सीईडी/CED कार्य र्ोजना (01 अप्रैल 2014 तक ) PROGRAMME OF WORK ( AS ON 01 April 2014 ) ससविल इंजीननर्र ग ं विभाग (सीईडी) Civil Engineering Department (CED) भारतीय मानक ब्यरू ो मानक भवन, 9 बहादरु शाह ज़फर मार्ग नई ददल्ली – 110 002 BUREAU OF INDIAN STANDARDS MANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG NEW DELHI 110002 1 PREFACE This Programme of Work, prepared every year for Civil Engineering Division Council (CEDC), indicates the latest position of published Indian Standards, their present status and draft standards at different stages under CEDC, as on 1 April 2014. The present scope of CEDC is as follows: ‘Standardization in field of Civil Engineering including structural engineering, building materials and components, planning, design, construction and maintenance of civil engineering structures and built environment, construction practices, safety in building; but excluding those subjects which specifically relate to Water Resources Development and Management’. The Division Council is working towards achieving the above goal through 35 Sectional Committees covering wide range of subjects for basic building materials, design and construction to very high technical areas like Offshore Installations, Ports and Harbours, Cyclone Resistant Structures, etc. Standards, drafts and special publications (Handbooks) are listed under respective Sectional Committees, a list of which is given in the Table of Contents’ to serve as a key for easy location. Under each committee the corresponding Technical Committee (TC) of the International Organization for Standardization (ISO), if any, is also listed with the status of membership. The letter `P’ after the TC number indicates that India is `Participating’ member and letter `O’ indicates `Observer’ member status. If you need further information, please write to: Scientist ‘F’ & Head (Civil Engg.) Bureau of Indian Standards Manak Bhavan 9 Bahadur Shah Zafar Marg NEW DELHI 110 002 Phone: 011 – 2323 5529 Fax: 011 – 2323 5529 e-mail: ced@bis.org.in Website: www.bis.org.in For periodic update of this Programme of Work, kindly refer our website, www.bis.org.in. For bilingual standards / standards in Hindi, kindly refer the BIS Catalogue. Disclaimer: CED is not responsible for any inadvertent error that may have crept in the information published in this publication. The information published herein is for immediate information only and no legal claim can be made for any damage caused by using the content of this publication. CED reserves the right to change the information published herein, or in its website at any point of time without further notification. For latest information of standards, kindly refer the ‘ONLINE CATALOGUE’ in our website. 2 CIVIL ENGINEERING DEPARTMENT Committee No. CED 2 CED 3 CED 4 CED 5 CED 6 CED 7 CED 9 CED 11 CED 12 CED 13 CED 15 CED 20 CED 22 CED 24 CED 29 CED 30 CED 35 CED 36 CED 37 CED 38 CED 39 CED 41 CED 43 CED 44 CED 46 CED 47 CED 48 CED 50 CED 51 CED 53 CED 54 CED 55 CED 56 CED 57 CED 58 ANNEX I ANNEX II ANNEX III ANNEX IV ANNEX V ANNEX VI ANNEX VII ANNEX VIII ANNEX IX Title of the Committee ASPECT WISE ANALYSIS CEMENT AND CONCERTE SECTIONAL COMMITTEE SANITARY APPLIANCES AND WATER FITTINGS SECTIONAL COMMITTEE BUILDING LIMES AND GYPSUM PRODUCTS SECTIONAL COMMITTEE FLOORING, WALL FINISHING AND ROOFING SECTIONAL COMMITTEE STONES SECTIONAL COMMITTEE STRUCTURAL ENGINEERING AND STRUCTURAL SECTIONS SECTIONAL COMMITTEE TIMBER AND TIMBER STORES SECTIONAL COMMITTEE DOORS, WINDOWS AND SHUTTER SECTIONAL COMMITTEE FUNCTIONAL REQUIREMENTS IN BUILDINGS SECTIONAL COMMITTEE BUILDING CONSTRUCTION PRACTICES SECTIONAL COMMITTEE BUILDERS' HARDWARE SECTIONAL COMMITTEE WOOD AND OTHER LIGNOCELLULOSIC PRODUCTS SECTIONAL COMMITTEE FIRE FIGHTING SECTIONAL COMMITTEE PUBLIC HEALTH ENGINEERING SECTIONAL COMMITTEE CONSTRUCTION MANAGEMENT (INCLUDING SAFETY IN CONSTRUCTION) SECTIONAL COMMITTEE CLAY AND STABILIZED PRODUCTS FOR CONSTRUCTION SECTIONAL COMMITTEE FURNITURE SECTIONAL COMMITTEE FIRE SAFETY SECTIONAL COMMITTEE STRUCTURAL SAFETY SECTIONAL COMMITTEE SPECIAL STRUCTURES SECTIONAL COMMITTEE EARTHQUAKE ENGINEERING SECTIONAL COMMITTEE WATER-PROOFING AND DAMP-PROOFING SECTIONAL COMMITTEE SOIL AND FOUNDATION ENGINEERING SECTIONAL COMMITTEE METHODS OF MEASUREMENT OF WORKS OF CIVIL ENGINEERING (EXCLUDING WATER RESOURCES DEVELOPMENT DIVISION) SECTIONAL COMMITTEE NATIONAL BUILDING CODE SECTIONAL COMMITTEE PORTS, HARBOURS AND OFFSHORE INSTALLATIONS SECTIONAL COMMITTEE ROCK MECHANICS SECTIONAL COMMITTEE PLASTIC PIPING SYSTEMS SECTIONAL COMMITTEE PLANNING, HOUSING AND PREFABRICATED CONSTRUCTION SECTIONAL COMMITTEE CEMENT MATRIX PRODUCTS SECTIONAL COMMITTEE CONCRETE REINFORCEMENT SECTIONAL COMMITTEE SIEVES, SIEVING AND OTHER SIZING METHODS SECTIONAL COMMITTEE HILL AREA DEVELOPMENT ENGINEERING SECTIONAL COMMITTEE CYCLONE RESISTANT STRUCTURES SECTIONAL COMMITTEE SUSTAINABILITY IN BUILDING CONSTRUCTION SECTIONAL COMMITTEE STANDARDS WITHDRAWN/SUPERSEDED LIST OF IS WITH DUAL NUMBER/EQUIVALENT STANDARDS/HARMONIZED WITH OTHER STANDARDS ORGANIZATION LIKE II A, II B, II C etc. LIST OF IS NO. COVERED UNDER BIS CERTIFICATION MARKS SCHEME INDIAN STANDARDS WITH ECO MARK PROVISIONS BILINGUAL STANDARDS MEMBERSHIP STATUS IN ISO TC/SCs LIST OF MANDATORY STANDARDS LIST OF IS TRANSFERRED TO OTHER DEPARTMENTS LIST OF SPECIAL PUBLICATIONS 3 ASPECTWISE BREAKUP OF STANDARDS (As on 1 Apr 2014) Committee No. Product Code of Practice Method of Test Dimensional Terminology Symbols Others Total CED 2 51 20 47 0 14 0 3 135 CED 3 69 1 1 0 0 0 1 72 CED 4 20 12 32 0 2 0 0 66 CED 5 27 21 21 0 2 0 3 74 CED 6 10 4 16 0 1 0 12 43 CED 7 20 19 0 13 0 0 9 61 CED 9 83 7 39 0 2 1 22 154 CED 11 21 2 16 0 1 1 0 41 CED 12 1 17 3 0 1 0 2 24 CED 13 10 68 6 1 3 0 7 96 CED 15 42 0 0 0 0 0 0 42 CED 20 46 6 52 0 0 0 2 106 CED 22 86 17 0 0 1 1 30 135 CED 24 26 25 1 0 1 0 8 61 CED 29 0 25 0 0 0 0 4 29 CED 30 20 1 1 1 1 0 4 28 CED 35 45 1 13 2 1 0 1 63 CED 36 3 27 4 0 1 2 1 38 CED 37 0 5 0 0 0 0 1 6 CED 38 0 9 0 0 0 0 1 10 CED 39 0 8 0 0 0 0 4 12 CED 41 8 11 11 0 1 0 0 31 CED 43 18 33 60 0 2 0 13 126 CED 44 0 0 0 0 0 0 29 29 CED 46 0 0 0 0 0 0 11 11 CED 47 0 9 0 0 1 0 1 11 CED 48 1 12 16 0 1 0 23 53 CED 50 56 4 23 0 0 0 2 84 CED 51 8 35 0 0 3 0 0 46 CED 53 42 8 21 0 1 0 18 90 CED 54 11 0 0 0 0 0 3 14 CED 55 7 1 6 0 2 2 0 18 CED 56 0 0 0 0 0 0 7 7 CED 57 0 0 0 0 0 0 2 2 CED 58 0 0 0 0 0 0 0 0 TOTAL 735 Specifn 408 386 17 42 7 224 1818 The aspect wise break-up is based on the main contents of the standards and users may refer to the standards for details. 