. Otherwise there is a risk of personal injury or damage to the load or vehicle in the event of heavy braking or a collision. Load compartment cover Pull the release lever on one or both sides and fold down the backrests onto the seat cushion. Extendable load compartment cover Fold the seat forward completely. Do not place any heavy or sharpedged objects on the extendable load compartment cover. 52 Storage Closing Opening Removing Pull the cover towards the rear using the handle and engage it in the retainers at the sides. Remove load compartment cover from the retainers at the sides. Hold the cover and guide it until it is fully rolled up. Open the load compartment cover. Pull the release lever and lift cover from retainers. Installing Insert either side of the load compartment cover in the recess, pull the release lever. Insert the load compartment cover and engage. Storage Rear parcel shelf or the lower position. In the lower position, the maximum load permissible is 70 kg. The rear parcel shelf consists of two parts - a front part and rear part. The front part can be opened or closed, allowing for greater flexibility in the load compartment. Do not place any excessively heavy or sharp-edged objects on the rear parcel shelf. Removing If the rear seats are in the folded position, remove the parcel shelf and store it horizontally between the back of the front seats and the folded rear seats. 9 Warning Always make sure that the load in the vehicle is securely stowed. Otherwise objects can be thrown around inside the vehicle and cause personal injury or damage to the load or car. 53 Caution The rear parcel shelf can be installed in 2 positions, i.e. the upper position For safety reasons, do not place loads on the folded rear seats. 54 Storage To remove, lift the front part of the parcel shelf by releasing it from the front retainers (1) on both sides. Lift the rear part of the parcel shelf by releasing it from the rear retainers (2 and 3) on both sides. Installing Refit the parcel shelf by engaging in front and rear retainers on both sides. Lashing eyes Van The lashing eyes are designed to secure items against slippage, e.g. using lashing straps or a luggage net. Roof rack system Combo Tour For safety reasons and to avoid damage to the roof, the vehicle approved roof rack system is recommended. Contact a workshop for further information. Follow the installation instructions and remove the roof rack when not in use. Roof rack Mounting roof rack Storage To fasten a roof rack, insert the mounting bolts in the holes indicated in the illustration. Loading information ■ Heavy objects in the load compartment should be evenly distributed and placed as far forward as possible. If objects can be stacked, the heavier objects should be placed at the bottom. ■ Secure objects with lashing straps attached to lashing eyes 3 54. ■ Secure loose objects in load compartment to prevent sliding. ■ When transporting objects in the load compartment, the backrests of the rear seats must not be tilted forwards or folded down. ■ Do not allow the load to protrude above the upper edge of the backrests. ■ Do not place any objects on the extendable load compartment cover 3 51 or the instrument panel. ■ The load must not obstruct the operation of the pedals, parking brake and gear selector, or hinder 55 the freedom of movement of the driver. Do not place any unsecured objects in the interior. ■ Do not drive with an open load compartment. 9 Warning Always make sure that the load in the vehicle is securely stowed. Otherwise objects can be thrown around inside the vehicle and cause personal injury or damage to the load or car. ■ The payload is the difference between the permitted gross vehicle weight (see identification plate 3 154) and the EC kerb weight. To calculate the payload, enter the data for your vehicle in the Weights table at the front of this manual. The EC kerb weight includes weights for the driver (68 kg), luggage (7 kg) and all fluids (tank 90 % full). 56 Storage Optional equipment and accessories increase the kerb weight. ■ Driving with a roof load increases the sensitivity of the vehicle to cross-winds and has a detrimental effect on vehicle handling due to the vehicle's higher centre of gravity. Distribute the load evenly and secure it properly with retaining straps. Adjust the tyre pressure and vehicle speed according to the load conditions. Check and retighten the straps frequently. Do not drive faster than 120 km/h. The permissible roof load (which includes the weight of the roof rack) is 100 kg. The roof load is the combined weight of the roof rack and the load. Instruments and controls Instruments and controls Controls 57 Steering wheel controls Steering wheel adjustment Controls ....................................... 57 Warning lights, gauges and indicators ..................................... 63 Information displays ..................... 74 Vehicle messages ........................ 80 Trip computer ............................... 81 Unlock lever, adjust steering wheel, then engage lever and ensure it is fully locked. Do not adjust steering wheel unless vehicle is stationary and steering wheel lock has been released. The Infotainment system and a connected mobile phone can be operated via the controls on the steering wheel. Further information is available in the Infotainment system manual. 58 Horn Instruments and controls Windscreen wiper/washer Windscreen wiper Adjustable wiper interval Wiper lever in position Ç. The windscreen wiper will automatically adapt to the speed of the vehicle. Windscreen washer Press j. Twist É È Ç § = = = = fast slow intermittent wiping off For a single wipe when the windscreen wiper is off, move the lever up. Do not use if the windscreen is frozen. Switch off in car washes. Pull lever briefly, washer fluid is sprayed onto the windscreen and the wiper wipes a few times. Pull lever and hold, washer fluid is sprayed onto the windscreen and wiper wipes until the lever is released. Instruments and controls Rear window wiper/washer Outside temperature 59 Clock Depending on model variant, the current time and/or date may appear in the Driver Information Centre (DIC) 3 74. Values can be adjusted via the SET ESC, R and S buttons on the instrument panel. Twist to activate the rear window wiper. Push lever. Washer fluid is sprayed onto the rear window and the wiper wipes a few times. Do not use if the rear window is frozen. Switch off in car washes. The rear window wiper comes on automatically when the windscreen wiper is switched on and reverse gear is engaged. Outside temperature is shown in the Driver Information Centre (DIC) 3 74. 9 Warning The road surface may already be icy even though the display indicates a few degrees above 0 °C. 60 Instruments and controls Set time in Driver Information Centre - Standard version 6. Press R or S to increase or decrease the displayed value. 7. Press SET ESC briefly to confirm changes and automatically return to the previous display screen. Set time and date in Driver Information Centre Multifunction version 1. Press the SET ESC button once to access the settings menu. 2. Scroll through the menu options using the R or S buttons until HOUR is displayed. 3. Press SET ESC to access this menu option; the hours will flash in the display. 4. Press R or S to increase or decrease the displayed value. 5. Press SET ESC to confirm changes; the minutes will flash in the display. Setting the time After accessing this menu option, it is possible to either set the time or change the clock mode between 12 hour and 24 hour clock. Press the SET ESC button once to access the settings menu. Scroll through the menu options using the R or S buttons until Set time is displayed. Press SET ESC to access this menu option; Time and Mode are displayed. To set the time: 1. Press R or S to select Time and press SET ESC to access this submenu option; the hours will flash in the display 2. Press R or S to increase or decrease the displayed value. 3. Press SET ESC to confirm changes; the minutes will flash in the display. 4. Press R or S to increase or decrease the displayed value. 5. Press SET ESC briefly to confirm changes and automatically return to the previous display screen. Instruments and controls To change the clock mode between 12 hour and 24 hour clock: 1. Press R or S to select Mode and press SET ESC to access this submenu option; the display will flash. 2. Press R or S to change clock mode between 12h and 24h. 3. Press SET ESC briefly to confirm changes and automatically return to the previous display screen. Setting the date 1. Press the SET ESC button once to access the settings menu. 2. Scroll through the menu options using the R or S buttons until Set date is displayed. 3. Press SET ESC to access this menu option; the year will flash in the display. 4. Press R or S to increase or decrease the displayed value. 5. Press SET ESC to confirm changes; the month will flash in the display. 6. Press R or S to increase or decrease the displayed value. 7. Press SET ESC to confirm changes; the day will flash in the display. 8. Press R or S to increase or decrease the displayed value. 9. Press SET ESC briefly to confirm changes and automatically return to the previous display screen. Power outlets A 12 Volt power outlet is located in the centre console. Rear power outlets 61 Depending on model variant,12 Volt power outlets are located at the sidewall in the load compartment. Short wheelbase van 62 Instruments and controls Long wheelbase van Combo Tour Do not exceed the maximum power consumption of 180 watts. With ignition off, the power outlets are deactivated. Additionally the power outlets are deactivated in the event of low battery voltage. Electrical accessories that are connected must comply with the electromagnetic compatibility requirements laid down in DIN VDE 40 839. Do not connect any current-delivering accessories, e.g. electrical charging devices or batteries. Do not damage the power outlets by using unsuitable plugs. If the tyre repair kit is in operation, switch off all electrical consumers. Tyre repair kit 3 137. Cigarette lighter The cigarette lighter is located in the centre console. Press in cigarette lighter. It switches off automatically once the element is glowing. Pull out lighter. Ashtrays Caution To be used only for ash and not for combustible rubbish. Instruments and controls Warning lights, gauges and indicators 63 Odometer Speedometer The portable ashtray should be placed in the cupholders in the centre console. Displays the recorded distance in km. H may appear in the display until the vehicle has travelled 100 km. Indicates vehicle speed. Trip odometer Displays the recorded distance since the last reset. Depending on model variant, there are two independent trip odometers A or B which indicate how far the vehicle has been driven since the last reset. 64 Instruments and controls To reset the trip odometer, press and hold the TRIP button for a few seconds while the relevant trip odometer is displayed. Tachometer Caution If the needle is in the red warning zone, the maximum permitted engine speed is exceeded. Engine at risk. Fuel gauge Never run the tank dry. Because of the fuel remaining in the tank, the top-up quantity may be less than the specified tank capacity. The needle will point to 0 and control indicator $ will flash to indicate a fault in the system. Seek the assistance of a workshop. Low fuel control indicator $ 3 73. CNG fuel gauge Displays the engine speed. Drive in a low engine speed range for each gear as much as possible. Displays the fuel level or gas level in the tank depending on the operation mode. Fuel selector 3 112. Control indicator $ illuminates if the level in the tank is low. In natural gas operation mode, the four vertical bars next to CNG correspond to the methane level in Instruments and controls the cylinders. As the fuel level diminishes, the bars in the CNG fuel gauge disappear. CNG and the one remaining bar will flash if the methane level in the cylinders is low. Refuelling 3 113. Engine coolant temperature gauge 3 74 the coolant temperature is too high. Seek the assistance of a workshop. Caution If engine coolant temperature is too high, stop vehicle, switch off engine. Danger to engine. Check coolant level. Fuel selector Y illuminates in the Driver Information Centre. Natural gas tanks are empty, petrol operation is automatically engaged. Fuel for natural gas operation 3 112, Refuelling 3 113. 65 Service display Displays the coolant temperature. C = engine operating temperature not yet reached central = normal operating area temperature H = temperature too high If control indicator $ illuminates in conjunction with a message in the Driver Information Centre (DIC) When the ignition is switched on, the remaining distance before the next service is due may be shown briefly in the Driver Information Centre (DIC) 66 Instruments and controls 3 74. Based on driving conditions, the interval at which a service will be indicated can vary considerably. When the remaining distance before the next service is less than 2,000 km, Serv. appears in the Driver Information Centre. The service reminder is repeated after every additional 200 km and becomes more frequent when the remaining distance is below 200 km. The vehicle needs a service. Seek the assistance of a workshop. The remaining distance to the next service may also be viewed in the Driver Information Centre (DIC) by selecting SERVICE from the settings menu options 3 74. Resetting the service display After a service, the service display must be reset by a workshop. Control indicators The control indicators described are not present in all vehicles. The description applies to all instrument versions. Depending on the equipment, the position of the control indicators may vary. When the ignition is switched on, most control indicators will illuminate briefly as a functionality test. The control indicator colours mean: red = danger, important reminder yellow = warning, information, fault green = confirmation of activation blue = confirmation of activation Instruments and controls Control indicators in the instrument cluster 67 68 Instruments and controls Generic warning 9 illuminates yellow. Depending on model variant, control indicator 9 may illuminate independently or in conjunction with Æ, t, Z or r. If 9 illuminates together with I; stop engine immediately and seek the assistance of a workshop. Simultaneously a warning message may be displayed in the Driver Information Centre (DIC) 3 74. 9 also illuminates if the fuel cut-off switch is triggered, or if a fault is detected in the engine oil pressure sensor. Consult a workshop. Fuel cut-off system 3 80. Turn signal 2 or 3 flashes green. Flashes A turn signal or the hazard warning flashers are activated. Rapid flashing: failure of a turn signal light or associated fuse, failure of turn signal light on trailer. Bulb replacement 3 125, Fuses 3 131. Turn signals 3 85. Seat belt reminder Seat belt reminder for front seats X for driver's seat and/or front passenger seat illuminates or flashes red. Illuminates When the ignition has been switched on, control indicator X illuminates briefly if driver's seat belt and/or front passenger seat belt is not engaged. A warning chime also sounds for a few seconds. Flashes During driving X will flash and a warning chime will sound for 90 seconds until the front seat belts are fastened. Fastening the seat belt 3 38. 9 Warning Fasten seat belt before each trip. In the event of an accident, people not wearing seat belts endanger their fellow occupants and themselves. To deactivate the seat belt reminder, consult a workshop. Reactivation of the warning chime for seat belt reminder can be done via the Driver Information Centre (DIC) 3 74. Note The volume of the warning chime can also be adjusted via the DIC. Driver Information Centre (DIC) 3 74. Airbag and belt tensioners v illuminates red. When the ignition is switched on, the control indicator illuminates for approx. 4 seconds. If it does not illuminate, does not go out after 4 seconds or illuminates whilst Instruments and controls driving, there is a fault in the airbag system. Seek the assistance of a workshop. The airbags and belt pretensioners may fail to trigger in the event of an accident. Deployment of the belt pretensioners or airbags is indicated by continuous illumination of v. 9 Warning Have the cause of the fault remedied immediately by a workshop. Belt pretensioners, airbag system 3 37, 3 40. Airbag deactivation * illuminates yellow. With the front passenger airbag activated: When the ignition is switched on, * illuminates for approx. 4 seconds, flashes for another 4 seconds and then extinguishes. With the front passenger airbag deactivated: * permanently illuminates yellow. Airbag deactivation 3 42. 9 Danger Risk of fatal injury for a child using a child restraint system together with activated front passenger airbag. Risk of fatal injury for an adult person with deactivated front passenger airbag. Charging system p illuminates red. Illuminates when the ignition is switched on and extinguishes shortly after the engine starts. 69 Illuminates when the engine is running Stop, switch off engine. Battery is not charging. Engine cooling may be interrupted. The brake servo unit may cease to be effective. Seek the assistance of a workshop. Malfunction indicator light Z illuminates or flashes yellow. Illuminates when the ignition is switched on and extinguishes shortly after the engine starts. Illuminates when the engine is running Fault in the emission control system. The permitted emission limits may be exceeded. Seek the assistance of a workshop immediately. 70 Instruments and controls Flashes when the engine is running Fault that could lead to catalytic converter damage. Ease up on the accelerator until the flashing stops. Seek the assistance of a workshop immediately. Brake system R illuminates red. Illuminates when the parking brake is released if the brake fluid level is too low 3 123. 