4 CED 2 CEMENT AND CONCRETE SCOPE - STANDARDIZATION IN THE FIELD OF ALL TYPES OF CEMENT, POZZOLANA, TESTING SAND, CONCRETE, AGGREGATES, INSTRUMENTS FOR CEMENT AND CONCRETE TESTING, CEMENT PLANT MACHINERY AND FERROCEMENT LIAISON: ISO/TC 71 (P) CONCRETE, REINFORCED CONCRETE AND PRE-STRESSED CONCRETE ISO/TC 71/SC 1 (P) TEST METHODS FOR CONCRETE ISO/TC 71/SC 3 (P) CONCRETE PRODUCTION AND EXECUTION OF CONCRETE STRUCTURES ISO/TC 71/SC 4 (P) PERFORMANCE REQUIREMENTS FOR STRUCTURAL CONCRETE ISO/TC 71/SC 5 (O) SIMPLIFIED DESIGN STANDARD FOR CONCRETE STRUCTURES ISO/TC 71/SC 6 (P) NON-TRADITIONAL REINFORCING MATERIALS FOR CONCRETE STRUCTURES ISO/TC 71/SC 7 (O) MAINTENANCE AND REPAIR OF CONCRETE STRUCTURES ISO/TC 71/SC 8 (P) ENVIRONMENTAL MANAGEMENT FOR CONCRETE AND CONCRETE STRUCTURES ISO/TC 74 (P) CEMENT AND LIME Sl. No. IS Number/ DOC Number Title Reaffirm Date No. of Amd. STANDARDS PUBLISHED 1 IS 269:2013 Specification for ordinary Portland cement, 33 grade (fifth revision) 2 *IS 383:1970 Specification for coarse and fine aggregates from natural sources for concrete (second revision) Apr 2011 3 IS 455:1989 Specification for Portland slag cement (fourth revision) Jul 2009 6 4 IS 456:2000 Code of practice for plain and reinforced concrete (fourth revision) Feb 2011 4 5 IS 457:1957 Code of practice for general construction of plain and reinforced concrete for dams and other massive structures Jul 2009 6 IS 516:1959 Method of test for strength of concrete Oct 2013 2 7 IS 650:1991 Specification for standard sand for testing of cement (second revision) Oct 2013 1 8 IS 1199:1959 Methods of sampling and analysis of concrete Oct 2013 9 IS 1343:2012 Code of practice for prestressed concrete (second revision) 10 IS 1344:1981 Specification for calcined clay pozzolana (second revision) Oct 2013 1 11 IS 1489(Part 1):1991 Specification for Portland pozzolana cement: Part 1 Flyash based (third revision) Jul 2009 5 12 IS 1489(Part 2):1991 Specification for Portland-pozzolana cement: Part 2 Calcined clay based (third revision) Jul 2009 4 13 IS 1727:1967 Methods of test for pozzolanic materials (first revision) Oct 2013 2 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS 1 ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 5 Sl. No. IS Number/ DOC Number Title Reaffirm Date 14 IS 2386(Part 1):1963 Methods of test for aggregates for concrete: Part 1 Particle size and shape Apr 2011 4 15 IS 2386(Part 2):1963 Methods of test for aggregates for concrete: Part 2 Estimation of deleterious materials and organic Apr 2011 1 16 IS 2386(Part 3):1963 Methods of test for aggregates for concrete: Part 3 Specific gravity, density, voids, absorption and bulking Apr 2011 17 IS 2386(Part 4):1963 Methods of test for aggregates for concrete: Part 4 Mechanical properties Apr 2011 18 IS 2386(Part 5):1963 Methods of test for aggregates for concrete : Part 5 Soundness Apr 2011 19 IS 2386(Part 6):1963 Methods of test for aggregates for concrete : Part 6 Measuring mortar making properties of fine aggregates Apr 2011 2 20 IS 2386(Part 7):1963 Methods of test for aggregates for concrete : Part 7 Alkali aggregate reactivity Apr 2011 2 21 IS 2386(Part 8):1963 Methods of test for aggregates for concrete: Part 8 Petrographic examination Apr 2011 1 22 IS 2430:1986 Methods for sampling of aggregates for concrete (first revision) Jul 2009 23 IS 2502:1963 Code of practice for bending and fixing of bars for concrete reinforcement Oct 2013 24 IS 2645:2003 Specification for integral waterproofing compounds for cement mortar and concrete - (second revision) Apr 2012 25 IS 2770(Part 1):1967 Methods of testing bond in reinforced concrete: Part 1 Pull-out test Feb 2012 26 IS 3085:1965 Method of test for permeability of cement mortar and concrete Apr 2011 27 IS 3370(Part 1):2009 Code of practice for concrete structures for storage of liquids: Part 1 General requirements (first revision) 28 IS 3370(Part 2):2009 Code of practice for concrete structures for storage of liquids: Part 2 Reinforced concrete structures (first revision) 29 IS 3370(Part 3):1967 Code of practice for concrete structures for the storage of liquids: Part 3 Prestressed concrete structures Oct 2013 1 30 IS 3370(Part 4):1967 Code of practice for concrete structures for the storage of liquids: Part 4 Design tables Oct 2013 2 31 IS 3466:1988 Specification for masonry cement (second revision) Oct 2013 4 32 IS 3535:1986 Methods of sampling hydraulic cement (first revision) Oct 2013 33 IS 3558:1983 Oct 2013 34 IS 3812(Part 1):2013 Code of practice for use of immersion vibrators for consolidating concrete (first revision) Specification for pulverized fuel ash: Part 1 For use as pozzolana in cement, cement mortar and concrete (third revision) * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 6 No. of Amd. 3 Sl. No. IS Number/ DOC Number Title Reaffirm Date 35 IS 3812(Part 2):2013 Specification for pulverized fuel ash: Part 2 For use as admixture in cement mortar and concrete (third revision) 36 IS 4031(Part 1):1996 Methods of physical tests for hydraulic cement: Part 1 Determination of fineness by dry sieving (second revision) Feb 2011 37 IS 4031(Part 2):1999 Methods of physical tests for hydraulic cement: Part 2 Determination of fineness by specific surface by Blaine air permeability method (second revision) Oct 2013 1 38 IS 4031(Part 3):1988 Methods of physical tests for hydraulic cement: Part 3 Determination of soundness (first revision) Jul 2009 2 39 IS 4031(Part 4):1988 Methods of physical tests for hydraulic cement: Part 4 Determination of consistency of standard cement paste (first revision) Jul 2009 2 40 IS 4031(Part 5):1988 Methods of physical tests for hydraulic cement: Part 5 Determination of initial and final setting times (first revision) Jul 2009 2 41 IS 4031(Part 6):1988 Methods of physical tests for hydraulic cement: Part 6 Determination of compressive strength of hydraulic cement (other than masonry cement) (first revision) Jul 2009 4 42 IS 4031(Part 7):1988 Methods of physical tests for hydraulic cement: Part 7 Determination of compressive strength of masonry cement (first revision) Jul 2009 1 43 IS 4031(Part 8):1988 Methods of physical tests for hydraulic cement: Part 8 Determination of transverse and compressive strength of plastic mortar using prism (first revision) Jul 2009 1 44 IS 4031(Part 9):1988 Methods of physical tests for hydraulic cement: Part 9 Determination of heat of hydration (first revision) Jul 2009 45 IS 4031(Part 10):1988 Methods of physical tests for hydraulic cement: Part 10 Determination of drying shrinkage (first revision) Jul 2009 46 IS 4031(Part 11):1988 Methods of physical tests for hydraulic cement: Part 11 Determination of density (first revision) Jul 2009 47 IS 4031(Part 12):1988 Methods of physical tests for hydraulic cement: Part 12 Determination of air content of hydraulic cement mortar (first revision) Jul 2009 2 48 IS 4031(Part 13):1988 Methods of physical tests for hydraulic cement: Part 13 Measurement of water retentivity of masonry cement (first revision) Jul 2009 1 49 IS 4031(Part 14):1989 Methods of physical tests for hydraulic cement: Part 14 Determination of false set Jul 2009 1 50 IS 4031(Part 15):1991 Methods of physical test for hydraulic cement: Part 15 Determination of fineness by wet sieving Jul 2009 51 IS 4032:1985 Method of chemical analysis of hydraulic cement (first revision) Jul 2009 52 IS 4305:1967 Glossary of terms relating to pozzolana Jul 2009 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 7 No. of Amd. 1 2 Sl. No. IS Number/ DOC Number Title 53 Methods for testing performance of batch-type concrete mixers (first revision) Jul 2009 IS 4634:1991 Reaffirm Date 54 IS 4845:1968 Definitions and terminology relating to hydraulic cement Oct 2013 55 IS 4926:2003 Code of practice for ready mixed concrete (second revision) Apr 2012 56 IS 5512:1983 Specification for flow table for use in tests of hydraulic cements and pozzolanic materials (first revision) Oct 2013 57 IS 5513:1996 Specification for vicat apparatus (second revision) Feb 2011 58 IS 5514:1996 Specification for apparatus used in Le-Chatelier Test (first revision) Feb 2011 59 IS 5515:1983 Specification for compaction factor apparatus (first revision) Oct 2013 60 IS 5516:1996 Specification for variable flow type air-permeability apparatus (Blaine type) (first revision) Feb 2011 61 IS 5525:1969 Recommendations for detailing of reinforcement in reinforced concrete works Oct 2013 62 IS 5536:1969 Specification for constant flow type air-permeability apparatus (Lea and Nurse type) Jul 2009 63 IS 5816:1999 Method of test for splitting tensile strength of concrete (first revision) Oct 2013 64 IS 6452:1989 Specification for high alumina cement for structural use (first revision) Jul 2009 65 IS 6461(Part 1):1972 Glossary of terms relating to cement concrete: Part 1 Concrete aggregates Apr 2011 66 IS 6461(Part 2):1972 Glossary of terms relating to cement concrete: Part 2 Materials (other than cement and aggregate) Apr 2011 67 IS 6461(Part 3):1972 Glossary of terms relating to cement concrete: Part 3 Concrete reinforcement Apr 2011 68 IS 6461(Part 4):1972 Glossary of terms relating to cement concrete: Part 4 Types of concrete Apr 2011 69 IS 6461(Part 5):1972 Glossary of terms relating to cement concrete: Part 5 Formwork for concrete Apr 2011 70 IS 6461(Part 6):1972 Glossary of terms relating to cement concrete: Part 6 Equipment, tools and plant Apr 2011 71 IS 6461(Part 7):1973 Glossary of terms relating to cement concrete: Part 7 Mixing, laying, compaction, curing and other construction aspects Apr 2011 72 IS 6461(Part 8):1973 Glossary of terms relating to cement concrete: Part 8 Properties of concrete Apr 2011 73 IS 6461(Part 9):1972 Glossary of terms relating of cement concrete: Part 9 Structural aspects Apr 2011 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 8 No. of Amd. 1 5 Sl. No. IS Number/ DOC Number Title 74 IS 6461(Part 10):1973 Glossary of terms relating to cement concrete: Part 10 Tests and testing apparatus Apr 2011 75 IS 6461(Part 11):1973 Glossary of terms relating to cement concrete: Part 11 Prestressed concrete Apr 2011 76 IS 6461(Part 12):1973 Glossary of terms relating to cement concrete: Part 12 Miscellaneous Apr 2011 77 IS 6491:1972 Method of sampling fly ash Feb 2011 1 78 IS 6909:1990 Specification for supersulphated cement Feb 2011 5 79 IS 6925:1973 Methods of test for determination of water soluble chlorides in concrete admixtures Oct 2013 80 IS 7246:1974 Recommendations for use of table vibrators for consolidating concrete Oct 2013 81 IS 7320:1974 Specification for concrete slump test apparatus Oct 2013 82 IS 7325:1974 Specification for apparatus for determining constituents of fresh concrete Oct 2013 83 IS 7861(Part 1):1975 Code of practice for extreme weather concreting: Part 1 Recommended practice for hot weather concreting Apr 2011 1 84 IS 7861(Part 2):1981 Code of practice for extreme weather concreting: Part 2 Recommended practice for cold weather concreting Apr 2011 1 85 IS 8041:1990 Specification for rapid hardening Portland cement (second revision) Jul 2009 4 86 IS 8042:1989 Specification for white Portland cement (second revision) Jul 2009 6 87 IS 8043:1991 Specification for hydrophobic Portland cement (second revision) Jul 2009 3 88 IS 8112:2013 Specification for ordinary Portland cement, 43 grade (second revision) 89 IS 8125:1976 Dimensions and materials of cement rotary kilns, components and auxiliaries (dry process with suspension preheater) Oct 2013 90 IS 8142:1976 Method of test for determining setting time of concrete by penetration resistance Apr 2011 91 IS 8229:1986 Specification for oil-well cement (first revision) Oct 2013 92 IS 8425:1977 Code of practice for determination of specific surface area of powders by air permeability methods Feb 2011 93 IS 9012:1978 Recommended practice for shotcreting Apr 2011 1 94 IS 9013:1978 Method of making, curing and determining compressive strength of accelerated cured concrete test specimens Oct 2013 1 Specification for admixtures for concrete (first revision) Oct 2013 2 95 IS 9103:1999 Reaffirm Date * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS 1 1 ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 9 No. of Amd. 6 Sl No. IS Number/ DOC Number Title Reaffirm Date 96 IS 9142:1979 Specification for artificial light weight aggregates for concrete masonry units Apr 2011 97 IS 9284:1979 Method of test for abrasion resistance of concrete Apr 2011 98 IS 9376:1979 Specification for apparatus for measuring aggregate crushing value and ten percent fines value Oct 2013 99 IS 9377:1979 Specification for apparatus for aggregate impact value Oct 2013 100 IS 9399:1979 Specification for apparatus for flexural testing of concrete Oct 2013 101 IS 9459:1980 Specification for apparatus for use in measurement of length change of hardened cement paste, mortar and concrete Oct 2013 102 IS 9799:1981 