9 Warning Stop. Do not continue your journey. Consult a workshop. Illuminates if the brake vacuum servo fails; the brake pedal becomes stiff when pressed. The brake system remains operational however, assistance will be reduced. The steering may also require considerably more effort when turning. Illuminates after the ignition is switched on if the parking brake is applied 3 106. Brake pad wear F illuminates yellow. The front brake pads are worn, seek the assistance of a workshop immediately. Antilock brake system (ABS) u illuminates yellow. Illuminates for a few seconds after the ignition is switched on. The system is ready for operation when the control indicator extinguishes. If the control indicator does not extinguish after a few seconds, or if it illuminates while driving, there is a fault in the ABS. The brake system remains operational but without ABS regulation. Antilock brake system 3 105. Upshift [ or Ò illuminates in the Driver Information Centre (DIC) 3 74 when gearshifting is recommended to improve fuel economy. Hill start assist Z illuminates yellow. Illuminates when the ignition is switched on and extinguishes shortly after the engine starts. If the control indicator does not extinguish after a few seconds, or if it illuminates while driving, there is a fault in the Hill start assist. Seek the assistance of a workshop to have the fault remedied. The Electronic Stability Program fault control indicator x may also illuminate 3 71 in conjunction with Z. Depending on model variant, 9 will illuminate as an alternative if control indicator Z is not present. A warning Instruments and controls message may also be displayed in the Driver Information Centre (DIC) 3 74. Generic warning 9 3 68. Ultrasonic parking assist 3 109. Generic warning 9 3 68. Hill start assist 3 106. Electronic Stability Program fault Ultrasonic parking assist x illuminates or flashes yellow. r illuminates yellow. Fault in system or Fault due to sensors that are dirty or covered by ice or snow or Interference due to external sources of ultrasound. Once the source of interference is removed, the system will operate normally. Have the cause of the fault in the system remedied by a workshop. Depending on version, 9 will illuminate as an alternative if control indicator r is not present. A warning message may also be displayed in the Driver Information Centre (DIC) 3 74. Illuminates A fault in the system is present. Continued driving is possible. Driving stability, however, may deteriorate depending on road surface conditions. Have the cause of the fault remedied by a workshop. Flashes The system is actively engaged. Engine output may be reduced and the vehicle may be braked automatically to a small degree. Electronic Stability Program 3 107, Traction Control system (ASR) 3 107. 71 Engine coolant temperature $ illuminates red. Illuminates for a few seconds after the ignition is switched on. If control indicator $ illuminates in conjunction with a message in the Driver Information Centre (DIC), the coolant temperature is too high. Seek the assistance of a workshop. Driver Information Centre (DIC) 3 74. Caution If engine coolant temperature is too high, stop vehicle, switch off the ignition. Danger to engine. Check coolant level. If the control indicator remains on, seek the assistance of your workshop. Engine coolant temperature gauge 3 65. 72 Instruments and controls Preheating ! illuminates yellow. Preheating is activated. Only activates when outside temperature is low. Diesel particle filter [ illuminates yellow. The diesel particle filter requires cleaning. Continue driving until [ extinguishes. If possible, do not allow engine speed to drop below 2000 rpm. Illuminates The diesel particle filter is full. Start cleaning process as soon as possible. Diesel particle filter 3 99, Stop-start system 3 97. Engine oil pressure I illuminates red. Illuminates when the ignition is switched on and extinguishes shortly after the engine starts. Illuminates when the engine is running Caution Engine lubrication may be interrupted. This may result in damage to the engine and/or locking of the drive wheels. 1. Depress clutch. 2. Select neutral gear, set selector lever to N. 3. Move out of the flow of traffic as quickly as possible without impeding other vehicles. 4. Switch off ignition. 9 Warning When the engine is off, considerably more force is needed to brake and steer. During an Autostop the brake servo unit will still be operational. Do not remove key until vehicle is stationary, otherwise the steering wheel lock could engage unexpectedly. Check oil level before seeking the assistance of a workshop 3 120. Change engine oil Diesel engines with diesel particle filter I flashes red. Illuminates when the ignition is switched on and extinguishes shortly after the engine starts. The engine oil life monitor lets you know when to change the oil. Control indicator I will flash, together with a message in the Driver Information Instruments and controls Centre (DIC), to indicate that engine oil life has been diminished and the oil needs changing. Based on driving conditions, the interval at which an oil change will be indicated can vary considerably. Depending on model variant, I may flash in the following ways: ■ for 1 minute every 2 hours, or ■ for 3 minute cycles with I off for intervals of 5 seconds. The warning will be repeated every time the engine is started, until the engine oil is changed and the service display is reset. Seek the assistance of a workshop. Service display 3 65. If the control indicator does not extinguish after a few seconds, or if it illuminates while driving, the engine oil level is insufficient. Check oil level before seeking the assistance of a workshop 3 120. Low engine oil level Flashes y illuminates red. Illuminates when the ignition is switched on and extinguishes shortly after the engine starts. Low fuel $ illuminates or flashes yellow. Illuminates for a few seconds after the ignition is switched on. Illuminates Level in fuel tank is too low. Refuel immediately 3 113. Never run the tank dry. Catalytic converter 3 100. Fault in fuel system. Have the cause of the fault remedied by a workshop. Fuel gauge 3 64. 73 Drain fuel filter z illuminates yellow. Illuminates when the ignition is switched on and goes out shortly after the engine starts. Illuminates when the engine is running Indicates the presence of water in the diesel. Seek the assistance of a workshop immediately. Immobiliser d illuminates yellow. Fault in the immobiliser system. The engine cannot be started. Stop-start system Æ illuminates yellow. A fault is present in the system. Have the cause of the fault remedied by a workshop. 74 Instruments and controls Depending on version, 9 will illuminate as an alternative if control indicator Æ is not present. A warning message may also be displayed in the Driver Information Centre (DIC) 3 74. Generic warning 9 3 68. Stop-start system 3 97. Exterior light 8 illuminates green. The exterior lights are on 3 83. Exterior light failure µ illuminates yellow. One or more of the exterior lights is faulty 3 125. Depending on version, 9 will illuminate as an alternative if control indicator µ is not present. A warning message may also be displayed in the Driver Information Centre (DIC) 3 74. Generic warning 9 3 68. High beam C illuminates blue. Illuminated when high beam is on and during headlight flash 3 83. Information displays Driver Information Centre Fog light > illuminates green. The front fog lights are on 3 85. Rear fog light r illuminates yellow. The rear fog light is on 3 86. Cruise control m illuminates green. The system is on. Cruise control 3 108. Door open \ illuminates red. A door or the tailgate is open. The Driver Information Centre (DIC) is located in the instrument cluster between the speedometer and tachometer. Two versions are available; a Standard version Instruments and controls ■ ■ ■ ■ Transmission display 3 101 Stop-start system indicator 3 97 Vehicle messages 3 80 Trip computer 3 81 Selecting menus and options The menus and options can be selected via the buttons on the instrument panel. and a Multifunction version with further adjustable settings. Some of the displayed functions differ when the vehicle is being driven or at a standstill. Some options are only available when the vehicle is being driven. Depending on model variant, the following items appear in the display: ■ Odometer, trip odometer 3 63 ■ Clock 3 59 ■ Outside temperature 3 59 ■ Headlight range adjustment 3 84 75 Press the SET ESC button: ■ once to access the settings menu ■ press again to access a menu option and submenu options ■ after changes have been made, briefly press again to confirm a value and automatically return to the previous display screen Alternatively, press and hold the SET ESC button to return to the previous display screen without saving changes to the current menu option. Note The settings menu is exited automatically after a delay. Only changes already confirmed by briefly pressing the SET ESC button are stored. 76 Instruments and controls Settings menu options Standard version Press the R button to scroll up the screen and the menu options or to increase the displayed value. Press and hold to increase value rapidly (press again to stop on the required value). Press the S button to scroll down the screen and the menu options or to decrease the displayed value. Press and hold to decrease value rapidly (press again to stop on the required value). The settings menu contains the following options: ■ ILLU ■ SPEEd ■ HOUR ■ UNIT ■ bUZZ ■ BAG P ■ DRL ILLU (Brightness of interior lighting) When driving at night with the low beam on, adjust the brightness of the vehicle's interior lighting (e.g. instrument panel, climate control display). SPEEd (Speed limit warning chime) Activate or deactivate the speed limit warning chime or change the speed limit. Speeds between 30 and 200 km/h can be stored. When activated, the driver is alerted with a warning chime when the set speed limit is exceeded. After accessing this menu option, activate or deactivate the function (set to On or Off) and confirm. Press the SET ESC button when activated (On) to access the current set speed. Adjust as required and confirm. Warning chimes 3 80. HOUR (Setting the clock) Adjust the hours setting (flashing value) and confirm. Adjust minutes setting (flashing value) and confirm. Clock 3 59. UNIT (Unit of measurement) Set the unit of measurement to km or miles. bUZZ (Warning chime volume) Adjust the volume of warning chimes and confirm. 8 volume levels are available. A chime is also sounded every time the SET ESC, R or S button is pressed. Warning chimes 3 80. Instruments and controls BAG P (Passenger front and side airbags activation/deactivation) Activate the front passenger airbags if an adult is occupying the front passenger seat. Deactivate airbags when a child restraint system is installed on this seat. 9 Danger Risk of fatal injury for a child using a child restraint system on a seat with activated front passenger airbag. Risk of fatal injury for an adult person on a seat with deactivated front passenger airbag. After accessing this menu option, activate or deactivate the airbags (BAG P On or BAG P Off) and confirm; a confirmation message appears in the display. Select YES (to confirm changes) or No (to cancel changes). Airbag deactivation 3 42. DRL (Daytime running lights) Activate the daytime running lights to increase visibility of the vehicle during daylight (set to On). Deactivate when not required (set to Off). Daytime running lights 3 84. Settings menu options Multifunction version The settings menu contains the following options: ■ Lighting ■ Speed beep ■ Trip B data ■ Set time ■ Set date ■ Radio info ■ Autoclose ■ Unit of measurement ■ Language ■ Warning volume ■ Button volume ■ Seat belt buzzer ■ Service 77 ■ Passenger airbag ■ Daytime running lights ■ Exit menu LIGHTING (Brightness of interior lighting) When driving at night with the low beam on, adjust the brightness of the vehicle's interior lighting (e.g. instrument panel, climate control display). It is also possible to adjust the brightness using the R or S buttons without accessing the settings menu. SPEED BEEP (Speed limit warning chime) Activate or deactivate the speed limit warning chime or change the speed limit. Speeds between 30 and 200 km/h can be stored. When activated, the driver is alerted with a warning chime when the set speed limit is exceeded. After accessing this menu option, activate or deactivate the function (set to On or Off) and confirm. 78 Instruments and controls Press the SET ESC button when activated (On) to access the current set speed. Adjust as required and confirm. Warning chimes 3 80. TRIP B DATA Activate or deactivate the second trip computer (set to On or Off). Trip B records average consumption, distance travelled, average speed and travel time (driving time). The measurement can be restarted at any time. Trip computer 3 81. SET TIME (Setting the clock and clock mode) After accessing this menu option, it is possible to either set the time or change the clock mode between 12 hour and 24 hour clock. Select Time and confirm. Adjust the hours setting (flashing value) and confirm. Adjust minutes setting (flashing value) and confirm. Select Mode and confirm. Select 12h or 24h and confirm. Clock 3 59. SET DATE Adjust the year setting (flashing value) and confirm. Adjust month setting (flashing value) and confirm. Adjust the day setting (flashing value) and confirm. RADIO INFO (Display audio and radio information) Activate radio info (set to On) to display audio and radio information (e.g. station frequency, RDS messages, track number). Deactivate when not required (set to Off). Select Distance and confirm. Set the unit of measurement to km or mi (miles) and confirm. Select Consumption and confirm. When the Distance unit is set to km, it is possible to set the unit of measurement for fuel consumption to either l/100km or km/l. When the Distance unit is set to mi (miles), fuel consumption is shown in mpg. Select Temperature and confirm. Set the unit of measurement to °C or °F and confirm. AUTOCLOSE (Automatic central locking when driving) Activate the autoclose feature (set to On) to automatically lock the doors when vehicle speed exceeds 20 km/h. Deactivate when not required (set to Off). LANGUAGE (for Display messages) Display messages can be shown in different languages, including: English, German, French, Italian, Portuguese, Spanish, Dutch, Polish and Turkish. Select desired language and confirm. UNIT OF MEASUREMENT (for Distance, Fuel consumption and Temperature) After accessing this menu option, it is possible to set the unit of measurement for distance, fuel consumption and temperature. WARNING VOLUME (Warning chime volume) Adjust the volume of warning chimes and confirm. 8 volume levels are available. Warning chimes 3 80. Instruments and controls BUTTON VOLUME A chime is sounded every time the SET ESC, R or S button is pressed. Adjust the volume of these chimes and confirm. 8 volume levels are available. Warning chimes 3 80. SEAT BELT BUZZER (Reactivate warning chime for driver and/or front passenger seat belt reminder) This menu option is available only when the seat belt reminder has already been deactivated by a workshop. When reactivated, the driver and/or front passenger are alerted with a warning chime when the corresponding seat belt is not fastened. Seat belt reminder 3 68. SERVICE (Distance to next service) Access this menu option to view the remaining distance to the next service. The distance to next service is also displayed automatically when the distance reaches 2,000 km and is repeated after every additional 200 km. Service display 3 65. PASSENGER AIRBAG (Passenger front and side airbags activation/ deactivation) Activate the front passenger airbags if an adult is occupying the front passenger seat. Deactivate airbags when a child restraint system is installed on this seat. 9 Danger Risk of fatal injury for a child using a child restraint system on a seat with activated front passenger airbag. Risk of fatal injury for an adult person on a seat with deactivated front passenger airbag. After accessing this menu option, activate or deactivate the airbags (Bag Pass On or Bag Pass Off) and 79 confirm; a confirmation message appears in the display. Select YES (to confirm changes) or No (to cancel changes). Airbag deactivation 3 42. DAYTIME RUNNING LIGHTS Activate the daytime running lights to increase visibility of the vehicle during daylight (set to On). Deactivate when not required (set to Off). Daytime running lights 3 84. EXIT MENU Select this menu option to exit the settings menu. 80 Instruments and controls Vehicle messages Warning chimes Only one warning chime will sound at a time. When starting the engine or whilst driving ■ If seat belt is not fastened. ■ If a certain speed is exceeded with the parking brake applied. ■ If the parking assist detects an object. ■ If a fault is detected in the parking assist. ■ If a door or the tailgate is not fully closed when starting-off. ■ If the vehicle speed briefly exceeds a set limit. ■ Vehicles with manual transmission automated; neutral is not selected or the foot brake has not been depressed. ■ If a transmission fault is detected in vehicles with manual transmission automated. ■ If a warning message appears in the Driver Information Centre (DIC). When the vehicle is parked and/or the driver's door is opened ■ When the key is in the ignition switch. ■ Vehicles with manual transmission automated; neutral is not selected, the parking brake is not applied, or the foot brake and/or the accelerator pedal has not been depressed. Fuel system messages Fuel cut-off system In the event of a collision of a certain severity, the fuel system is cut-off and the engine is switched off automatically, for safety reasons. A corresponding warning message may also appear in the Driver Information Centre (DIC) 3 74. To reset the fuel cut-off system and enable the vehicle to be driven, refer to "Vehicle shutdown" 3 96. Instruments and controls Trip computer The trip computer provides information on driving data, which is continually recorded and evaluated electronically. The following functions can be selected by pressing the TRIP button repeatedly on the end of the wiper lever: Standard version ■ Average consumption ■ Instantaneous consumption ■ Range 81 ■ Distance travelled ■ Average speed ■ Travel time (driving time) Trip B can be deactivated via the Driver Information Centre (DIC) 3 74. Multifunction version To reset the trip computer, select one of its functions, then press and hold the TRIP button for a few seconds. Two trip odometers, Trip A and Trip B, are available for selection and are recorded separately. The information of the two trip computers can be reset separately, making it possible to display different trip distances. Trip A ■ Average consumption ■ Instantaneous consumption ■ Range ■ Distance travelled ■ Average speed ■ Travel time (driving time) Trip B ■ Average consumption ■ Distance travelled ■ Average speed ■ Travel time (driving time) Reset trip computer information The following trip computer information will be reset: ■ Average consumption ■ Distance travelled ■ Average speed ■ Travel time (driving time) 82 Instruments and controls The trip computer will reset automatically when the maximum value of any of the parameters is exceeded. Average consumption Average consumption is displayed, taking into consideration the distance travelled and the fuel used since the last reset. The measurement can be restarted at any time. Instantaneous consumption Display of the instantaneous fuel consumption. _ _ _ _ will appear in the display if the vehicle is left parked with the engine running for a long time. Range The range is calculated from the current contents of the fuel tank and the average consumption since the last reset. When the range is less than 50 km, _ _ _ _ will appear in the display. After refuelling, the range is updated automatically after a brief delay. The measurement can be restarted at any time. Note The range will not be displayed if the vehicle is left parked with the engine running for a long time. Distance travelled Displays the distance driven since the last reset. The measurement can be restarted at any time. Average speed The average speed since the last reset is displayed. The measurement can be restarted at any time. Interruptions in the journey with the ignition off are not included in the calculations. Travel time (driving time) The time elapsed since the since the last reset is displayed. The measurement can be restarted at any time. Exit trip computer To exit the trip computer, press and hold the SET ESC button for more than 2 seconds. Driver Information Centre (DIC) 3 74. Interruption of power supply If the power supply has been interrupted or if the battery voltage has dropped too low, the values stored in the trip computer will be lost. Lighting Lighting Exterior lighting 83 High beam Light switch Exterior lighting ............................ 83 Interior lighting ............................. 86 Turn light switch: § = off / daytime running lights 9 = sidelights / headlights Control indicator 8 3 74. Tail lights Tail lights are illuminated together with headlights and sidelights. To switch from low to high beam, push lever. To switch to low beam, pull lever. Headlight flash To activate the headlight flash, pull lever. 84 Lighting Headlight range adjustment Manual headlight range adjustment To adapt headlight range to the vehicle load to prevent dazzling: Press À or Á buttons until the required setting is displayed in the Driver Information Centre (DIC) 3 74. 0 = Front seats occupied 1 = All seats occupied 2 = All seats occupied and load compartment laden 3 = Driver's seat occupied and load compartment laden Headlights when driving abroad The asymmetrical headlight beam extends visibility at the edge of the road at the passenger side. However, when driving in countries where traffic drives on the opposite side of the road, adjust the headlights to prevent dazzling of oncoming traffic. Have the headlights adjusted by a workshop. Daytime running lights Daytime running lights increase visibility of the vehicle during daylight. When the function is activated and the ignition is switched on, the headlights come on automatically and instrument illumination is subdued. The light switch must be in position §. The daytime running lights switch off when the ignition is switched off. Note The driver remains responsible for switching on the low beam when required, e.g. when driving through a tunnel or at night. When the function is deactivated, the headlights do not come on automatically when the ignition is switched on and the light switch is in position §. The daytime running lights function is activated/deactivated via a menu in the Driver Information Centre (DIC) 3 74. Lighting Hazard warning flashers Turn and lane-change signals Switch the indicator off manually by moving the lever to its original position. Front fog lights Operated with the ¨ button. Lever up = right turn signal Lever down = left turn signal If the lever is moved past the resistance point, the turn signal is switched on constantly. When the steering wheel moves back, the turn signal is automatically deactivated. For five flashes, e.g. when changing lanes, press the lever until resistance is felt and then release. 85 Operated with the > button. Switching on front fog lights will switch sidelights on automatically. 86 Lighting Rear fog lights Misted light covers The inside of the light covers may mist up briefly in poor, wet and cold weather conditions, in heavy rain or after washing. The mist disappears quickly by itself; to help, switch on the headlights. Operated with the r button. The rear fog light can only be switched on when both the ignition and headlights or sidelights (with front fog lights) are on. Press the button again to turn the rear fog light off, or turn off the headlights and/or the front fog lights. Reversing lights The reversing lights come on when the ignition is on and reverse gear is selected. Interior lighting Instrument panel illumination control When driving at night with the low beam on, adjust the brightness of the vehicle's interior lighting (including instrument panel, climate control display etc.) via the settings menu of the Driver Information Centre (DIC) 3 74. To adjust brightness: Standard version of DIC 1. Press the SET ESC button once to access the settings menu. 2. Scroll through the menu options using the R or S buttons until menu option ILLU appears in the display. 3. Press the R or S button to increase or decrease the displayed value. 4. Press SET ESC briefly to confirm changes and automatically return to the previous display screen. Lighting Multifunction version of DIC 1. Press the SET ESC button to access the settings menu. 2. Scroll through the menu options using the R or S buttons until menu option LIGHTING appears in the display. 3. Press the R or S button to increase or decrease the displayed value. 4. Press SET ESC briefly to confirm changes and automatically return to the previous display screen. It is also possible to adjust the brightness using the R or S buttons without accessing the settings menu. Driver Information Centre (DIC) 3 74. Interior lights Depending on model variant, during entry and exit of the vehicle the front and rear courtesy lights come on automatically and then switch off after a delay. Note In the event of an accident of a certain severity, the interior lights come on automatically. Fuel cut-off system 3 80. 87 Front courtesy light with reading lights Front courtesy light Centre switch position: automatic interior light. To operate manually when the doors are closed, press the lens on either side. Centre switch position: automatic interior light. Can be operated individually or together with the 7 switch when the doors are closed. Press rocker switch 7 left or right to operate respective reading light. 88 Lighting Rear courtesy lights Removable rear courtesy light Centre switch position: automatic interior light. To operate manually when the doors are closed, press the lens on either side. Depending on model variant, the removable rear courtesy light may illuminate when the rear doors / tailgate or sliding side doors are opened and the central switch is in the middle position. Switch the light on permanently by pressing the top part of the central switch c. Switch the light off permanently by pressing the bottom part of the central switch (AUTO OFF). Load compartment lighting Depending on model variant, load compartment lighting switches on when the rear doors / tailgate or sliding side door is opened. To use as a handheld torch, press the button at the top of the lamp assembly (see illustration) to release it and pull torch down gently to remove. Press the switch on the end of the torch to turn the light on/off. Replace the torch in its original position to recharge the battery after use. Climate control Climate control Climate control systems ............... 89 Air vents ....................................... 92 Maintenance ................................ 93 Climate control systems Heating and ventilation system 89 Heating will not be fully effective until the engine has reached normal operating temperature. Fan speed Adjust the air flow by switching the fan to the desired speed. Air distribution to head area to head area and foot well to foot well to windscreen, front door windows and foot well V = to windscreen and front door windows M L K J = = = = Intermediate settings are possible. Controls for: ■ Temperature ■ Fan speed ■ Air distribution Heated rear window Ü 3 30. Temperature red = warm blue = cold Demisting and defrosting the windows ■ Set temperature control to warmest level. ■ Set fan speed to highest level. ■ Set air distribution control to V. ■ Switch on heated rear window Ü. 90 Climate control ■ Open side air vents as required and direct them towards door windows. ■ For simultaneous warming of the foot well, set air distribution control to J. Air conditioning system Cooling (AC) Operated with the AC button and functional only when the engine and fan are running. The air conditioning system cools and dehumidifies (dries) the air when outside temperature is a little above the freezing point. Therefore condensation may form and drip from under the vehicle. If no cooling or drying is required, switch the cooling system off to save fuel. Air recirculation system Operated with the 4 button. 9 Warning Additional to the heating and ventilation system, the air conditioning system has: AC = cooling 4 = air recirculation The exchange of fresh air is reduced in air recirculation mode. In operation without cooling the air humidity increases, so the windows may mist up. The quality of the passenger compartment air deteriorates, which may cause the vehicle occupants to feel drowsy. In warm and very humid ambient air conditions, the windscreen may mist up from outside, when cold air is directed towards it. If windscreen mists up from outside, activate windscreen wiper and deactivate V. Maximum cooling Briefly open the windows so that hot air can disperse quickly. ■ Cooling AC on. ■ Air recirculation system 4 on. ■ Set air distribution control to M. ■ Set temperature control to coldest level. ■ Set fan speed to highest level. ■ Open all air vents. Climate control Electronic climate control system Controls for: ■ Temperature ■ Air distribution and menu selection ■ Fan speed AUTO = Automatic mode = air recirculation 4 Ê = demisting and defrosting OFF = switch on/off Heated rear window Ü 3 30. 91 The preselected temperature is automatically regulated. In the automatic mode the fan speed and air distribution automatically regulate the air flow. The system can be manually adapted by use of air distribution and air flow controls. The electronic climate control system is only fully operational when the engine is running. For correct operation do not cover the sensor on the instrument panel. Heating will not be fully effective until the engine has reached normal operating temperature. When the minimum temperature is set below 16 ℃, the electronic climate control system runs at maximum cooling. LO appears in the display. If the maximum temperature is set above 32 ℃, the electronic climate control system runs at maximum heating. HI appears in the display. Automatic mode Fan speed Basic setting for maximum comfort: ■ Press AUTO button. ■ Open all air vents. ■ n on. ■ Set desired temperature. Temperature preselection Temperatures can be set to the desired value. For reasons of comfort, change temperature only in small increments. Turn AUTO knob to adjust. clockwise = warm anticlockwise = cold The selected fan speed is indicated with bars in the display. Press ] or < to increase or decrease the fan speed. maximum fan = all bars displayed speed minimum fan = one bar displayed speed Press n button to deactivate fan. To return to automatic fan speed: Press AUTO button. 92 Climate control Demisting and defrosting the windows Press the Ê button. Temperature and air distribution are set automatically and the fan runs at a high speed. When the vehicle reaches normal operating temperature the function remains active for approx. 3 minutes. To return to automatic mode: press button n or AUTO. Air distribution Press R, S and 6 buttons. LED in buttons illuminate. Arrows shown in the display indicate the distribution settings. Cooling The air conditioning system cools and dehumidifies (dries) when outside temperature is above a specific level. Therefore condensation may form and drip from under the vehicle. If no cooling or drying is required press n again to switch the cooling system off, thus saving fuel. Manual air recirculation mode Operated with the 4 button. recirculation = LED in button on illuminated; D appears in the display recirculation = LED in button off extinguishes; E appears in the display 9 Warning The exchange of fresh air is reduced in air recirculation mode. In operation without cooling the air humidity increases, so the windows may mist up. The quality of the passenger compartment air deteriorates, which may cause the vehicle occupants to feel drowsy. In warm and very humid ambient air conditions, the windscreen may mist up from outside, when cold air is directed towards it. If windscreen mists up from outside, activate windscreen wiper and deactivate V. Air vents Adjustable air vents At least one air vent must be open while cooling is on in order to prevent the evaporator from icing up due to lack of air movement. 9 Warning Do not attach any objects to the slats of the air vents. Risk of damage and injury in case of an accident. Centre air vents Climate control Slide knob to the left to open vent. Direct the flow of air by swivelling the vent. Slide knob to the right to close vent. Fixed air vents Additional air vents are located beneath the windscreen and door windows and in the foot wells. 93 Maintenance Air intake Side air vents Slide knob to the left to open vent. Direct the flow of air by swivelling the vent. Slide knob to the right to close vent. The air intake in front of the windscreen in the engine compartment must be kept clear to allow air intake. Remove any leaves, dirt or snow. Pollen filter The pollen filter cleans dust, soot, pollen and spores from the air entering the vehicle through the air intake. 94 Climate control Air conditioning regular operation In order to ensure continuously efficient performance, cooling must be operated for a few minutes once a month, irrespective of the weather and time of year. Operation with cooling is not possible when outside temperature is too low. Service For optimal cooling performance, it is recommended that the climate control system be checked annually, starting three years after initial vehicle registration, including: ■ Functionality and pressure test ■ Heating functionality ■ Leakage check ■ Check of drive belts ■ Cleaning of condenser and evaporator drainage ■ Performance check Driving and operating Driving and operating Driving hints ................................. 95 Starting and operating ................. 95 Engine exhaust ............................ 99 Manual transmission .................. 101 Manual transmission automated .................................. 101 Brakes ........................................ 105 Ride control systems ................. 107 Cruise control ............................. 108 Object detection systems ........... 109 Fuel ............................................ 111 Towing ....................................... 116 95 Driving hints Starting and operating Control of the vehicle New vehicle running-in Never coast with engine not running (except during Autostop) Many systems will not function in this situation (e.g. brake servo unit, power steering). Driving in this manner is a danger to yourself and others. All systems function during an Autostop, but there will be a controlled reduction in power steering assist and vehicle speed is reduced. Stop-start system 3 97. Pedals To ensure the pedal travel is uninhibited, there must be no mats in the area of the pedals. Do not brake unnecessarily hard for the first few journeys. During the first drive, smoke may occur because of wax and oil evaporating off the exhaust system. Park the vehicle in the open for a while after the first drive and avoid inhaling the fumes. During the running-in period fuel and engine oil consumption may be higher and the cleaning process of the diesel particle filter may take place more often. Autostop may be inhibited to allow for charging the battery. Diesel particle filter 3 99. 96 Driving and operating Ignition switch positions Starting the engine Starting the vehicle at low temperatures The start of the engine without additional heaters is possible down to -25 °С for diesel engines and -30 °C for petrol engines. Required is an engine oil with the correct viscosity, the correct fuel, performed services and a sufficiently charged battery. Turbo engine warm-up STOP = Steering wheel lock released, ignition off MAR = Ignition on, for diesel engine: preheating AVV = Starting Manual transmission: operate clutch. Do not operate the accelerator pedal. Diesel engine: turn the key to position MAR for preheating until control indicator ! extinguishes. Turn the key briefly to position AVV and release. Before restarting or to switch off the engine, turn the key back to position STOP. During an Autostop, the engine can be started by depressing the clutch pedal. Upon start-up, engine available torque may be limited for a short time, especially when the engine temperature is cold. The limitation is to allow the lubrication system to fully protect the engine. Vehicle shutdown Fuel cut-off system In the event of a collision of a certain severity, the fuel system is cut-off and the engine is switched off automatically, for safety reasons. A corresponding warning message may also appear in the Driver Information Centre (DIC) 3 74. Driving and operating Note In addition, the vehicle is automatically unlocked and the interior lights are illuminated. Turn the ignition key to position STOP to prevent battery discharge and seek the assistance of a workshop immediately. Have the vehicle checked for fuel leaks in the engine compartment, beneath the vehicle and near the fuel tank. To reset the fuel cut-off system and enable the vehicle to be driven: 1. Turn the ignition key to position MAR 3 96 2. Switch the right turn signal on and off again 3 85 3. Switch the left turn signal on and off again 4. Repeat switching the right turn signal on and off again 5. Repeat switching the left turn signal on and off again 6. Turn the ignition key to position STOP. 9 Danger If you can smell fuel in the vehicle, or a fuel leak is present, have the cause of this remedied immediately by a workshop. Do not reset the fuel cut-off system, to avoid the risk of fire. 97 A battery sensor ensures that an Autostop is only performed if the battery is sufficiently charged for a restart. Activation Fuel system messages 3 80. The stop-start system is available as soon as the engine is started, the vehicle starts-off and the conditions as stated below in this section are fulfilled. Overrun cut-off Deactivation The fuel supply is automatically cut off during overrun, i.e. when the vehicle is driven with a gear engaged but accelerator is released. Stop-start system The stop-start system helps to save fuel and to reduce exhaust emissions. When conditions allow, it switches off the engine as soon as the vehicle is at a low speed or at a standstill, e.g. at a traffic light or in a traffic jam. It starts the engine automatically as soon as the clutch is depressed. 