Specification for pressure meter for determination of air content of freshly mixed concrete Oct 2013 103 IS 10070:1982 Specification for machine for abrasion testing of coarse aggregates Oct 2013 104 IS 10078:1982 Specification for jolting apparatus for testing cement Oct 2013 105 IS 10079:1982 Specification for cylindrical metal measures for use in tests of aggregates and concrete Oct 2013 106 IS 10080:1982 Specification for vibration machine for casting standard cement mortar cubes Oct 2013 5 107 IS 10086:1982 Specification for moulds for use in tests of cement and concrete Oct 2013 5 108 IS 10262:2009 Guidelines for concrete mix proportioning (first revision) 109 IS 10510:1983 Specification for vee-bee consistometer Oct 2013 110 IS 10850:1984 Specification for apparatus for measurement of water retentivity of masonry cement Oct 2013 111 IS 10890:1984 Specification for planetary mixer used in tests of cement and pozzolana Oct 2013 112 IS 11262:1985 Specification for calorimeter for determination of heat of hydration of hydraulic cement Oct 2013 113 IS 11263:1985 Specification for cylinder measures for determination of air content of hydraulic cement mortar Oct 2013 114 IS 11578:1986 Method for determination of specific surface area of powder and porous particle using low temperature gas absorption Apr 2011 115 IS 11993:1987 Code of practice for use of screed board concrete vibrators Oct 2013 116 IS 12089:1987 Specification for granulated slag for manufacture of Portland slag cement Oct 2013 117 IS 12119:1987 General requirements for pan mixers for concrete Oct 2013 118 IS 12269:2013 Specification for ordinary Portland cement, 53 grade (first revision) * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 10 No. of Amd. 2 1 Sl No. IS Number/ DOC Number Title Reaffirm Date 119 IS 12303:1987 Criteria for design of RCC hinges Apr 2012 120 IS 12330:1988 Specification for sulphate resisting Portland cement Jul 2009 121 IS 12423:1988 Method for colorimetric analysis of hydraulic cement Jul 2009 122 IS 12600:1989 Specification for low heat Portland cement Jul 2009 123 IS 12803:1989 Methods of analysis of hydraulic cement by X-ray fluorescence spectrometer Oct 2013 124 IS 12813:1989 Method of analysis of hydraulic cement by atomic absorption spectrophotometer Oct 2013 125 IS 12870:1989 Methods of sampling calcined clay pozzolana Feb 2011 126 IS 13311(Part 1):1992 Oct 2013 127 IS 13311(Part 2):1992 128 IS 14345:1996 Methods of non-destructive testing of concrete: Part 1 Ultrasonic pulse velocity Methods of non-destructive testing of concrete: Part 2 Rebound hammer Specification for autoclave apparatus 129 IS 14687:1999 Guidelines for falsework for concrete structures 130 IS 14858:2000 Requirements for compression testing machine used for testing of concrete and mortar Feb 2011 131 IS 14959(Part 1):2001 Method of test for determination of water soluble and acid soluble chlorides in mortar and concrete: Part 1 Fresh mortar Apr 2011 1 132 IS 14959(Part 2):2001 Method of test for determination of water soluble and acid soluble chlorides in mortar and concrete: Part 2 Hardened mortar and concrete Apr 2011 1 133 IS 15388:2003 Specification for silica fume Apr 2012 134 SP 23(S&T): 1982 Handbook on concrete mixes (Based on Indian Standards) 135 SP 34(S&T): 1987 Handbook on concrete reinforcement and detailing DOC.CED 2(7921) Metakaolin for use in cement, cement mortar and concrete - Specification 2 DOC.CED 2(7922) Portland cement clinker - Specification DOC.CED 2(7164) Draft Amendment No. 7 to IS 455:1989 2 DOC.CED 2(7165) Draft Amendment No. 6 to IS 1489(Part 1):1991 Jul 2009 DRAFT ISSUED IN WIDE CIRCULATION 1 DOC.CED 2(7919) Third Revision of IS 383 2 DOC.CED 2(7920) Draft Amendment No. 3 to IS 2386(Part 7):1963 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 11 5 Feb 2011 DRAFT STANDARDS FINALIZED BUT NOT YET UNDER PRINT 1 6 Oct 2013 FINALIZED DRAFT UNDER PRINT 1 No. of Amd. 1 CED 3 SANITARY APPLIANCES AND WATER FITTINGS SCOPE - GLAZED EARTHENWARE SANITARY APPLIANCES, WATER CLOSETS, ENAMELLED CAST IRON RAILWAY COACHING STOCK , WOODEN, PLASTIC ETC, BATH TUBS, VITREOUS SANITARY APPLIANCES, NONFERROUS WASTE FITTINGS FOR WASH BASINS AND SINKS, TRAPS WASTE PLUG AND ACCESSORIES FOR WASH BASINS, FLUSHING CISTERNS, MANHOLE COVERS FOR USE IN DRAINAGE WORKS (EXCEPT CONCRETE), PILLAR TAPS, BALL VALVES, COPPER AND PLASTIC FLOATS FOR BALL VALVES, CAULKING LEAD, FERRULES, PLUG COCKS, FOOT VALVES, SURFACE BOXES, STONEWARE PIPES, WATER METERS, WATER METER BOX, SLUICE VALVES, GLAZED EARTHENWARE TILES. Sl. No. IS Number/ DOC Number Title Reaffirm Date No. of Amd. STANDARDS PUBLISHED 1 IS 651:2007 Glazed stoneware pipe and fittings - Specification (sixth revision) Oct 2012 2 IS 771(Part 1):1979 Specification for glazed fire-clay sanitary appliances: Part 1 General requirements (second revision) Oct 2012 1 3 IS 771(Part 2):1985 Specification for glazed fire-clay sanitary appliances: Part 2 Specific requirements of kitchen and laboratory sinks (third revision) Oct 2013 3 4 IS 771(Part 3/Sec 1):1979 Specification for glazed fire clay sanitary appliances : Part 3 Specific requirements of urinals, Section 1 Slab urinals (second revision) Oct 2012 5 IS 771(Part 3/Sec 2):1985 Specification for glazed fire-clay sanitary appliances: Part 3 Specific requirements of urinals: Section 2 Stall urinals (third revision) Jul 2010 6 IS 771(Part 4):1979 Specification for glazed fire-clay sanitary appliances: Part 4 Specific requirements of postmortem slabs (second revision) Oct 2012 7 IS 771(Part 5):1979 Specification for glazed fire clay sanitary appliances: Part 5 Specific requirements of shower trays (second revision) Oct 2012 8 IS 771(Part 6):1979 Specification for glazed fire-clay sanitary appliances: Part 6 Specific requirements of bed-pan sinks (second revision) Jul 2010 9 IS 771(Part 7):1981 Specification for glazed fire-clay sanitary appliances: Part 7 Specific requirements of slop sinks (second revision) Oct 2012 10 IS 772:1973 Specification for general requirements for enamelled cast iron sanitary appliances (second revision) Oct 2012 1 11 IS 774:2004 Specification for flushing cistern for water closets and urinals (other than plastic cistern) (fifth revision) Nov 2009 1 12 IS 778:1984 Specification for copper alloy gate, globe and check valves for water works purposes (fourth revision) Jul 2010 4 13 IS 779:1994 Specification for water meters (domestic type) (sixth revision) Jul 2009 5 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 