98 Driving and operating Deactivate the stop-start system manually by pressing the ^ button in the centre console. LED in the button illuminates to confirm deactivation. Autostop If the vehicle is at a low speed or at a standstill, activate an Autostop as follows: ■ Depress the clutch pedal ■ set the lever to neutral ■ release the clutch pedal The engine will be switched off while the ignition stays on. An Autostop is indicated when ^ flashes in the Driver Information Centre (DIC) 3 74. Caution The steering assist can be reduced during an Autostop. Conditions for an Autostop The stop-start system checks if each of the following conditions is fulfilled. Otherwise an Autostop will be inhibited. ■ The stop-start system is not manually deactivated ■ the driver's door is closed or the driver's seat belt is fastened ■ the battery is sufficiently charged and in good condition ■ the engine is warmed up ■ the ambient temperature is not too low ■ the climate control system does not inhibit an Autostop ■ the self-cleaning function of the diesel particle filter is not active ■ the vehicle has moved since the last Autostop ■ the brake vacuum is sufficient ■ the windscreen wipers are operating at fast speed ■ reverse gear is selected Ambient temperature near to the freezing point can inhibit an Autostop. Certain settings of the climate control system may inhibit an Autostop. See Climate control chapter for more details. For manual transmission automated vehicles, an Autostop may be inhibited until a speed of approx. 10 km/h is reached. New vehicle running-in 3 95. Battery discharge protection To ensure reliable engine restarts, several battery discharge protection features are implemented as part of the stop-start system. Restart the engine Manual transmission Driving and operating The selector lever must be in neutral to enable an automatic restart. Depress the clutch pedal to restart the engine. Manual transmission automated If the lever is in position N, select another gear, otherwise release the brake pedal or move the lever to +, – or R. When one of the following conditions occurs during an Autostop, the engine will need to be restarted manually using the key. ■ the driver's seat belt is unfastened and the driver's door is opened ■ three minutes have elapsed since the engine was switched off If an electrical accessory, e.g. a portable CD player, is connected to the power outlet, a brief power drop during the restart may be noticeable. Parking ■ Do not park the vehicle on an easily ignitable surface. The high temperature of the exhaust system could ignite the surface. ■ Always apply parking brake. Apply manual parking brake without pressing release button. Apply as firmly as possible on downhill or uphill slopes. Depress the foot brake at the same time to reduce operating force. ■ Switch off the engine and ignition. Turn the steering wheel until the steering wheel lock engages. ■ If the vehicle is on a level surface or uphill slope, engage first gear. On an uphill slope, turn the front wheels away from the kerb. If the vehicle is on a downhill slope, engage reverse gear. Turn the front wheels towards the kerb. ■ Lock the vehicle. 99 Engine exhaust 9 Danger Engine exhaust gases contain poisonous carbon monoxide, which is colourless and odourless and could be fatal if inhaled. If exhaust gases enter the interior of the vehicle, open the windows. Have the cause of the fault rectified by a workshop. Avoid driving with an open load compartment, otherwise exhaust gases could enter the vehicle. Diesel particle filter The diesel particle filter system filters harmful soot particles out of the exhaust gases. The system includes a self-cleaning function that runs automatically during driving without any notification. The filter is cleaned by periodically burning off the soot particles at high temperature. This process takes place automatically under set driving conditions and may 100 Driving and operating take up to 25 minutes. Typically it needs 15 minutes. Autostop is not available and fuel consumption may be higher during this period. The emission of smells and smoke during this process is normal. Under certain driving conditions, e.g. short distances, the system cannot clean itself automatically. If the cleaning of the filter is required and if previous driving conditions did not enable automatic cleaning, it will be indicated by control indicator [. Simultaneously a message may appear in the Driver Information Centre (DIC) 3 74. [ illuminates when diesel particle filter is full. Start cleaning process as soon as possible to avoid damage to the engine. Cleaning process To activate cleaning process, continue driving, keep engine speed above 2000 rpm. Shift down if necessary. Diesel particle filter cleaning is then started. Caution If the cleaning process is interrupted, there is a risk of provoking severe engine damage. Cleaning takes place quickest at high engine speeds and loads. The control indicator [ extinguishes as soon as the self-cleaning operation is complete. Catalytic converter The catalytic converter reduces the amount of harmful substances in the exhaust gases. Caution Fuel grades other than those listed on pages 3 111, 3 157 could damage the catalytic converter or electronic components. Unburnt petrol will overheat and damage the catalytic converter. Therefore avoid excessive use of the starter, running the fuel tank dry and starting the engine by pushing or towing. In the event of misfiring, uneven engine running, a reduction in engine performance or other unusual problems, have the cause of the fault rectified by a workshop as soon as possible. In an emergency, driving can be continued for a short period, keeping vehicle speed and engine speed low. Driving and operating Manual transmission Caution It is not advisable to drive with the hand resting on the selector lever. When gearshifting is recommended to improve fuel economy, control indicator [ or Ò illuminates in the Driver Information Centre (DIC) 3 70. 101 Manual transmission automated The manual transmission automated (MTA) permits manual (manual mode) or automatic gear shifting (automatic mode), both with automatic clutch control. Transmission display To engage reverse, with the vehicle stationary, wait 3 seconds after depressing the clutch pedal, pull up the collar on the selector lever and engage the gear. If the gear does not engage, set the lever to neutral, release the clutch pedal and depress again; then repeat gear selection. Do not grind the clutch unnecessarily. When operating, depress the clutch pedal completely. Do not use the pedal as a foot rest. Shows the mode and current gear. 102 Driving and operating Starting the engine Selector lever Depress the foot brake when starting the engine. If the foot brake is not depressed, a warning message appears in the Driver Information Centre (DIC) in conjuction with a warning chime 3 80 and the engine cannot be started. Note The volume of the warning chime can also be adjusted via the DIC. Driver Information Centre (DIC) 3 74. When the foot brake is depressed, the transmission automatically shifts to N (neutral) and the engine can be started. There may be a slight delay. R + - = Reverse gear. Engage only when vehicle is stationary. The transmission display shows "R" when reverse gear is engaged. = Shift to a higher gear. = Shift to a lower gear. Starting off Always move the selector lever in the appropriate direction as far as it will go. Upon release, it automatically returns to the centre position. N = Neutral. = Drive position. o A/M = Switch between automatic and manual mode. The transmission display shows AUTO when in automatic mode. When the engine is started, depress the foot brake and move the selector lever towards + to engage first gear. Shift to a higher or lower gear by moving selector lever to + or -. Gears can be skipped by moving the selector lever repeatedly at short intervals. The driver will be alerted to an incorrect gear selection by an audible warning chime in conjunction with a message in the Driver Information Centre (DIC) 3 74. The system will downshift, selecting the most appropriate gear automatically. If R is selected, reverse gear is engaged. The vehicle starts to move when the foot brake is released. To Driving and operating start off quickly, release the foot brake and accelerate immediately after engaging a gear. Move the selector lever towards A/M to engage automatic mode; the transmission shifts to other gears automatically, dependent on driving conditions. To engage manual mode, move the selector lever towards A/M. The current gear will appear in the transmission display. Stopping the vehicle In automatic or manual mode, first gear is engaged and the clutch is released when the vehicle is stopped. In R, reverse gear remains engaged. When stopping on gradients, engage parking brake or depress the foot brake. To prevent overheating of the clutch, an intermittent audible warning chime may sound as a signal to depress the foot brake or apply the parking brake. Switch off engine if stopping for a lengthy period, e.g. in traffic jams. When the vehicle is parked and the driver's door is opened, a warning chime will sound if neutral is not selected or the foot brake has not been depressed. Engine braking Automatic mode When driving downhill, the manual transmission automated does not shift into higher gears until a fairly high engine speed has been reached. It shifts down in good time when braking. Manual mode To utilise the engine braking effect, select a lower gear in good time when driving downhill. 103 Rocking the vehicle Rocking the vehicle is only permissible if the vehicle is stuck in sand, mud, snow or a hole. Move the selector lever between R and A/M (or between + and -) in a repeat pattern, while applying light pressure to the accelerator pedal. Do not race the engine and avoid sudden acceleration. Parking Apply the parking brake. The most recently engaged gear (see transmission display) remains engaged. With N, no gear is engaged. When the ignition is switched off, the transmission no longer responds to movement of the selector lever. If the ignition is not switched off, or the parking brake has not been applied, a warning chime will sound upon opening the driver's door. 104 Driving and operating Manual mode If engine speed is too low, the transmission automatically shifts to a lower gear. In manual mode, no automatic shifting to a higher gear takes place at high engine revolutions. If engine speed is too high, the transmission only switches to a higher gear via kickdown. Kickdown 3 104. Electronic driving programmes Eco mode E When automatic mode is engaged, the Eco mode can be selected to reduce fuel consumption. Eco mode selects the most suitable gear depending on the speed of the vehicle, the engine speed and the intensity with which the accelerator is pressed. Activation Press the E button on the selector lever housing. Control indicator E is shown in the transmission display to indicate activation. Deactivation Eco mode is switched off by: ■ pressing the E button again, ■ switching to manual mode. In order to protect the transmission at extremely high clutch temperatures, an intermittent audible warning chime may sound. In such cases, depress the foot brake, select "N" and apply the parking brake to allow the clutch to cool down. Kickdown If the accelerator pedal is pressed past the pressure point, the transmission shifts to a lower gear depending on engine speed. Full engine power is available for acceleration. Driving and operating If engine speed is too high the transmission switches to a higher gear, even in manual mode. Without kickdown this automatic shift is not effected in manual mode. Fault In the event of a fault, control indicator Ñ is shown in the transmission display. Continued driving is possible, provided the vehicle is driven with care and anticipation. A warning message may appear in the Driver Information Centre (DIC) in conjunction with a warning chime 3 80. Note The volume of the warning chime can also be adjusted via the DIC. Driver Information Centre (DIC) 3 74. Have the cause of the fault remedied by a workshop. Brakes The brake system comprises two independent brake circuits. If a brake circuit fails, the vehicle can still be braked using the other brake circuit. However, braking effect is achieved only when the brake pedal is depressed firmly. Considerably more force is needed for this. The braking distance is extended. Seek the assistance of a workshop before continuing your journey. When the engine is not running, the support of the brake servo unit disappears once the brake pedal has been depressed once or twice. Braking effect is not reduced, but braking requires significantly greater force. It is especially important to bear this in mind when being towed. Control indicator R 3 70. Antilock brake system Antilock brake system (ABS) prevents the wheels from locking. 105 ABS starts to regulate brake pressure as soon as a wheel shows a tendency to lock. The vehicle remains steerable, even during hard braking. ABS control is made apparent through a pulse in the brake pedal and the noise of the regulation process. For optimum braking, keep the brake pedal fully depressed throughout the braking process, despite the fact that the pedal is pulsating. Do not reduce the pressure on the pedal. After starting off the system performs a self-test which may be audible. Control indicator u 3 70. Fault 9 Warning If there is a fault in the ABS, the wheels may be liable to lock due to braking that is heavier than normal. The advantages of ABS are no longer available. During 106 Driving and operating hard braking, the vehicle can no longer be steered and may swerve. Have the cause of the fault remedied by a workshop. Parking brake Manual parking brake To release the parking brake, pull the lever up slightly, press the release button and fully lower the lever. To reduce the operating forces of the parking brake, depress the foot brake at the same time. A warning chime will sound if a certain speed is exceeded with the parking brake applied. Note The volume of the warning chime can also be adjusted via the DIC. Driver Information Centre (DIC) 3 74. Control indicator R 3 70. Brake assist Always apply parking brake firmly without operating the release button, and apply as firmly as possible on a downhill or uphill slope. If the brake pedal is depressed quickly and forcefully, maximum brake force is automatically applied (full braking). Maintain steady pressure on the brake pedal for as long as full braking is required. Maximum brake force is automatically reduced when the brake pedal is released. Hill start assist The system helps prevent unintended movement when driving away on inclines. When releasing the foot brake after stopping on an incline, the brakes remain on for a further two seconds. The brakes release automatically as soon as the vehicle begins to accelerate. If control indicator Z illuminates while driving, there is a fault in the Hill start assist 3 70. Seek the assistance of a workshop to have the fault remedied. Driving and operating Ride control systems Traction Control system The Anti-Slip Regulator (ASR) is a component of the Electronic Stability Control system. ASR improves driving stability when necessary, regardless of the type of road surface or tyre grip, by preventing the drive wheels from spinning. As soon as the drive wheels starts to spin, engine output is reduced and the wheel spinning the most is braked individually. This considerably improves the driving stability of the vehicle on slippery road surfaces. ASR is operational as soon as the control indicator x extinguishes. When ASR is active x flashes. 9 Warning Do not let this special safety feature tempt you into taking risks when driving. Adapt speed to the road conditions. Deactivation 107 ASR is reactivated by pressing the ASR OFF button again. ASR is also reactivated the next time the ignition is switched on. Fault ASR will switch off automatically in the event of a fault. Control indicator x will illuminate in the instrument cluster in conjunction with a message in the Driver Information Centre (DIC) 3 74. Seek the assistance of a workshop. Control indicator x 3 71. Electronic stability program ASR can be switched off when spinning of drive wheels is required: press button ASR OFF briefly. LED in button illuminates and a message appears in the driver information centre. Electronic Stability Program (ESP) improves driving stability when necessary, regardless of the type of road surface or tyre grip. It also prevents the drive wheels from spinning. As soon as the vehicle starts to swerve (understeer/oversteer), engine output is reduced and the wheels are braked individually. This 108 Driving and operating considerably improves the driving stability of the vehicle on slippery road surfaces. ESP is operational as soon as control indicator x extinguishes. When ESP comes into action x flashes. The ESP system is automatically activated when the vehicle is started and cannot be deactivated Seek the assistance of a workshop. Control indicator x 3 71. Cruise control The cruise control can store and maintain speeds above approx. 30 km/h. Deviations from the stored speeds may occur when driving uphill or downhill. 9 Warning Do not let this special safety feature tempt you into taking risks when driving. Adapt speed to the road conditions. Fault In the event of a fault, the ESP will be automatically switched off and control indicator x will illuminate in the instrument cluster in conjunction with a message in the Driver Information Centre (DIC) 3 74. The LED in the ASR OFF button will also illuminate. Do not use the cruise control if it is not advisable to maintain a constant speed. Control indicator m 3 74. Driving and operating Switching on Turn end of lever ON, control indicator m illuminates in the instrument cluster in conjunction with a message in the driver information centre. Reduce speed With cruise control active, push lever downwards - or briefly push lever downwards - repeatedly: speed decreases continuously or in small increments. Activation Deactivation Increase speed Resume stored speed Accelerate to the desired speed and push lever upwards +, the current speed is stored and maintained. Accelerator pedal can be released. Vehicle speed can be increased by depressing the accelerator pedal. When the accelerator pedal is released, the previously stored speed is resumed. With cruise control active, push lever upwards + or briefly push lever upwards + repeatedly: speed increases continuously or in small increments. Alternatively accelerate to the desired speed and store by pushing lever upwards +. 109 Object detection systems Parking assist Automatic deactivation: ■ vehicle speed below approx. 30 km/h, ■ the brake pedal is depressed, ■ the clutch pedal is depressed, ■ the Traction Control system or Electronic Stability Control is operating. Press button = at a speed above 30 km/h. The stored speed will be obtained. Switching off Turn end of lever OFF, control indicator m extinguishes. The stored speed is deleted. Switching off the ignition also deletes the stored speed. The parking assist makes parking easier by measuring the distance between the vehicle and obstacles, and giving acoustic signals. It is the driver, however, who bears full responsibility for the parking manoeuvre. The system consists of four ultrasonic parking sensors in the rear bumper. Control indicator r 3 71. 