12 Sl. No. IS Number/ DOC Number Title Reaffirm Date 14 IS 781:1984 Specification for cast copper alloy screw down bib taps and stop valves for water services (third revision) Jul 2010 15 IS 782:1978 Specification for caulking lead (third revision) Oct 2012 16 IS 1701:1960 Specification for mixing valves for ablutionary and domestic purposes Oct 2012 17 IS 1703:2000 Water fittings - copper alloy float valves (horizontal plunger type) - Specification (fourth revision) Jul 2010 18 IS 1711:1984 Specification for self-closing taps for water supply purposes (second revision) Jul 2010 19 IS 1726:1991 Specification for cast iron manhole covers and frames (third revision) Oct 2012 20 IS 1795:1982 Specification for pillar taps for water supply purposes (second revision) Jul 2010 21 IS 2326:1987 Specification for automatic flushing cisterns for urinals (other than plastic cisterns) (second revision) Oct 2013 22 IS 2373:1981 Specification for water meters (bulk type) (third revision) Oct 2012 23 IS 2548(Part 1):1996 Specification for plastic seats and covers for water-closets: Part 1 Thermoset seats and covers (fifth revision) Jul 2011 24 IS 2548(Part 2):1996 Specification for plastic seats and covers for water-closets: Part 2 Thermo plastic seats and covers (fifth revision) Jul 2011 1 25 IS 2556(Part 1):1994 Specification for vitreous sanitary appliances (vitreous china): Part 1 General requirements (third revision) Jul 2011 5 26 IS 2556(Part 2):2004 Specification for vitreous sanitary appliances (vitreous china): Part 2 Specific requirements of wash-down water-closets (fifth revision) Sep 2009 2 27 IS 2556(Part 3):2004 Specification for vitreous sanitary appliances (vitreous china): Part 3 Specific requirements of squatting pans (fifth revision) Sep 2009 28 IS 2556(Part 4):2004 Specification for vitreous sanitary appliances (vitreous china): Part 4 Specific requirements of wash basins (fourth revision) Oct 2009 2 29 IS 2556(Part 5):1994 Specification for vitreous sanitary appliances (vitreous china): Part 5 Specific requirements of laboratory sinks (third revision) Jul 2009 3 30 IS 2556(Part 6):1995 Specification for vitreous sanitary appliances (vitreous china): Part 6 Specific requirements of urinals and partition plates (fourth revision) Oct 2013 2 31 IS 2556(Part 7):1995 Specification for vitreous sanitary appliances (vitreous china): Part 7 Specific requirements of accessories for sanitary appliances (third revision) Oct 2013 3 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 13 No. of Amd. 2 1 3 Sl No. IS Number/ DOC Number Title Reaffirm Date 32 IS 2556(Part 8):2004 Specification for vitreous sanitary appliances (vitreous china): Part 8 Specific requirements of pedestal close coupled washdown and syphonic water closets (fifth rivision) Sep 2009 33 IS 2556(Part 9):2004 Specification for vitreous sanitary appliances (vitreous china): Part 9 Specific requirements of pedestal type bidets (fifth revision) Oct 2009 34 IS 2556(Part 14):1995 Specification for vitreous sanitary appliances (vitreous china): Part 14 Specific requirements of integrated squatting pans (first revision) Jul 2010 1 35 IS 2556(Part 15):2004 Specification for vitreous sanitary appliances (vitreous china): Part 15 Specific requirements of universal water closets (second revision) Sep 2009 1 36 IS 2556(Part 16):2002 Specification for vitreous sanitary appliances (vitreous china): Part 16 Specific requirements for wash down wall mounted water closets Oct 2012 37 IS 2556(Part 17):2001 Specification for vitreous sanitary appliances (vitreous china): Part 17 Specific requirements for wall mounted bidets Jul 2011 38 IS 2685:1971 Code of practice for selection, installation and maintenance of sluice valves (first revision) Oct 2012 2 39 IS 2692:1989 Specification for ferrules for water services (second Revision) Oct 2013 3 40 IS 2963:2013 Copper alloy waste fittings and waste plug for wash basin and sinks- Specification (second revision) (amalgamating IS 3311) 41 IS 3004:1979 Specification for plug cocks for water supply purposes (first revision) Jul 2010 42 IS 3006:1979 Specification for chemically resistant glazed stoneware pipes and fittings (first revision) Oct 2012 43 IS 3042:1965 Specification for single faced sluice gates (200 to 1200 mm) Oct 2013 44 IS 3950:1979 Specification for surface boxes for sluice valves (first revision) Oct 2012 45 IS 4038:1986 Specification for foot valves for water works purposes (second revision) Jul 2010 46 IS 4346:1982 Specification for washers for use with fittings for water services (first revision) Jul 2010 47 IS 5219:2013 Cast copper alloys traps - Specification (first revision) 48 IS 5312(Part 1):2004 Specification for swing check type reflux (non-return) valves: Part 1 Single door pattern (second revision) 49 IS 5312(Part 2):2013 Swing check type reflux (non-return) valves for water works purposes-Specification: Part 2 Multi door pattern (first revision) * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS Nov 2009 ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 14 No. of Amd. 1 2 Sl No. IS Number/ DOC Number Title 50 IS 5455:1969 Specification for cast-iron steps for manholes 51 IS 5961:1970 Specification for cast iron gratings for drainage purposes Oct 2012 52 IS 6411:1985 Specification for gel-coated glass fibre reinforced polyester resin bath tubs (first revision) Jul 2010 53 IS 6784:1996 Method for performance testing of water meters (domestic type) (second revision) Jul 2011 1 54 IS 7231:1994 Specification for plastic flushing cisterns for water closets and urinals (second revision) Jul 2009 4 55 IS 8931:1993 Specification for copper alloy fancy single taps, combination tap assembly and stop valves for water services (first revision) Oct 2013 1 56 IS 9140:1996 Method of sampling of vitreous and fire clay sanitary appliances (second revision) Jul 2011 57 IS 9338:2013 Cast iron/S.G. Iron/Cast Steel screw-down stop valves for water works purposes - Specification (second revision) 58 IS 9739:1981 Specification for pressure reducing valves for domestic water supply systems Oct 2012 3 59 IS 9758:1981 Specification for flush valves and fittings for water closets and urinals Oct 2012 2 60 IS 9762:1994 Specification for polyethylene floats (spherical) for float valves (first revision) Jul 2009 61 IS 9763:2000 Plastic bib taps, pillar taps, angle valves and stop valves for hot and cold water services - Specification (second revision) Jul 2010 62 IS 11246:1992 