110 Driving and operating System operation The parking assist is turned on automatically when reverse gear is engaged. The intervals between the beeps become shorter as the vehicle gets closer to the obstacle. When the distance is less than 30 cm, the beeping is a continuous tone which stops immediately when the distance is increased. Fault In the event of a fault in the system, r illuminates and a message is displayed in the Driver Information Centre (DIC) 3 74. The following conditions could affect the system's performance: ■ The ultrasonic sensors are not clean. Keep the bumper free of mud, dirt, snow, ice and slush. ■ The sensors are covered by frost or ice. ■ The rear doors / tailgate are open. ■ An object was hanging out of the rear doors / tailgate during the last drive cycle. Once the object has been removed, the parking assist will return to normal operation. ■ An object or cover is attached to the rear of the vehicle. ■ The bumper is damaged. Take the vehicle to a workshop to repair the system. ■ Other conditions, such as vibrations from a jackhammer, are affecting system performance. In the event the system still does not work properly, seek the assistance of a workshop. A warning chime is also sounded briefly if a fault is present when reverse gear is engaged 3 80. Note The volume of the warning chime can also be adjusted via the DIC. Driver Information Centre (DIC) 3 74. Important hints for using the parking assist systems 9 Warning Under certain circumstances, various reflective surfaces on objects or clothing as well as external noise sources may cause the system to fail to detect obstacles. Special attention has to be paid to low obstacles which can damage the lower part of the bumper. If such obstacles leave the detection area of the sensors during approach of the vehicle, a continuous warning tone will sound. Driving and operating Caution Performance of the sensor can be reduced when sensors are covered, e.g. by ice or snow. Performance of the parking assist systems can be reduced due to heavy loading. Special conditions apply if there are taller vehicles involved (e.g. off-road vehicles, mini vans, vans). Object identification in the upper part of these vehicles cannot be guaranteed. Objects with a very small reflection cross section, like objects of narrow size or soft materials, may not be detected by the system. Parking assist will not avoid a collision with objects which are out of the detection range of the sensors. Note The parking assist system automatically detects factory-fitted towing equipment. It is deactivated when the connector is plugged in. The sensor may detect a nonexistent object (echo disturbance) caused by external acoustic or mechanical disturbances. 111 Fuel Fuel for petrol engines Only use unleaded fuel that complies with European standard EN 228 or E DIN 51626-1 or equivalent. Your engine is capable of running with E10 fuel that fulfills these standards. E10 fuel contains up to 10 % bioethanol. Use fuel with the recommended octane rating 3 157. Use of fuel with too low an octane rating can reduce engine power and torque and slightly increases fuel consumption. Caution Do not use fuel or fuel additives that contain metallic compounds such as manganese-based additives. This may cause engine damage. 112 Driving and operating Caution Caution Use of fuel that does not comply to EN 228 or E DIN 51626-1 or equivalent can lead to deposits or engine damage and may affect your warranty. Use of fuel that does not comply to EN 590 or similar can lead to engine powerloss, increased wear or engine damage and may affect your warranty. Caution Use of fuel with too low an octane rating could lead to uncontrolled combustion and engine damage. Fuel for diesel engines Only use diesel fuel that complies with EN 590. In countries outside the European Union use Euro-Diesel fuel with a sulphur concentration below 50 ppm. Fuel selector Do not use marine diesel oils, heating oils, Aquazole and similar dieselwater emulsions. Diesel fuels must not be diluted with fuels for petrol engines. Fuel for natural gas operation Use natural gas with a methane content of approx. 78 - 99 %. L-gas (low) has approx. 78 - 87 % and H-gas (high) has approx. 87 - 99 %. Biogas with the same methane content can also be used if it has been chemically prepared and desulphurised. Only use natural gas or biogas that complies with DIN 51624. Liquid gas or LPG must not be used. Pressing button Y in the centre console switches between petrol and natural gas operation. The LED 1 status shows the current operating mode. 1 off = natural gas operation. 1 illuminates = petrol operation. As soon as the natural gas tanks are empty, petrol operation is automatically engaged. Control indicator Y illuminates in the Driver Information Centre (DIC) 3 74 until the ignition is switched off. Driving and operating A slight loss of power and torque can be expected in petrol operation. You must therefore adapt your driving style (e.g. during overtaking manoeuvres) and vehicle loads (e.g. towing loads) accordingly. Every six months run the petrol tank down until control indicator § illuminates and then refuel. This is necessary to maintain fuel quality as well as system function necessary for petrol operation. Fill the tank completely at regular intervals to prevent corrosion in the tank. Refuelling Fuel filler flap is located at left rear side of vehicle. 9 Danger Before refuelling, switch off engine and any external heaters with combustion chambers. Switch off any mobile phones. Follow the operating and safety instructions of the filling station when refuelling. 9 Danger Fuel is flammable and explosive. No smoking. No naked flames or sparks. If you can smell fuel in your vehicle, have the cause of this remedied immediately by a workshop. 113 Caution To avoid damage, do not attempt to operate the sliding side door when the fuel filler flap is open. Note Depending on model, the sliding side door may be fitted with a safety system that prevents the door from being opened fully when the fuel filler flap is open. Sliding side door 3 22. Caution In case of misfuelling, do not switch on ignition. Release the fuel filler flap by pulling the flap by hand. Insert key into fuel filler cap and turn anticlockwise to unlock. To remove fuel filler cap, rotate anticlockwise. The fuel filler cap can be retained in the bracket on the fuel filler flap. 114 Driving and operating To refuel, fully insert the pump nozzle and switch it on. After the automatic cut-off, the fuel tank can be topped up with a maximum of two doses of fuel. Natural gas refuelling Caution Wipe off any overflowing fuel immediately. To close, replace fuel filler cap and turn clockwise. Insert key into fuel filler cap and turn clockwise to lock, then remove key. Close the fuel filler flap. The capacity of the natural gas tank depends on outside temperature, filling pressure and type of refuelling system. Close the fuel filler flap after refuelling. Terms for "natural gas vehicles" abroad: German Erdgasfahrzeuge English NGVs = Natural Gas Vehi‐ cles Open the fuel filler flap. 9 Warning Refuel only with a maximum output pressure of 250 bar. Use only temperature compensated filling stations. The refuelling procedure must be completed, i.e. the filler neck must be vented. French Véhicules au gaz naturel – or – Véhicules GNV Italian Metano auto Terms for "natural gas" abroad: Driving and operating German Erdgas English CNG = Compressed Natural Gas French GNV = Gaz Naturel (pour) Véhicules - or CGN = carburantgaz naturel Italian Metano (per auto) Fuel filler cap Only use genuine fuel filler caps. Diesel-engined vehicles have special fuel filler caps. Fuel cut-off system In the event of a collision of a certain severity, the fuel system is cut-off and the engine is switched off automatically, for safety reasons. Resetting the fuel cut-off system; refer to "Fuel system messages" 3 80. Fuel consumption - CO2Emissions The fuel consumption (combined) of the Opel Combo is within a range of 4.8 to 7.7 l/100 km. The CO2 emission (combined) is within a range of 126 to 179 g/km. For the values specific to your vehicle, refer to the EEC Certificate of Conformity provided with your vehicle or other national registration documents. General information The official fuel consumption and specific CO2 emission figures quoted relate to the EU base model with standard equipment. Fuel consumption data and CO2 emission data are determined according to regulation R (EC) No. 715/2007 (in the applicable version), taking into consideration the vehicle weight in running order, as specified by the regulation. 115 The figures are provided only for the purpose of comparison between different vehicle variants and must not be taken as a guarantee for the actual fuel consumption of a particular vehicle. Additional equipment may result in slightly higher results than the stated fuel consumption and CO2 figures. Furthermore, fuel consumption is dependent on personal driving style as well as road and traffic conditions. Natural gas The fuel consumption information was obtained using reference fuel G20 (methane proportion 99 - 100 mol%) under prescribed driving conditions. When using natural gas with a lower proportion of methane, the fuel consumption can differ from the specified values. 116 Driving and operating Towing General information Only use towing equipment that has been approved for your vehicle. Vehicles with natural gas engine may require special towing equipment. Entrust retrofitting of towing equipment to a workshop. It may be necessary to make changes that affect the cooling system, heat shields or other equipment. Fitting of towing equipment could cover the opening of the towing eye. If this is the case use the coupling ball bar for towing. Always keep the coupling ball bar in the vehicle. Driving characteristics and towing tips Before attaching a trailer, lubricate the coupling ball. However, do not do so if a stabiliser, which acts on the coupling ball, is being used to reduce snaking movements. For trailers with low driving stability and caravan trailers with a permitted gross vehicle weight of more than 1300 kg the use of a stabiliser is strongly recommended when driving above 80 km/h. If the trailer starts snaking, drive more slowly, do not attempt to correct the steering and brake sharply if necessary. When driving downhill, drive in the same gear as if driving uphill and drive at a similar speed. Adjust tyre pressure to the value specified for full load 3 167. Trailer towing Trailer loads The permissible trailer loads are vehicle and engine-dependent maximum values which must not be exceeded. The actual trailer load is the difference between the actual gross weight of the trailer and the actual coupling socket load with the trailer coupled. The permissible trailer loads are specified in the vehicle documents. In general, they are valid for gradients up to max. 12 %. The permitted trailer load applies up to the specified incline and up to an altitude of 1000 metres above sea level. Since engine power decreases as altitude increases due to the air becoming thinner, therefore reducing climbing ability, the permissible gross train weight also decreases by 10 % for every 1000 metres of additional altitude. The gross train weight does not have to be reduced when driving on roads with slight inclines (less than 8 %, e.g. motorways). The permissible gross train weight must not be exceeded. This weight is specified on the identification plate 3 154. Vertical coupling load The vertical coupling load is the load exerted by the trailer on the coupling ball. It can be varied by changing the weight distribution when loading the trailer. Driving and operating The maximum permissible vertical coupling load (75 kg) is specified on the towing equipment identification plate and in the vehicle documents. Always aim for the maximum load, especially in the case of heavy trailers. The vertical coupling load should never fall below 25 kg. Rear axle load The permissible axle loads (see identification plate or vehicle documents) must not be exceeded. 117 118 Vehicle care Vehicle care General Information ................... 118 Vehicle checks ........................... 119 Bulb replacement ....................... 125 Electrical system ........................ 131 Vehicle tools .............................. 134 Wheels and tyres ....................... 135 Jump starting ............................. 144 Towing ....................................... 146 Appearance care ....................... 147 General Information Vehicle storage Accessories and vehicle modifications Storage for a long period of time We recommend the use of genuine parts and accessories and factory approved parts specific for your vehicle type. We cannot assess or guarantee reliability of other products - even if they have a regulatory or otherwise granted approval. Do not make any modifications to the electrical system, e.g. changes of electronic control units (chip tuning). Caution When transporting the vehicle on a train or on a recovery vehicle, the mud flaps might be damaged. If the vehicle is to be stored for several months: ■ Wash and wax the vehicle. ■ Have the wax in the engine compartment and underbody checked. ■ Clean and preserve the rubber seals. ■ Fill up fuel tank completely. ■ Change the engine oil. ■ Drain the washer fluid reservoir. ■ Check the coolant antifreeze and corrosion protection. ■ Adjust tyre pressure to the value specified for full load. ■ Park the vehicle in a dry, well ventilated place. Engage first or reverse gear to prevent the vehicle from rolling. ■ Do not apply the parking brake. Vehicle care ■ Open the bonnet, close all doors and lock the vehicle. ■ Disconnect the clamp from the negative terminal of the vehicle battery. Beware that all systems are not functional, e.g. anti-theft locking system. Putting back into operation When the vehicle is to be put back into operation: ■ Connect the clamp to the negative terminal of the vehicle battery. Activate the electronics of the power windows. ■ Check tyre pressure. ■ Fill up the washer fluid reservoir. ■ Check the engine oil level. ■ Check the coolant level. ■ Fit the number plates if necessary. End-of-life vehicle recovery Information on end-of-life vehicle recovery centres and the recycling of end-of-life vehicles is available on our website. Only entrust this work to an authorised recycling centre. Natural gas vehicles must be recycled by a service centre authorised for natural gas vehicles. 119 Vehicle checks Performing work 9 Warning Only perform engine compartment checks when the ignition is off. The cooling fan may start operating even if the ignition is off. 120 Vehicle care Closing 9 Danger Lower the bonnet and allow it to drop into the catch. Check that the bonnet is engaged. The ignition system uses extremely high voltage. Do not touch. Engine oil Bonnet Opening Push the safety catch and open the bonnet. Pull the release lever and return it to its original position. Secure the bonnet support. Check the engine oil level manually on a regular basis to prevent damage to the engine. Ensure that the correct specification of oil is used. Recommended fluids and lubricants 3 152. Check with the vehicle on a level surface. The engine must be at operating temperature and switched off for at least 5 minutes. Pull out the dipstick, wipe it clean, insert it to the stop on the handle, pull out and read the engine oil level. Insert dipstick to the stop on the handle and make half a turn. Vehicle care We recommend the use of the same grade of engine oil that was used at last change. The engine oil level must not exceed the MAX mark on the dipstick. Caution 121 Coolant level Caution Too low a coolant level can cause engine damage. Overfilled engine oil must be drained or suctioned out. When the engine oil level has dropped to the MIN mark, top up engine oil. Capacities 3 166. Fit the cap on straight and tighten it. Engine coolant The coolant provides freeze protection down to approx. -28 °C. In northern countries with very low temperatures, the factory filled coolant provides frost protection down to approx. -37°C. Caution Only use approved antifreeze. If the cooling system is cold, the coolant level should be between the MIN and MAX mark. Top up if the level is low. 122 Vehicle care 9 Warning Power steering fluid Washer fluid If the fluid level in the reservoir falls below the MIN mark consult a workshop. Fill with clean water mixed with a suitable quantity of windscreen washer fluid which contains antifreeze. Allow the engine to cool before opening the cap. Carefully open the cap, relieving the pressure slowly. To top up use a 1:1 mixture of released coolant concentrate mixed with clean tap water. If no coolant concentrate is available, use clean tap water. Install the cap tightly. Have the coolant concentration checked and have the cause of the coolant loss remedied by a workshop. Caution Only washer fluid with a sufficient antifreeze concentration provides protection at low temperatures or a sudden drop in temperature. Vehicle care 123 Brakes Battery A squealing noise, or illumination of brake pad wear control indicator F indicates that the brake lining is at its minimum thickness. Continued driving is possible but have the brake linings replaced as soon as possible. Once new brake linings are installed, do not brake unnecessarily hard for the first few journeys. Brake pad wear indicator F 3 70. The vehicle battery is maintenancefree provided that the driving profile allows sufficient charging of the battery. Short-distance-driving and frequent engine starts can discharge the battery. Avoid the use of unnecessary electrical consumers. Brake fluid 9 Warning Brake fluid is poisonous and corrosive. Avoid contact with eyes, skin, fabrics and painted surfaces. The brake fluid level must be between the MIN and MAX marks. When topping up, ensure maximum cleanliness as contamination of the brake fluid can lead to brake system malfunctions. Have the cause of the loss of brake fluid remedied by a workshop. Only use high-performance brake fluid approved for the vehicle. Brake and clutch fluid 3 152. Batteries do not belong in household waste. They must be disposed of at an appropriate recycling collection point. Laying up the vehicle for more than 4 weeks can lead to battery discharge. Disconnect the clamp from the negative terminal of the vehicle battery. Ensure the ignition is switched off before connecting or disconnecting the vehicle battery. 