Specification for glass fibre reinforced polyester resins (GRP) squatting pans (first revision) Oct 2012 63 IS 12234:1988 64 IS 12701:1996 Specification for rotational moulded polyethylene water storage tanks (first revision) Jul 2011 2 65 IS 13049:1991 Specification for diaphragm type (plastic body) float operated valves for cold water services Oct 2012 2 66 IS 13114:1991 Specification for forged brass gate, globe and check valves for water works purposes Oct 2012 67 IS 13349:1992 Specification for single faced cast iron thimble mounted sluice्gates Oct 2012 1 68 IS 13983:1994 Specification for stainless steel sinks for domestic purposes Jul 2009 3 69 IS 14399(Part 1):1996 Hot press moulded thermosetting glass fibre reinforced polyester resin (GRP) sectional water storage tanks: Part 1 Specification for panels Jul 2011 1 Specification for plastic equilibrium float valve for cold water services 15 Reaffirm No. of Date Amd. Oct 2012 1 Oct 2013 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS Sl No. IS Number/ DOC Number Title Reaffirm Date 70 IS 14399(Part 2):1996 Hot press moulded thermosetting glass fibre reinforced (GRP) sectional water storage tanks: Part 2 Guidelines for assembly, installation and testing Jul 2011 71 IS 14845:2000 Resilient seated cast iron air relief valves for water works purposes - Specification Jul 2010 1 72 IS 14846:2000 Sluice valves for water works purposes (50-1200 mm) Specification Jul 2010 4 FINALISED DRAFTS UNDER PRINT 1 DOC.CED 3(7742) Draft Amendment No. 3 to IS 2556(Part 4):2004 2 DOC.CED 3(7848) Draft Amendment No. 2 to IS 774:2004 3 DOC.CED 3(7849) Draft Amendment No. 5 to IS 7231:1994 DRAFT ISSUED IN WIDE CIRCULATION 1. DOC.CED 3(7744)R Draft Amendment No. 2 to IS 2548 (Part 2):1996 2. DOC.CED 3(7936) Draft Amendment No. 2 to IS 2556 (Part 15)2004 3. DOC.CED 3(7937) Draft Amendment No. 1 to IS 2548(Part 1): 1996 4. DOC.CED 3(7938) Draft Amendment No. 6 to IS 7231: 1994 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 16 No. of Amd. CED 4 BUILDING LIME AND GYPSUM PRODUCTS SCOPE - SUBJECTS PERTAINING TO: 1) MANUFACTURE OF BUILDING LIME AND LIME PRODUCTS 2) SUPPLY AND STORAGE OF BUILDING LIME, AND 3) USE OF BUILDING LIME AND LIME PRODUCTS ON CONSTRUCTION WORKS 4) GYPSUM BUILDING MATERIAL; 5) GYPSUM PLASTER BOARD, NON-LOAD BEARING GYPSUM PLASTER BLOCK 6) GLOSSARY OF TERMS RELATING TO LIME AND GYPSUM 7) GYPSUM PLASTER, AND 8) METHOD OF TEST FOR GYPSUM PLASTER CONCRETE AND PRODUCTS, GYPSUM TILES AND REINFORCED BLOCKS Sl No. IS Number/ DOC Number Title Reaffirm Date No. of Amd. STANDARDS PUBLISHED 1 IS 712:1984 Specification for building limes (third revision) May 2009 1 2 IS 1624:1986 Method of field testing of building lime (second revision) May 2009 2 3 IS 1635:1992 Code of practice for field slaking of building lime and preparation of putty (second revision) Jan 2014 4 IS 1849(Part 1/Sec 1):1990 Guide for design and installation of vertical mixed-feed lime kiln: Part 1 Limestone Section 1 Masonry type shaft (second revision) Jan 2014 5 IS 1849(Part 1/Sec 2):1991 Guide for design and installation of vertical mixed feed type lime kiln: Part 1 For limestone Section 2 RCC type shaft Apr 2010 6 IS 1861(Part 1):1990 Guide for manufacture of lime in vertical mixed-feed type kiln: Part 1 From lime-stone (second revision) Apr 2010 7 IS 2095(Part 1):2011 Specification for gypsum plaster boards: Part 1 Plain gypsum plaster boards (third revision) 8 IS 2095(Part 2):2001 Specification for gypsum plaster boards: Part 2 Coated/ laminated gypsum plaster boards (second revision) Jan 2012 2 9 IS 2095(Part 3):1996 Specification for gypsum plaster boards Part 3 Reinforced gypsum plaster boards (second revision) May 2009 2 10 IS 2469:1976 Glossary of terms relating to gypsum (first revision) Jan 2012 11 IS 2541:1991 Code of practice for preparation and use of lime concrete (second revision) May 2009 3 12 IS 2542(Part 1/Sec 1):1978 Methods of test for gypsum plaster, concrete and products: Part 1 Plaster and Concrete: Sec 1 Normal consistency of gypsum plaster (first revision) Jan 2012 1 13 IS 2542(Part 1/Sec 2):1978 Methods of test for gypsum plaster, concrete and products: Part 1 Plaster and Concrete: Sec 2 Normal consistency of gypsum concrete (first revision) Jan 2012 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 17 1 Sl No. IS Number/ DOC Number Title 14 IS 2542(Part 1/Sec 3):1978 Methods of test for gypsum plaster, concrete and products: Part 1 Plaster and Concrete: Sec 3 Setting time of plaster and concrete (first revision) Jan 2012 15 IS 2542(Part 1/Sec 4):1978 Methods of test for gypsum plaster, concrete and products: Part 1 Plaster and Concrete: Sec 4 Transverse strength of gypsum plaster (first revision) Jan 2012 16 IS 2542(Part 1/Sec 5):1978 Methods of test for gypsum plaster, concrete and products: Part 1 Plaster and Concrete: Sec 5 Compressive strength and dry set density of gypsum plaster (first revision) Jan 2012 17 IS 2542(Part 1/Sec 6):1978 Methods of test for gypsum plaster, concrete and products: Part 1 Plaster and Concrete: Sec 6 Soundness of gypsum plaster (first revision) Jan 2012 18 IS 2542(Part 1/Sec 7):1978 Methods of test for gypsum plaster, concrete and products: Part 1 Plaster and Concrete: Sec 7 Mechanical resistance of gypsum plaster by dropping ball test (first revision) Jan 2012 19 IS 2542(Part 1/Sec 8):1978 Methods of test for gypsum plaster, concrete and products: Part 1 Plaster and Concrete: Sec 8 Freedom from coarse particles (first revision) Jan 2012 20 IS 2542(Part 1/Sec 9):1978 Methods of test for gypsum plaster, concrete and products: Part 1 Plaster and Concrete: Sec 9 Expansion of plaster (first revision) Jan 2012 21 IS 2542(Part 1/Sec 10):1978 Methods of test for gypsum plaster, concrete and products: Part 1 Plaster and Concrete: Sec 10 Sand in set plaster (first revision) Jan 2012 22 IS 2542(Part 1/Sec 11):1978 Methods of test for gypsum plaster, concrete and products: Part 1 Plaster and Concrete: Sec 11 Wood fibre content in wood fibre gypsum plaster (first revision) Jan 2012 23 IS 2542(Part 1/Sec 12):1978 Methods of test for gypsum plaster, concrete and products: Part 1 Plaster and Concrete: Sec 12 Dry bulk density (first revision) Jan 2012 Methods of test for gypsum plaster, concrete and products : Part 2 Gypsum products : Sec 1 Measurement of dimensions (first revision) Jan 2012 24 IS 2542(Part 2/Sec 1):1981 Reaffirm Date 25 IS 2542(Part 2/Sec 2):1981 Methods of test for gypsum plaster, concrete and