124 Vehicle care Replacing the battery Note Any deviation from the instructions given in this paragraph may lead to a temporary deactivation of the stopstart system. Wiper blade replacement Wiper blade on rear swing door Lift the wiper arm until it stays in the raised position, press button to disengage the wiper blade and remove. Attach the wiper blade slightly angled to the wiper arm and push until it engages. Lower wiper arm carefully. Lift wiper arm, press and hold retaining clip and detach wiper blade. Attach the wiper blade slightly angled to the wiper arm and push until it engages. Lower wiper arm carefully. In vehicles with stop-start system, ensure to have the correct battery replaced. We recommend that you have the battery replaced by a workshop. Stop-start system 3 97. Charging the battery 9 Warning On vehicles with stop-start system, ensure that the charging potential does not exceed 14.6 volts when using a battery charger. Otherwise the battery might be damaged. Jump starting 3 144. Vehicle care Wiper blade on tailgate Bulb replacement Switch off the ignition and switch off the relevant switch or close the doors. Only hold a new bulb at the base! Do not touch the bulb glass with bare hands. Use only the same bulb type for replacement. Replace headlight bulbs from within the engine compartment. Lift wiper arm, press retaining clips to detach wiper blade. Attach the wiper blade to the wiper arm and push until it engages. Lower wiper arm carefully. Halogen headlights 125 Headlights have separate systems for low beam/side light 1 (outer bulb), high beam/daytime running light 2 (inner bulb). To access bulbs, pull off protective covers. Low beam 1. Remove protective cover. 2. Detach connector from bulb. 3. Disengage wire clip and remove bulb from reflector. 4. Insert new bulb in reflector so that the locating tab of the bulb aligns with the reflector recess. 126 Vehicle care 5. Attach connector to bulb. 6. Engage wire clip. 7. Install protective cover. High beam 1. Remove protective cover. 2. Detach connector from bulb. 3. Disengage wire clip and remove bulb from reflector. 4. Insert new bulb in reflector so that the bulb aligns with the reflector recess. 5. Engage wire clip, plug connector onto bulb. 6. Install protective cover. Daytime running light 1. Remove protective cover. Side light 1. Remove protective cover. Withdraw sidelight bulb holder from reflector by turning anticlockwise. 2. Remove bulb from socket, insert new bulb. 3. Insert bulb holder in reflector. 4. Rotate clockwise to engage. 5. Install protective cover. 2. Withdraw sidelight bulb holder from reflector by turning anticlockwise. 3. Remove bulb from socket, insert new bulb. 4. Insert bulb holder in reflector. 5. Rotate clockwise to engage. 6. Install protective cover. Front turn signal light 1. Remove protective cover. Vehicle care 127 Tail lights 2. Withdraw bulb holder from reflector by turning anticlockwise. 3. Push bulb into holder slightly, rotate anticlockwise, remove and renew bulb. 4. Insert bulb holder in reflector. 5. Rotate clockwise to engage. 6. Install protective cover. 1. Remove three retaining screws. 2. Remove light housing from vehicle. 3. Disengage connector plug from bulb holder. 4. Unscrew the four retaining screws using a screwdriver. Turn bulb holder for reverse light anticlockwise and replace bulb. 5. Remove bulb holder and seal from light housing. 6. Push bulb into socket slightly, rotate anti-clockwise, remove and renew bulb. 128 Vehicle care 9. Engage connector plug. 10. Insert light housing in body, ensuring proper positioning. Tighten three retaining screws. Number plate light Tailgate Side turn signal lights Have bulbs replaced by a workshop. Brake light (1) Turn signal light (2) Tail light (3) Tail light/fog light (4) 7. Install seal on bulb holder ensuring it is fitted correctly. Install bulb holder in light housing ensuring that it engages properly. Tighten four retaining screws using a screw driver. 8. Install reverse light bulb holder and turn clockwise to tighten. Centre high-mounted brake light Have bulbs replaced by a workshop. 1. Insert screwdriver as indicated by the arrows, press to the side and release the bulb housing. Vehicle care Back doors 129 Interior lights Front and rear courtesy light 2. Turn the bulb holder anticlockwise to remove from the bulb housing. Remove the bulb by pulling. 3. Replace the bulb. 4. Insert bulb holder in bulb housing and rotate clockwise 5. Install the bulb housing ensuring it engages correctly. 1. Insert screwdriver as indicated by the arrows, press to the left and release the bulb housing. 2. Press bulb slightly towards spring clip and remove. 3. Replace the bulb. 4. Install the bulb housing ensuring it engages correctly. 1. Remove lens using a flat blade screwdriver. 2. Open the rear cover. 3. Renew bulb. 4. Close rear cover. 5. Reinstall lens. 130 Vehicle care Front courtesy light, reading lights Removable rear courtesy light 2. Prise the lamp assembly out with a flat blade screwdriver at the points illustrated. 3. Renew bulb. 4. Reinstall lamp assembly. Instrument panel illumination Have bulbs replaced by a workshop. 1. Remove lens using a flat blade screwdriver. 2. Open the rear cover. 3. Renew bulbs. 4. Close rear cover. 5. Reinstall lens. 1. Press the button at the top of the lamp assembly to release it and pull down gently to remove. Vehicle care Electrical system Fuses Data on the replacement fuse must match the data on the defective fuse. There are two fuse boxes in the vehicle: ■ on the right of the engine compartment, next to the battery ■ behind a cover on the lower part of the instrument panel, on the driver's side Before replacing a fuse, turn off the respective switch and the ignition. A blown fuse can be recognised by its melted wire. Do not replace the fuse until the cause of the fault has been remedied. Some functions are protected by several fuses. Fuses may also be inserted without existence of a function. Fuse extractor Use a fuse extractor to remove fuses. 131 132 Vehicle care Engine compartment fuse box Place the fuse extractor on the various types of fuse from the top or side, and withdraw fuse. The fuse box is on the right of the engine compartment, next to the battery. To remove the protective cover and access the fuses, remove the two screws (see illustration). Vehicle care No. Circuit Instrument panel fuse box F09 Rear door switch F10 Horn F14 High beam F15 PTCI heater F19 Air conditioning system F20 Heated rear window F21 Fuel pump F30 Fog lights F84 CNG system F85 Power outlets F86 Cigarette lighter, heated seats F87 Stop-start system F88 Mirror heating After having changed defective fuses refit the fuse box cover. If the fuse box cover is not closed correctly, malfunction may occur. The fuse box is located behind a cover on the lower part of the instrument panel, on the driver's side. 133 134 Vehicle care No. Circuit No. Circuit Vehicle tools F12 Right low beam F53 Instrument panel F13 Left low beam, headlight range adjustment F94 Power outlet load compartment Tools F31 Fusebox relays, body control unit relays F32 Courtesy lights F36 Diagnostic connector, climate control system, Infotainment system F95 Cigarette lighter, power outlet Van F96 Cigarette lighter, power outlet F97 Heated front seat F98 Heated front seat F37 Instrument panel, braking system F38 Central locking system F43 Windscreen washer system F47 Power windows F48 Power windows F49 Exterior mirrors, Infotainment system, parking assist F51 Infotainment system, braking system, clutch The tools and the vehicle jacking equipment are in the storage area behind the front seat. Vehicle care Combo Tour Wheels and tyres Tyre condition, wheel condition Drive over edges slowly and at right angles if possible. Driving over sharp edges can cause tyre and wheel damage. Do not trap tyres on the kerb when parking. Regularly check the wheels for damage. Seek the assistance of a workshop in the event of damage or unusual wear. The tools and the vehicle jacking equipment are in the load compartment. Winter tyres Winter tyres improve driving safety at temperatures below 7 °C and should therefore be fitted on all wheels. Tyres of size 185/65 R15, 195/65 R15 and 195/60 R16 C are permitted as winter tyres. In accordance with country-specific regulations, affix the speed sticker in the driver's field of view. 135 Tyre designations E.g. 215/60 R 16 95 H 215 = Tyre width, mm 60 = Cross-section ratio (tyre height to tyre width), % R = Belt type: Radial RF = Type: RunFlat C = Cargo or commercial use 16 = Wheel diameter, inches 95 = Load index e.g. 95 is equivalent to 690 kg H = Speed code letter Speed code letter: Q = up to 160 km/h S = up to 180 km/h T = up to 190 km/h H = up to 210 km/h V = up to 240 km/h W = up to 270 km/h Tyre pressure Check the pressure of cold tyres at least every 14 days and before any long journey. Do not forget the spare wheel. This also applies to vehicles with tyre pressure monitoring system. 136 Vehicle care Unscrew the valve cap. Tyre pressure 3 167 and on the label on the door frame. The tyre pressure data refers to cold tyres. It applies to summer and winter tyres. Always inflate the spare tyre to the pressure specified for full load. Incorrect tyre pressures will impair safety, vehicle handling, comfort and fuel economy and will increase tyre wear. For safety reasons, it is recommended that the tread depth of the tyres on one axle should not vary by more than 2 mm. Tread depth Check tread depth at regular intervals. Tyres should be replaced for safety reasons at a tread depth of 2-3 mm (4 mm for winter tyres). Changing tyre and wheel size If tyres of a different size than those fitted at the factory are used, it may be necessary to reprogramme the speedometer as well as the nominal tyre pressure and make other vehicle modifications. After converting to a different tyre size, have the label with tyre pressures replaced. 9 Warning If the pressure is too low, this can result in considerable tyre warmup and internal damage, leading to tread separation and even to tyre blow-out at high speeds. Tyres age, even if they are not used. We recommend tyre replacement every 6 years. The legally permissible minimum tread depth (1.6 mm) has been reached when the tread has worn down as far as one of the tread wear indicators (TWI). Their position is indicated by markings on the sidewall. If there is more wear at the front than the rear, swap round front wheels and rear wheels periodically. Ensure that the direction of rotation of the wheels is the same as before. 9 Warning Use of unsuitable tyres or wheels may lead to accidents and will invalidate the vehicle type approval. Vehicle care Wheel covers Tyre chains Tyre repair kit Minor damage to the tyre tread can be repaired with the tyre repair kit. Do not remove foreign bodies from the tyres. Tyre damage exceeding 4 mm or that is at tyre's sidewall cannot be repaired with the tyre repair kit. Wheel covers and tyres that are factory approved for the respective vehicle and comply with all of the relevant wheel and tyre combination requirements must be used. If the wheel covers and tyres used are not factory approved, the tyres must not have a rim protection ridge. Wheel covers must not impair brake cooling. 9 Warning 9 Warning Use of unsuitable tyres or wheel covers could lead to sudden pressure loss and thereby accidents. 137 Tyre chains are only permitted on the front wheels. Always use fine mesh chains that add no more than 10 mm to the tyre tread and the inboard sides (including chain lock). Do not exceed 50 km/h when tyre chains are fitted. 9 Warning Damage may lead to tyre blowout. Do not drive faster than 80 km/h. Do not use for a lengthy period. Steering and handling may be affected. If you have a flat tyre: Apply the parking brake and engage first or reverse gear. Van The tyre repair kit is located under the front seat or in the glovebox. Combi 138 Vehicle care The tyre repair kit is on the right side in the load compartment behind a cover. 1. Take the tyre repair kit from the vehicle. 2. Remove the compressor. 3. Set the compressor upright near the tyre. 4. Unscrew valve cap from defective tyre. 5. Screw the flexible filler hose onto the tyre valve. 6. The switch on the compressor must be set to J. 7. Connect the compressor plug to the power outlet or cigarette lighter socket. To avoid discharging the battery, we recommend running the engine. 8. Set the rocker switch on the compressor to I. The tyre is filled with sealant. 9. All of the sealant is pumped into the tyre. Then the tyre is inflated. Tyre pressure 3 167. When the correct pressure is obtained, switch off the compressor. 10. If a pressure of 1.5 bar is not obtained within 5 minutes, remove the tyre repair kit. Move the vehicle one tyre rotation. Reattach the tyre repair kit and continue the filling procedure for 5 minutes. If a pressure of 1.8 bar is still not obtained within Vehicle care 11. 12. 13. 14. 5 minutes, the tyre is too badly damaged. Seek the assistance of a workshop. Do not run the compressor longer than 20 minutes. Detach the tyre repair kit. Remove any excess sealant using a cloth. Take the label indicating maximum permitted speed from the sealant bottle and affix in the driver's field of view. Continue driving immediately so that sealant is evenly distributed in the tyre. After driving approx. 10 km (but no more than 10 minutes), stop and check tyre pressure. Screw compressor air hose directly onto tyre valve and compressor when doing this. If tyre pressure is more than 1.8 bar, set it to the correct value. Repeat the procedure until there is no more loss of pressure. If the tyre pressure has fallen below 1.8 bar, the vehicle must not be used. Seek the assistance of a workshop. 15. Stow away tyre repair kit in load compartment. Note The driving characteristics of the repaired tyre are severely affected, therefore have this tyre replaced. 139 If unusual noise is heard or the compressor becomes hot, turn compressor off and allow to cool. Note the expiry date of the kit. After this date its sealing capability is no longer guaranteed. Pay attention to storage information on sealant bottle. Replace the used sealant bottle. Dispose of the bottle as prescribed by applicable laws. The compressor and sealant can be used from approx. -20 °C. Replacing the sealant canister To replace the sealant canister: 1. Disconnect the compressor air hose. 140 Vehicle care 2. Turn the canister anticlockwise to lift it out. 3. Insert the new canister and turn it clockwise. 4. Connect the compressor air hose to the canister and fit the flexible filler tube into its allocated space. Wheel changing Some vehicles are equipped with a tyre repair kit instead of a spare wheel 3 137. Make the following preparations and observe the following information: ■ Park the vehicle on a level, firm and non-skid surface. The front wheels must be in the straight-ahead position. ■ Apply the parking brake and engage first or reverse gear. ■ Remove the spare wheel 3 142. ■ Never change more than one wheel at once. ■ Use the jack only to change wheels in case of puncture, not for seasonal winter or summer tyre change. ■ If the ground on which the vehicle is standing is soft, a solid board (max. 1 cm thick) should be placed under the jack. ■ No people or animals may be in the vehicle when it is jacked-up. ■ Never crawl under a jacked-up vehicle. ■ Do not start the vehicle when it is raised on the jack. ■ Clean wheel nuts and thread with a clean cloth before mounting the wheel. 9 Warning Do not grease wheel bolt, wheel nut and wheel nut cone. 1. Disengage wheel nut caps with a screwdriver and remove. Pull off the wheel cover using a suitable tool. Vehicle care 2. Attach wheel wrench securely and loosen each wheel nut by half a turn. 3. Vehicle jacking points are located at the front and rear. 4. Set the jack to the necessary height. Position it directly below the jacking point in a manner that prevents it from slipping. 141 With the jack correctly aligned, rotate until wheel is clear of the ground. 5. Unscrew the wheel nuts. 6. Change the wheel. Spare wheel 3 142. 7. Screw on the wheel nuts. 8. Lower vehicle. 9. Install the wheel wrench ensuring that it locates securely and tighten each nut in a crosswise sequence. Tightening torque is 85 Nm (steel wheel) or 120 Nm (alloy wheel). 10. Align the valve hole in the wheel cover with the tyre valve before installing. Install wheel nut caps. 11. Stow the replaced wheel 3 142 and the vehicle tools 3 134. 12. Check the tyre pressure of the installed tyre and the wheel nut torque as soon as possible. Have the defective tyre renewed or repaired as soon as possible. 142 Vehicle care Spare wheel Some vehicles are equipped with a tyre repair kit 3 137 instead of a spare wheel. The spare wheel can be classified as a temporary spare wheel depending on the size compared to the other mounted wheels and country regulations. Caution The use of a spare wheel that is smaller than the other wheels or in combination with winter tyres could affect driveability. Have the defective tyre replaced as soon as possible. Depending on model variant, the spare wheel is stored beneath the floor or in the load compartment. 1. Attach the extension bar 2 to the wheel wrench 1. Vehicle tools 3 134. 2. Insert the wheel wrench into the aperture in the load compartment floor. 3. Rotate the wheel wrench to lower the spare wheel to the floor. Vehicle care 5. Unscrew knob 2 and release cable attachment 1 from spare wheel. 6. Change the wheel. 7. Position the replaced wheel at the rear of the vehicle with the outside of the wheel facing downwards. 143 Have the defective tyre renewed or repaired as soon as possible. CNG vehicles Vehicles with CNG; the spare wheel is located in the load compartment. 4. Withdraw spare wheel from beneath the vehicle. 8. Pass the retainer 1 through the hole in the rim, inserting the locating pin into one of the bolt holes and secure with knob 2. 9. Insert the wheel wrench into the aperture in the load compartment floor and rotate to fully raise the spare wheel. 1. Unscrew two bolts using the wheel wrench and remove spare wheel from bracket. Vehicle tools 3 134. 144 Vehicle care 2. Change the wheel. 3. Position the replaced spare wheel onto the bracket ensuring correct alignment of the locating pin. 4. Secure spare wheel by tightening two bolts using the wheel wrench. Have the defective tyre renewed or repaired as soon as possible. Directional tyres Fit directional tyres such that they roll in the direction of travel. The rolling direction is indicated by a symbol (e.g. an arrow) on the sidewall. The following applies to tyres fitted opposing the rolling direction: ■ Driveability may be affected. Have the defective tyre renewed or repaired as soon as possible. ■ Drive particularly carefully on wet and snow-covered road surfaces. Jump starting Do not start with quick charger. A vehicle with a discharged battery can be started using jump leads and the battery of another vehicle. 9 Warning Be extremely careful when starting with jump leads. Any deviation from the following instructions can lead to injuries or damage caused by battery explosion or damage to the electrical systems of both vehicles. 9 Warning Avoid contact of the battery with eyes, skin, fabrics and painted surfaces. The fluid contains sulphuric acid which can cause injuries and damage in the event of direct contact. ■ Never expose the battery to naked flames or sparks. Vehicle care ■ A discharged battery can already freeze at a temperature of 0 °C. Defrost the frozen battery before connecting jump leads. ■ Wear eye protection and protective clothing when handling a battery. ■ Use a booster battery with the same voltage (12 Volts). Its capacity (Ah) must not be much less than that of the discharged battery. ■ Use jump leads with insulated terminals and a cross section of at least 16 mm2 (25 mm2 for diesel engines). ■ Do not disconnect the discharged battery from the vehicle. ■ Switch off all unnecessary electrical consumers. ■ Do not lean over the battery during jump starting. ■ Do not allow the terminals of one lead to touch those of the other lead. ■ The vehicles must not come into contact with each other during the jump starting process. ■ Apply the parking brake, transmission in neutral. Lead connection order: 1. Connect the red lead to the positive terminal of the booster battery. 2. Connect the other end of the red lead to the positive terminal of the discharged battery. 145 3. Connect the black lead to the negative terminal of the booster battery. 4. Connect the other end of the black lead to a vehicle grounding point, such as the engine block or an engine mounting bolt. Connect as far away from the discharged battery as possible, however at least 60 cm. Route the leads so that they cannot catch on rotating parts in the engine compartment. To start the engine: 1. Start the engine of the vehicle providing the jump. 2. After 5 minutes, start the other engine. Start attempts should be made for no longer than 15 seconds at an interval of 1 minute. 3. Allow both engines to idle for approx. 3 minutes with the leads connected. 146 Vehicle care 4. Switch on electrical consumers (e.g. headlights, heated rear window) of the vehicle receiving the jump start. 5. Reverse above sequence exactly when removing leads. Towing Towing the vehicle Caution The towing eye must only be used for towing and not for recovering the vehicle. Switch on ignition to release steering wheel lock and to permit operation of brake lights, horn and windscreen wiper. Transmission in neutral. Release the cap by carefully lifting with a screwdriver. To prevent damage, it is recommended to place a cloth between the screwdriver and the frame. The towing eye is stowed with the vehicle tools 3 134. Screw in the towing eye as far as it will go until it stops in a horizontal position. Attach a tow rope – or better still a tow rod – to the towing eye. Note If neutral cannot be selected on vehicles with manual transmission automated (MTA), the vehicle must only be towed with the drive wheels raised off the ground. Caution Drive slowly. Do not drive jerkily. Excessive tractive force can damage the vehicle. When the engine is not running, considerably more force is needed to brake and steer. Vehicle care To prevent the entry of exhaust gases from the towing vehicle, switch on the air recirculation and close the windows. Seek the assistance of a workshop. After towing, unscrew the towing eye and replace the cap. Towing another vehicle The towing eye is stowed with the vehicle tools 3 134. Screw in the towing eye as far as it will go until it stops in a horizontal position. Attach a tow rope – or even better a tow bar – to the towing eye. The towing eye must only be used for towing and not for recovering a vehicle. Caution Drive slowly. Do not drive jerkily. Excessive tractive force can damage the vehicle. After towing, unscrew the towing eye. Insert cap. Insert a screwdriver in the slot at the side of the cap. Release the cap by carefully levering the screwdriver. To prevent damage it is recommended to place a cloth between the screwdriver and the frame. 147 Appearance care Exterior care Locks The locks are lubricated at the factory using a high quality lock cylinder grease. Use de-icing agent only when absolutely necessary, as this has a degreasing effect and impairs lock function. After using de-icing agent, have the locks regreased by a workshop. Washing The paintwork of your vehicle is exposed to environmental influences. Wash and wax your vehicle regularly. When using automatic vehicle washes, select a programme that includes waxing. Bird droppings, dead insects, resin, pollen and the like should be cleaned off immediately, as they contain aggressive constituents which can cause paint damage. 148 Vehicle care If using a vehicle wash, comply with the vehicle wash manufacturer's instructions. The windscreen wiper and rear window wiper must be switched off. Remove antenna and external accessories such as roof racks etc. If you wash your vehicle by hand, make sure that the insides of the wheel housings are also thoroughly rinsed out. Clean edges and folds on opened doors and the bonnet as well as the areas they cover. Caution Always use a cleaning agent with a pH value of 4 to 9. Do not use cleaning agents on hot surfaces. Have the door hinges of all doors greased by a workshop. Do not clean the engine compartment with a steam-jet or high-pressure jet cleaner. Thoroughly rinse and leather-off the vehicle. Rinse leather frequently. Use separate leathers for painted and glass surfaces: remnants of wax on the windows will impair vision. Do not use hard objects to remove spots of tar. Use tar removal spray on painted surfaces. Exterior lights Headlight and other light covers are made of plastic. Do not use any abrasive or caustic agents, do not use an ice scraper, and do not clean them dry. Polishing and waxing Wax the vehicle regularly (at the latest when water no longer beads). Otherwise, the paintwork will dry out. Polishing is necessary only if the paint has become dull or if solid deposits have become attached to it. Paintwork polish with silicone forms a protective film, making waxing unnecessary. Plastic body parts must not be treated with wax or polishing agents. Windows and windscreen wiper blades Use a soft lint-free cloth or chamois leather together with window cleaner and insect remover. When cleaning the rear window, make sure the heating element inside is not damaged. For mechanical removal of ice, use a sharp-edged ice scraper. Press the scraper firmly against the glass so that no dirt can get under it and scratch the glass. Clean smearing wiper blades with a soft cloth and window cleaner. Glass panel Never clean with solvents or abrasive agents, fuels, aggressive media (e.g. paint cleaner, acetone-containing solutions etc.), acidic or highly alkaline media or abrasive pads. Do not apply wax or polishing agents to the glass panel. Wheels and tyres Do not use high-pressure jet cleaners. Vehicle care Clean rims with a pH-neutral wheel cleaner. Rims are painted and can be treated with the same agents as the body. Paintwork damage Rectify minor paintwork damage with a touch-up pen before rust forms. Have more extensive damage or rust areas repaired by a workshop. Underbody Some areas of the vehicle underbody have a PVC undercoating while other critical areas have a durable protective wax coating. After the underbody is washed, check the underbody and have it waxed if necessary. Bitumen/rubber materials could damage the PVC coating. Have underbody work carried out by a workshop. Before and after winter, wash the underbody and have the protective wax coating checked. Natural gas system Do not direct the steam jet or highpressure jet towards natural gas system components. It is particularly important to protect the natural gas tank and the pressure valves on the vehicle underbody and the bulkhead in the engine compartment. These components must not be treated using chemical cleaners or preservatives. Have components of the natural gas system cleaned by a workshop authorised to carry out maintenance of natural gas vehicles. Towing equipment Do not clean the coupling ball bar with a steam-jet or high-pressure jet cleaner. Interior care Interior and upholstery Only clean the vehicle interior, including the instrument panel fascia and panelling, with a dry cloth or interior cleaner. 149 Clean the leather upholstery with clear water and a soft cloth. In case of heavy soiling, use leather care. The instrument panel should only be cleaned using a soft damp cloth. Clean fabric upholstery with a vacuum cleaner and brush. Remove stains with an upholstery cleaner. Clothing fabrics may not be colourfast. This could cause visible discolourations, especially on lightcoloured upholstery. Removable stains and discolourations should be cleaned as soon as possible. Clean seat belts with lukewarm water or interior cleaner. Caution Close Velcro fasteners as open Velcro fasteners on clothing could damage seat upholstery. The same applies to clothing with sharp-edged objects, like zips or belts or studded jeans. 150 Vehicle care Plastic and rubber parts Plastic and rubber parts can be cleaned with the same cleaner as used to clean the body. Use interior cleaner if necessary. Do not use any other agent. Avoid solvents and petrol in particular. Do not use highpressure jet cleaners. Service and maintenance Service and maintenance General information ................... 151 Recommended fluids, lubricants and parts .................................... 152 General information Service information In order to ensure economical and safe vehicle operation and to maintain the value of your vehicle, it is of vital importance that all maintenance work is carried out at the proper intervals as specified. The detailed, up-to-date service schedule for your vehicle is available at the workshop. Service display 3 65. Service intervals - petrol and CNG engines Maintenance of your vehicle is required every 30,000 km or one year, whichever occurs first. Service intervals - diesel engines Maintenance of your vehicle is required every 35,000 km, or one year, whichever occurs first, unless otherwise indicated in the Driver Information Centre. 151 Confirmations Confirmation of service is recorded in the Service and Warranty Booklet. The date and mileage is completed with the stamp and signature of the servicing workshop. Make sure that the Service and Warranty Booklet is completed correctly as continuous proof of service is essential if any warranty or goodwill claims are to be met, and is also a benefit when selling the vehicle. Service interval with remaining engine oil life duration The service interval is based on several parameters depending on usage. When the engine oil requires changing, control indicator I will flash in conjunction with a message in the Driver Information Centre (DIC) 3 72. Service display 3 65. 152 Service and maintenance Recommended fluids, lubricants and parts Recommended fluids and lubricants Only use products that meet the recommended specifications. Damage resulting from the use of products not in line with these specifications will not be covered by the warranty. 9 Warning Operating materials are hazardous and could be poisonous. Handle with care. Pay attention to information given on the containers. Engine oil Engine oil is identified by its quality and its viscosity. Quality is more important than viscosity when selecting which engine oil to use. The oil quality ensures e.g. engine cleanliness, wear protection and oil ageing control, whereas viscosity grade gives information on the oil's thickness over a temperature range. Dexos is the newest engine oil quality that provides optimum protection for petrol and diesel engines. If it is unavailable, engine oils of other listed qualities must be used. Recommendations for petrol engines are also valid for Compressed Natural Gas (CNG) fuelled engines. Select the appropriate engine oil based on its quality and viscosity 3 155. Topping up engine oil Engine oils of different manufacturers and brands can be mixed as long as they comply with the required engine oil quality and viscosity. Use of engine oil with only ACEA A1/B1 or only A5/B5 quality is prohibited, since it can cause longterm engine damage under certain operating conditions. Select the appropriate engine oil based on its quality and viscosity 3 155. Additional engine oil additives The use of additional engine oil additives could cause damage and invalidate the warranty. Engine oil viscosity The SAE viscosity grade gives information on the thickness of the oil. Multigrade oil is indicated by two figures, e.g. SAE 5W-30. The first figure, followed by a W, indicates the low temperature viscosity and the second figure the high temperature viscosity. Select the appropriate viscosity grade 3 155. All of the recommended viscosity grades are suitable for high ambient temperatures. Coolant and antifreeze Use only antifreeze approved for the vehicle. Consult a workshop. The system is factory filled with coolant designed for excellent corrosion protection and frost protection down to approx. -28 °C. In northern countries with very low Service and maintenance temperatures the factory filled coolant provides frost protection down to approx. -37°C. This concentration should be maintained all year round. The use of additional coolant additives that intend to give additional corrosion protection or seal against minor leaks can cause function problems. Liability for consequences resulting from the use of additional coolant additives will be rejected. Brake and clutch fluid Only use high-performance brake fluid approved for the vehicle. Consult a workshop. Over time, brake fluid absorbs moisture which will reduce braking effectiveness. The brake fluid should therefore be replaced at the specified interval. Brake fluid should be stored in a sealed container to avoid water absorption. Ensure brake fluid does not become contaminated. 153 154 Technical data Technical data Vehicle identification .................. 154 Vehicle data ............................... 155 Vehicle identification Vehicle Identification Number and in the floor on the front passenger side behind a cover. Identification plate The Vehicle Identification Number is visible through the windscreen The identification plate is in the engine compartment. Technical data 8 = Engine type 9-11 = Vehicle-specific or countryspecific data Information on identification label: 1 = Type approval number 2 = Vehicle Identification Number 3 = Vehicle type identification code 4 = Permissible gross vehicle weight rating in kg 5 = Permissible gross train weight in kg 6 = Maximum permissible front axle load in kg 7 = Maximum permissible rear axle load in kg The combined total of front and rear axle loads must not exceed the permissible gross vehicle weight. For example, if the front axle is bearing its maximum permissible load, the rear axle can only bear a load that is equal to the gross vehicle weight minus the front axle load. The technical data is determined in accordance with European Community standards. We reserve the right to make modifications. Specifications in the vehicle documents always have priority over those given in this manual. 155 Vehicle data Recommended fluids and lubricants Required engine oil quality Petrol / Engine oil CNG quality engines Diesel engines dexos 2 ✔ ✔ In case dexos quality is unavailable in International countries you may use the oil qualities listed below: Petrol / Engine oil CNG quality engines Diesel engines GM-LLA-025 ✔ - GM-LLB-025 - ✔ 156 Technical data Engine oil viscosity grades Engine oil viscosity grade Petrol / CNG engines Diesel engines SAE 0W-30 - ✔ SAE 0W-40 ✔ - Technical data Engine data Sales designation 1.4 1.4 1.4 Engine identifier code 1.4i 1.4Turbo 1.4CNG Number of cylinders 4 4 4 Piston displacement [cm3] 1368 1368 1368 Engine power [kW] 70 88 88 at rpm 6000 5000 5000 Torque [Nm] 127 206 206 at rpm 4500 3000 3000 Fuel type Petrol Petrol Compressed Natural Gas/Petrol recommended 95 95 95 possible 98 98 98 possible 91 91 91 Gas – – CNG Oil consumption [l/1000 km] 0.6 0.6 0.6 Octane rating RON 157 158 Technical data Sales designation 1.3 Turbo 1.6 Turbo 2.0 Turbo Engine identifier code 1.3CDTI 1.6CDTI1) 2.0CDTI Number of cylinders 4 4 4 1248 1598 1956 Engine power [kW] 66 66 / 77 99 at rpm 4000 4000 3500 Torque [Nm] 200 2002) / 290 320 at rpm 1500 1500 1500 Fuel type Diesel Diesel Diesel Oil consumption [l/1000 km] 0.6 0.6 0.6 Piston displacement 1) 2) [cm3] Low / High output. Vehicles with manual transmission automated (MTA). Technical data 159 Performance The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload. Optional equipment could reduce the specified maximum speed of the vehicle. Engine 1.4i 1.4Turbo 1.4CNG Manual transmission 161 172 172 Manual transmission automated – – – Maximum speed [km/h] Engine 1.3CDTI 1.6CDTI3) 2.0CDTI 158 / 1535) 164 / 1584) / 1535) Maximum speed [km/h] Manual transmission Manual transmission automated 3) 5) 4) Low / High output. High roof version. Low roof version. –/– –/ 1584) / 1535) 179 – 160 Technical data Vehicle weight Kerb weight, basic model - Van Length Roof height Engine Gross vehicle weight Kerb weight L1 H1 1.4i 1990 / 2160 1240 / 1260 1.4Turbo – / 2325 – / 1400 1.4Turbo CNG 2430 / – 1450 / – 1.3CDTI 2020 / 2290 1270 / 1290 1.6CDTI 2060 / 2330 1310 / 1330 2.0CDTI 2100 / 2370 1350 / 1370 1.4i 2010 / 2180 1260 / 1280 1.4Turbo – / 2345 – / 1420 1.4Turbo CNG 2420 / – 1470 / – 1.6CDTI 2080 / 2350 1330 / 1350 2.0CDTI 2120 / 2390 1370 / 1390 H2 Technical data Length Roof height Engine Gross vehicle weight Kerb weight L2 H1 1.4i 2200 / – 1300 / – 1.4Turbo 2365 / – 1440 / – 1.4Turbo CNG 2470 / 2450 1490 / 1540 1.3CDTI 2330 / – 1330 / – 1.6CDTI 2370 / – 1370 / – 2.0CDTI 2410 / – 1410 / – 1.4Turbo 2455 1455 1.6CDTI 2460 1460 2.0CDTI 2500 1500 H2 161 162 Technical data Kerb weight, basic model - Combi Length Roof height Engine Gross vehicle weight Kerb weight L1 H1 1.4i 2060 1350 1.4Turbo 2225 1500 1.3CDTI 2090 1380 1.6CDTI 2130 1420 2.0CDTI 2170 1460 1.4i 2160 1360 1.3CDTI 2190 1390 1.6CDTI 2230 1430 2.0CDTI 2270 1470 1.4i 2200 1400 1.4Turbo 2265 1540 1.3CDTI 2230 1430 1.6CDTI 2270 1470 2.0CDTI 2310 1510 2.0CDTI 2400 1600 H2 L2 H1 H2 Technical data Kerb weight, basic model - Combo Tour Length Roof height Engine Gross vehicle weight Kerb weight L1 H1 1.4i 1940 1340 1.4Turbo 2030 1490 1.4Turbo CNG 2110 1540 1.3CDTI 1970 1370 1.6CDTI 2010 1410 2.0CDTI 2050 1450 1.4i 2210 1430 1.6CDTI 2400 1500 2.0CDTI 2440 1540 1.4i 2055 1370 1.4Turbo 2135 1490 1.3CDTI 2085 1400 1.6CDTI 2115 1430 2.0CDTI 2165 1480 2.0CDTI 2215 1600 H2 L2 H1 H2 163 164 Technical data Vehicle dimensions Type Van Wheelbase Short Long Short Long Short Long Length [mm] 4390 4740 4390 4740 4390 4740 Width without exterior mirrors [mm] 1832 1832 1832 1832 1832 1832 Width with exterior mirrors [mm] Combi 2119 2119 Combo Tour 2119 2119 2119 2119 Height (without antenna) [mm] Standard roof 1845 / High roof 2100 2125 2100 – 2100 – Length of load compartment floor 1820 [mm] 2170 – – – – Load compartment width [mm] 1230 1230 1230 1230 1195 1195 Load compartment height [mm] Standard roof 1305 1305 1305 1305 1305 1305 High roof 1550 – 1550 – 1550 – 6) 7) Versions with roof rack. Versions with roof bars. 18956) 1880 / 19277) 1845 / 18956) 1880 / 19276) 1845 / 18956) 1880 / 19276) Technical data Type Van Combi Combo Tour Wheelbase [mm] 2755 3105 2755 3105 2755 3105 Turning circle kerb to kerb [m] 11.2 12.5 11.2 12.5 11.2 12.5 165 166 Technical data Capacities Engine oil Engine 1.4i 1.4Turbo 1.4CNG 1.3CDTI 1.6CDTI 2.0CDTI including Filter [l] 2.7 2.9 2.7 3.2 4.9 4.9 between MIN and MAX [l] 1.0 1.0 1.0 1.0 1.0 1.0 Fuel tank Petrol/diesel, nominal capacity [l] 60 Natural gas CNG, nominal capacity [kg] Petrol, nominal capacity [l] 16.15 kg8) / 22.1 kg9) 22 8) 9) Short wheelbase version. Long wheelbase version. Technical data 167 Tyre pressures Van Comfort with up to 2 people and 100 kg luggage With full load front rear front [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) 185/65 R15 88T 250/2.5 (36) 250/2.5 (36) 290/2.9 (42) 290/2.9 (42) 185/65 R15 92T 250/2.5 (36) 260/2.6 (38) 290/2.9 (42) 300/3.0 (44) 195/65 R15 95T 240/2.4 (35) 240/2.4 (35) 260/2.6 (38) 270/2.7 (39) 195/60 R16 C 99/97T 270/2.7 (39) 270/2.7 (39) 270/2.7 (39) 330/3.3 (48) 360/3.6 (52)10)11) Engine Tyres All Adjust tyre pressure to the value specified for full load when driving at speeds of 160 km/h. 10) 11) Long wheelbase version. CNG version. rear 168 Technical data Combi Engine All Comfort with up to 3 people With full load front rear front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) 185/65 R15 88T 250/2.5 (36) 250/2.5 (36) 290/2.9 (42) 290/2.9 (42) 185/65 R15 92T 250/2.5 (36) 260/2.6 (38) 290/2.9 (42) 300/3.0 (44) 195/65 R15 95T 240/2.4 (35) 300/3.0 (44) 260/2.6 (38) 320/3.2 (46) 195/60 R16 C 99/97T 270/2.7 (39) 270/2.7 (39) 270/2.7 (39) 360/3.6 (52) Tyres Adjust tyre pressure to the value specified for full load when driving at speeds of 160 km/h. Technical data Combo Tour Engine All Comfort with up to 3 people With full load front rear front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) 185/65 R15 88T 250/2.5 (36) 250/2.5 (36) 290/2.9 (42) 290/2.9 (42) 185/65 R15 92T 250/2.5 (36) 260/2.6 (38) 290/2.9 (42) 300/3.0 (44) 195/65 R15 95T 240/2.4 (35) 240/2.4 (35) 260/2.6 (38) 260/2.6 (38) 195/60 R16 C 99/97T 270/2.7 (39) 270/2.7 (39) 270/2.7 (39) 280/2.8 (41) 12) 360/3.6 (52) 13)11) Tyres Adjust tyre pressure to the value specified for full load when driving at speeds of 160 km/h. 12) 13) 11) Version with 5 seats. Version with 7 seats. CNG version. 169 170 Customer information Customer information Vehicle data recording and privacy ....................................... 170 Vehicle data recording and privacy Event data recorders Data storage modules in the vehicle A large number of electronic components of your vehicle contain data storage modules temporarily or permanently storing technical data about the condition of the vehicle, events and errors. In general, this technical information documents the condition of parts, modules, systems or the environment: ■ Operating conditions of system components (e.g. filling levels) ■ Status messages of the vehicle and its single components (e.g. number of wheel revolutions / rotational speed, deceleration, lateral acceleration) ■ Dysfunctions and defects in important system components ■ Vehicle reactions in particular driving situations (e.g. inflation of an airbag, activation of the stability regulation system) ■ Environmental conditions (e.g. temperature) This data is exclusively technical and helps identifying and correcting errors as well as optimizing vehicle functions. Motion profiles indicating travelled routes cannot be created with this data. If services are used (e.g. repair works, service processes, warranty cases, quality assurance), employees of the service network (manufacturer included) are able to read out this technical information from the event and error data storage modules applying special diagnostic devices. If required, you will receive further information at these workshops. After an error has been corrected, the data is deleted from the error storage module or it is constantly overwritten. Customer information When using the vehicle, situations may occur in which technical data related to other information (accident report, damages on the vehicle, witness statements etc.) may be associated with a specific person possibly, with the assistance of an expert. Additional functions contractually agreed upon with the client (e.g. vehicle location in emergency cases) allow the transmission of particular vehicle data from the vehicle. Radio Frequency Identification (RFID) RFID technology is used in some vehicles for functions such as tyre pressure monitoring and ignition system security. It is also used in connection with conveniences such as radio remote controls for door locking/unlocking and starting, and invehicle transmitters for garage door openers. RFID technology in Opel vehicles does not use or record personal information or link with any other Opel system containing personal information. 171 172 Index A Accessories and vehicle modifications .......................... 118 Adjustable air vents ..................... 92 Airbag activation........................... 74 Airbag and belt tensioners ........... 68 Airbag deactivation .......... 42, 69, 74 Airbag system .............................. 40 Air conditioning regular operation 94 Air conditioning system ................ 90 Air intake ...................................... 93 Air vents........................................ 92 Alert.............................................. 80 Antilock brake system ................ 105 Antilock brake system (ABS) ....... 70 Anti slip-regulator........................ 107 Anti-theft locking system .............. 25 Appearance care........................ 147 Armrest......................................... 35 Ashtrays ....................................... 62 Audible warning chimes................ 80 Autoclose...................................... 74 Automatic fuel cut-off.............. 80, 96 Automatic locking......................... 74 B Battery ....................................... 123 Bonnet ....................................... 120 Brake and clutch fluid................. 152 Brake assist ............................... 106 Brake fluid .................................. 123 Brake pad wear............................ 70 Brakes ............................... 105, 123 Brake system ............................... 70 Breakdown.................................. 146 Bulb replacement ....................... 125 C Capacities .................................. 166 Car Pass ...................................... 19 Catalytic converter ..................... 100 Central locking system ................ 20 Centre high-mounted brake light ......................................... 128 Change engine oil ....................... 72 Changing tyre and wheel size . . . 136 Charging system .......................... 69 Child locks ................................... 22 Child restraint installation locations ................................... 45 Child restraint systems ................ 44 Child safety system for rear windows.................................... 28 Chimes......................................... 80 Cigarette lighter ........................... 62 Climate control ............................. 16 Climate control systems............... 89 Clock....................................... 59, 74 Control indicators.......................... 66 173 Control of the vehicle ................... 95 Controls........................................ 57 Convex shape .............................. 26 Coolant and antifreeze............... 152 Cruise control ...................... 74, 108 Cupholders .................................. 50 D Danger, Warnings and Cautions . . . 3 Date.............................................. 74 Daytime running lights............ 74, 84 Diesel particle filter................. 72, 99 Distance to next service............... 74 Door open .................................... 74 Doors................................ 22, 23, 24 Drain fuel filter ............................. 73 Driver Information Centre............. 74 Driving characteristics and towing tips .............................. 116 E Eco mode (E).............................. 104 Electric adjustment ...................... 27 Electrical system......................... 131 Electronic climate control system 91 Electronic driving programmes . . 104 Electronic stability program ....... 107 Electronic Stability Program fault.. 71 End-of-life vehicle recovery ....... 119 Engine compartment fuse box ... 132 Engine coolant ........................... 121 Engine coolant temperature ........ 71 Engine coolant temperature gauge ....................................... 65 Engine data ............................... 157 Engine exhaust ............................ 99 Engine oil ................... 120, 152, 155 Engine oil pressure ...................... 72 Event data recorders.................. 170 Extendable load compartment cover................................... 51, 55 Exterior care .............................. 147 Exterior light ................................. 74 Exterior lighting ...................... 13, 83 Exterior mirrors............................. 26 F Fault ........................................... 105 Fixed air vents ............................. 93 Fog light ....................................... 74 Folding ......................................... 27 Front airbag system ..................... 41 Front fog lights ............................. 85 Front seats.................................... 33 Front turn signal light.................. 125 Fuel............................................. 111 Fuel consumption......................... 74 Fuel consumption - CO2Emissions ............................... 115 Fuel cut-off system................. 80, 96 Fuel for diesel engines .............. 112 Fuel for natural gas operation . . . 112 Fuel for petrol engines ............... 111 Fuel gauge ................................... 64 Fuel selector ................................ 65 Fuel system messages................. 80 Fuses ......................................... 131 G Gauges......................................... 63 General information ................... 116 Generic warning........................... 68 Glovebox ..................................... 50 Gross Vehicle Weight................... 55 H Halogen headlights .................... 125 Hand brake................................. 106 Hazard warning flashers .............. 85 Headlight flash ............................. 83 Headlight range adjustment ........ 84 Headlights..................................... 83 Headlights when driving abroad . . 84 Head restraint adjustment ............. 8 Head restraints ............................ 32 Heated ......................................... 27 Heated rear window ..................... 30 Heating ........................................ 35 Heating and ventilation system . . . 89 High beam ............................. 74, 83 174 Hill start assist...................... 70, 106 Horn ....................................... 14, 58 I Identification plate ..................... 154 Ignition switch positions ............... 96 Immobiliser ............................ 26, 73 Indicators...................................... 63 Information displays...................... 74 Instrument panel fuse box ......... 133 Instrument panel illumination ..... 130 Instrument panel illumination control ...................................... 86 Instrument panel overview ........... 10 Instrument panel storage.............. 49 Interior care ............................... 149 Interior lighting........................ 74, 86 Interior lights ........................ 87, 129 Interior mirrors.............................. 28 Introduction .................................... 3 ISOFIX child restraint systems .... 48 J Jump starting ............................. 144 K Kerb weight................................... 55 Keys ............................................. 19 Keys, locks................................... 19 L Language..................................... 74 Lashing eyes ......................... 54, 55 Light switch .................................. 83 Load compartment ................ 24, 51 Load compartment cover ............. 51 Load compartment lighting........... 88 Loading information ..................... 55 Low engine oil level ..................... 73 Low fuel ....................................... 73 O Object detection systems........... 109 Odometer ..................................... 63 Oil, engine.......................... 152, 155 Operating windows from outside. . 28 Outside temperature .................... 59 Overhead console ....................... 50 Overrun cut-off ............................. 97 P Malfunction indicator light ............ 69 Manual adjustment ...................... 26 Manual anti-dazzle ...................... 28 Manual mode ............................. 104 Manual transmission .................. 101 Manual transmission automated .............................. 101 Manual windows .......................... 28 Mirror adjustment ........................... 8 Misted light covers ....................... 86 Multifunction display..................... 74 Parking .................................. 18, 99 Parking assist ............................ 109 Parking brake ............................ 106 Particulate filter............................. 99 Payload......................................... 55 Performance .............................. 159 Performing work ........................ 119 Pollen filter ................................... 93 Power outlets ............................... 61 Power steering fluid.................... 122 Power windows ............................ 28 Preheating ................................... 72 Puncture..................................... 140 N R M New vehicle running-in ................ 95 Number plate light ..................... 128 Radio Frequency Identification (RFID)..................................... 171 Radio info..................................... 74 Radio remote control ................... 19 Rear doors ................................... 23 175 Rear fog light ............................... 74 Rear fog lights ............................. 86 Rear parcel shelf.......................... 51 Rear windows .............................. 30 Rear window wiper/washer .......... 59 Recommended fluids and lubricants ........................ 152, 155 Refuelling ................................... 113 Reversing lights ........................... 86 Ride control systems.................. 107 Roof load...................................... 55 Roof rack ..................................... 54 Roof racks.................................... 55 S Seat adjustment ....................... 7, 33 Seat belt ........................................ 8 Seat belt reminder ....................... 68 Seat belt reminder warning chime 74 Seat belts ..................................... 37 Seat position ................................ 33 Selector lever ............................. 102 Service ................................. 94, 151 Service display ...................... 65, 74 Service information .................... 151 Settings menu............................... 74 Side airbag system ...................... 42 Sidelights...................................... 83 Side turn signal lights ................ 128 Sliding door .................................. 22 Sliding side door........................... 22 Spare wheel ............................... 142 Speed limit warning chime............ 74 Speedometer ............................... 63 Standard display........................... 74 Starting off ................................... 17 Starting the engine .............. 96, 102 Steering wheel adjustment ...... 9, 57 Steering wheel controls ............... 57 Stop-start system.................... 73, 97 Storage......................................... 50 Storage compartments................. 50 Sun visors .................................... 30 Symbols ......................................... 4 T Tachometer ................................. 64 Tailgate......................................... 24 Tail lights ................................... 127 Temperature................................. 74 Third row seats ............................ 35 Three-point seat belt .................... 38 Tools .......................................... 134 Top-tether fastening eyes ............ 48 Towing................................ 116, 146 Towing another vehicle ............. 147 Towing the vehicle ..................... 146 Traction Control system ............. 107 Trailer coupling........................... 116 Trailer towing ............................. 116 Transmission ............................... 16 Transmission display ................. 101 Tread depth ............................... 136 Trip computer......................... 74, 81 Trip odometer .............................. 63 Turn and lane-change signals ..... 85 Turn signal ................................... 68 Tyre chains ................................ 137 Tyre designations ...................... 135 Tyre pressure ............................ 135 Tyre pressures ........................... 167 Tyre repair kit ............................. 137 U Ultrasonic parking assist ...... 71, 109 Underseat storage ....................... 50 Unit of measurement.................... 74 Upholstery.................................. 149 Upshift.......................................... 70 Using this manual .......................... 3 V Vehicle checks............................ 119 Vehicle data................................ 155 Vehicle data recording and privacy..................................... 170 Vehicle dimensions .................... 164 Vehicle Identification Number .... 154 Vehicle jack................................ 134 Vehicle security............................ 25 176 Vehicle shutdown................... 80, 96 Vehicle specific data ...................... 3 Vehicle storage........................... 118 Vehicle tools............................... 134 Vehicle unlocking ........................... 6 Vehicle weight ........................... 160 Ventilation..................................... 89 Volume......................................... 74 W Warning chime.............................. 74 Warning chimes ........................... 80 Warning lights............................... 63 Washer and wiper systems ......... 15 Washer fluid ............................... 122 Wheel changing ......................... 140 Wheel covers ............................. 137 Wheels and tyres ....................... 135 Windows....................................... 28 Windscreen................................... 28 Windscreen wiper/washer ........... 58 Winter tyres ............................... 135 Wiper blade replacement .......... 124 Copyright by ADAM OPEL AG, Rüsselsheim, Germany. The information contained in this publication is effective as of the date indicated below. Adam Opel AG reserves the right to make changes to the technical specifications, features and design of the vehicles relative to the information in this publication as well as changes to the publication itself. Edition: August 2012, ADAM OPEL AG, Rüsselsheim. Printed on chlorine-free bleached paper. KTA-2730/1-en *KTA-2730/1-EN* August 2012