products : Part 2 Gypsum products : Sec 2 Determination of mass (first revision) Jan 2012 26 IS 2542(Part 2/Sec 3):1981 Methods of test for gypsum plaster, concrete and products : Part 2 Gypsum products : Sec 3 Determination of mass and thickness of paper surfacing (first revision) Jan 2012 27 IS 2542(Part 2/Sec 4):1981 Methods of test for gypsum plaster, concrete and products : Part 2 Gypsum products : Sec 4 Transverse strength (first revision) Jan 2012 28 IS 2542(Part 2/Sec 5):1981 Methods of test for gypsum plaster, concrete and products : Part 2 Gypsum products : Sec 5 Compressive strength (first revision) Jan 2012 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 18 No. of Amd. 1 Sl No. IS Number/ DOC Number Title Reaffirm Date 29 IS 2542(Part 2/Sec 6):1981 Methods of test for gypsum plaster, concrete and products : Part 2 Gypsum products : Sec 6 Water absorption (first revision) Jan 2012 30 IS 2542(Part 2/Sec 7):1981 Methods of test for gypsum plaster, concrete and products : Part 2 Gypsum products : Sec 7 Moisture content (first revision) Jan 2012 31 IS 2542(Part 2/Sec 8):1981 Methods of test for gypsum plaster, concrete and products : Part 2 Gypsum products : Sec 8 Nail retention of precast reinforced gypsum slabs (first revision) Jan 2012 32 IS 2547(Part 1):1976 Specification for gypsum building plaster: Part 1 Excluding premixed lightweight plaster (first revision) Jan 2012 3 33 IS 2547(Part 2):1976 Specification for gypsum building plaster: Part 2 Premixed lightweight plaster (first revision) Jan 2012 1 34 IS 2686:1977 Specification for cinder as fine aggregates for use in lime concrete (first revision) Jan 2014 1 35 IS 2849:1983 Specification for non-load bearing gypsum partition blocks (solid and hollow types) (first revision) Jan 2012 4 36 IS 3068:1986 Specification for broken brick (burnt clay) coarse aggregates for use in lime concrete (second revision) May 2009 1 37 IS 3115:1992 Specification for lime based blocks (second revision) Jan 2014 1 38 IS 3182:1986 Specification for broken brick (burnt clay) fine aggregates for use in lime mortar (second revision) May 2009 1 39 IS 4098:1983 Specification for lime-pozzolana mixture (first revision) May 2009 3 40 IS 4139:1989 Specification for calcium silicate bricks (second revision) May 2009 1 41 IS 5817:1992 Code of practice for preparation and use of lime-pozzolana mixture concrete in buildings and roads (first revision) Jul 2009 2 42 IS 6508:1988 Glossary of terms relating to building lime (first revision) Jan 2014 43 IS 6932(Part 1):1973 Method of test for building limes Part 1 Determination of insoluble residue, loss on ignition, insoluble matter, silicone dioxide, ferric and aluminium oxide, calcium oxide and magnesium May 2009 3 44 IS 6932(Part 2):1973 Method of test for building limes: Part 2 Determination of carbon dioxide content May 2009 1 45 IS 6932(Part 3):1973 Method of test for building limes: Part 3 Determination of residue on slaking of quicklime May 2009 1 46 IS 6932(Part 4):1973 Method of test for building limes: Part 4 Determination of fineness of hydrated lime May 2009 2 47 IS 6932(Part 5):1973 Method of test for building limes: Part 5 Determination of unhydrated oxide May 2009 1 48 IS 6932(Part 6):1973 Method of test for building limes: Part 6 Determination of volume yield of quicklime May 2009 1 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 19 No. of Amd. 1 Sl No. IS Number/ DOC Number Title Reaffirm Date 49 IS 6932(Part 7):1973 Method of test for building limes: Part 7 Determination of compressive and transverse strength May 2009 4 50 IS 6932(Part 8):1973 Method of test for building limes: Part 8 Determination of workability May 2009 1 51 IS 6932(Part 9):1973 Method of test for building limes: Part 9 Determination of soundness May 2009 1 52 IS 6932(Part 10):1973 Method of test for building limes: Part 10 Determination of popping and pitting of hydrated lime May 2009 1 53 IS 6932(Part 11):1984 Method of test for building limes: Part 11 Determination of setting time of hydrated lime May 2009 1 54 IS 8272:1984 Specification for gypsum plaster for use in the manufacture of fibrous plaster boards (first revision) Jan 2012 1 55 IS 9498:1980 Specification for inorganic aggregates for use in gypsum plaster Jan 2012 1 56 IS 10049:1981 Code of practice for manufacture of lime based blocks Jan 2014 3 57 IS 10359:1982 Code of practice for manufacture and use of lime-pozzolana concrete blocks for paving Jul 2009 4 58 IS 10360:1982 Specification for lime-pozzolana concrete blocks for paving Jul 2009 4 59 IS 10772:1983 Specification for quick setting lime pozzolana mixture May 2009 3 60 IS 12654:1989 Code of practice for use of low grade gypsum in building industry Sep 2010 1 61 IS 12679:1989 Specification for By-product gypsum for use in plaster, blocks and boards Sep 2010 62 IS 12894:2002 Specification for pulverized fuel ash lime bricks (first revision) Jan 2012 63 IS 13001:1991 Guidelines for manufacture of gypsum plaster in mechanized pan system Jan 2012 64 IS 14401:1996 Guidelines for handling and storage of building limes Jan 2012 65 IS 14860:2000 Guidelines on fuel saving in vertical mixed-feed lime shaft kilns May 2009 66 IS 15648:2006 Specification for pulverized fuel ash for lime pozzolana mixture applications Sep 2010 FINALISED DRAFT UNDER PRINT 1 DOC.CED 4(7782) Draft Indian Standard Code of Practice for Dry Lining and Partitioning using Gypsum Plasterboards * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 20 No. of Amd. 1 1 CED 5 FLOORING, WALL FINISHING AND ROOFING SCOPE - STANDARDIZATION IN THE FIELD OF FLOORING MADE OF MATERIALS SUCH AS CONCRETE, CONCRETE TILES, MAGNESIUM OXYCHLORIDE, LINOLEUM, RUBBER, BITUMEN MASTIC AND PLASTICS; ACID AND ALKALI RESISTING FLOORING INCLUDING ACID RESISTING PLASTERS, WALL FINISHING, BITUMEN IMPREGNATED ROOFING SHEETS, PLASTICS BASED ROOFING SHEETS ETC, (EXCLUDING METAL AND ASBESTOS CEMENT SHEETS) AND THE RELATED CODES OF PRACTICES LIAISON: ISO/TC 189 (O) CERAMIC TILES Sl No. IS Number/ DOC Number Title Reaffirm Date No. of Amd. STANDARDS PUBLISHED 1 IS 653:1992 Specification for linoleum sheets and tiles (third revision) Jul 2011 2 IS 657:1982 Specification for materials for use in the manufacture of magnesium oxychloride flooring compositions (second revision) Jul 2011 3 IS 658:1982 Code of practice for magnesium oxychloride composition floors (second revision) Jul 2011 4 IS 809:1992 Specification for rubber flooring materials for general purposes (first revision) Jul 2011 5 IS 1195:2002 Bitumen-mastic for flooring - Specification (third revision) Nov 2012 6 IS 1196:1978 Code of practice for laying bitumen mastic flooring (second revision) Jul 2011 7 IS 1197:1970 Code of practice for laying of rubber floors (first revision) Jul 2011 8 IS 1198:1982 Code of practice for laying, fixing and maintenance of linoleum floors (first revision) Jul 2011 9 IS 1237:2012 Specification for cement concrete flooring tiles (second revision)्््््््््Mar्2012्््््््््् 10 IS 1443:1972 Code of practice for laying and finishing of cement concrete flooring tiles (first revision) 11 IS 1542:1992 Specification for sand for plaster (second revision) 12 IS 1630:1984 Specification for mason's tools for plaster work and pointing work (first revision) Jul 2011 13 IS 1661:1972 Code of practice for application of cement and cement-lime plaster finishes (first revision) Jul 2011 14 IS 2114:1984 Code of practice for laying in-situ terrazzo floor finish (first revision) Jul 2011 15 IS 2394:1984 Code of practice for application of lime plaster finish (first revision) Jul 2011 16 IS 2402:1963 Code of practice for external rendered finishes Jul 2011 * INDICATES STANDARDS UNDER REVISION Jul 2011 Feb 2014 ** INDICATES STANDARDS TO BE REVISED 21 1 1 / INDICATES DUAL NUMBER STANDARDS | INDICATES EQUIVALENT STANDARDS Sl No. IS Number/ DOC Number Title Reaffirm Date 17 IS 2571:1970 Code of practice for laying in-situ cement concrete flooring (first revision) Jul 2011 18 IS 3461:1980 Specification for PVC asbestos floor tiles (first revision) Jul 2011 4 19 IS 3462:1986 Specification for unbacked flexible PVC flooring (second revision) Jul 2011 1 20 IS 3464:1986 Methods of test for plastic flooring and wall tiles (second revision) Jul 2011 2 21 IS 4441:1980 Code of practice for use of silicate type chemical resistant mortars (first revision) Jul 2011 1 22 IS 4442:1980 Code of practice for use of sulphur type chemical resistant mortars (first revision) Jul 2011 23 IS 4443:1980 Code of practice for use of resin type chemical resistant mortars (first revision) Jul 2011 1 24 IS 4456(Part 1I):1967 Methods of test for chemical resistant mortars: Part 1 Silicate type and resin type Jul 2011 1 25 IS 4456(Part 2):1967 Methods of test for chemical resistant mortars: Part 2 Sulphur type Jul 2011 26 IS 4457:2007 Ceramic unglazed vitreous acid resisting tile - Specification (second revision) Jun 2012 27 IS 4631:1986 Code of practice for laying of epoxy resin floor toppings (first revision) Jul 2011 28 IS 4832(Part 1):1969 Specification for chemical resistant mortars: Part 1 Silicate type Jul 2011 1 29 IS 4832(Part 2):1969 Specification for chemical resistant mortars: Part 2 Resin type Jul 2011 1 30 IS 4832(Part 3):1968 Specification for chemical resistant mortars: Part 3 Sulphur type Jul 2011 1 31 IS 4860:1968 Specification for acid-resistant bricks Jul 2011 32 IS 4971:2007 Recommendations for selection of industrial floor finishes (first revision) Jun 2012 33 IS 5317:2002 Specification for pitch-mastic for bridge decking and roads (second revision) Nov 2012 34 IS 5318:1969 Code of practice for laying of flexible PVC sheet and tile Jul 2011 35 IS 5491:1969 Code of practice for laying of in-situ granolithic concrete floor topping Jul 2011 36 IS 5766:1970 Code of practice for laying burnt clay brick flooring Jul 2011 37 IS 6278:1971 Code of practice for white-washing and colour washing Jul 2011 38 IS 7956:1975 Recommendations for selection of dairy floor finishes Jul 2011 39 IS 8374:1977 Specification for bitumen mastic, anti-static and electrically conducting grade Jul 2011 22 No. of Amd. * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS Sl No. IS Number/ DOC Number Title Reaffirm Date 40 IS 9162:1979 Methods of tests for epoxy resins, hardeners and epoxy resin compositions for floor topping Jul 2011 41 IS 9197:1979 Specification for epoxy resin, hardners and epoxy resin compositions for floor topping Jul 2011 42 IS 9510:1980 Specification for bitumen mastic, acid-resisting grade Jul 2011 43 IS 9704:1980 Methods of tests for linoleum sheets and tiles Jul 2011 44 IS 10132:1982 Method of test for materials for use in the preparation of magnesium oxychloride flooring compositions Jul 2011 45 IS 10403:1983 Glossary of terms relating to building finishes Jul 2011 46 IS 12583:1988 Specification for corrugated bitumen roofing sheets Feb 2014 2 47 IS 12866:1989 Specification for plastic translucent sheets made from thermosetting polyester resin (glass fibre reinforced) Feb 2014 1 48 IS 13026:1991 Specification for bitumen mastic for flooring for industries handling LPG and other light hydrocarbon products Jul 2011 1 49 IS 13074:1991 Code of practice for laying of bitumen mastic flooring for industries handling LPG and other light hydrocarbon products Jul 2011 50 IS 13630(Part 1):2006 | 10545-2 Ceramic Tiles - Methods of Test, Sampling and Basis for Acceptance Part 1 Determination of dimensions and surface quality (first revision) Jan 2012 51 IS 13630(Part 2):2006 | 10545-3 Ceramic Tiles - Methods of Test, Sampling and Basis for Acceptance Part 2 Determination of water absorption and bulk density (first revision) Jan 2012 52 IS 13630(Part 3):2006 | 10545-10 Ceramic Tiles - Methods of Test, Sampling and Basis for Acceptance Part 3 Determination of moisture expansion using boiling water (first revision) Jan 2012 53 IS 13630(Part 4):2006 | 10545-8 Ceramic Tiles - Methods of Test, Sampling and Basis for Acceptance Part 4 Determination of linear thermal expansion (first revision) Jan 2012 54 IS 13630(Part 5):2006 | 10545-9 Ceramic Tiles - Methods of Test, Sampling and Basis for Acceptance Part 5 Determination of resistance to thermal shock (first revision) Jan 2012 55 IS 13630(Part 6):2006 | 10545-4 Ceramic Tiles - Methods of Test, Sampling and Basis for Acceptance Part 6 Determination of modulus of rupture and breaking strength (first revision) Jan 2012 56 IS 13630(Part 7):2006 | 10545-13 Ceramic Tiles - Methods of Test, Sampling and Basis for Acceptance Part 7 Determination of chemical resistance unglazed tiles (first revision) Jan 2012 57 IS 13630(Part 8):2006 | 10545-13&14 Ceramic Tiles - Methods of Test, Sampling and Basis for Acceptance Part 8 Determination of chemical resistance glazed tiles (first revision) Jan 2012 58 IS 13630(Part 9):2006 | 10545-11 Ceramic Tiles - Methods of Test, Sampling and Basis for Acceptance Part 9 Determination of crazomg resistance glazed tiles (first revision) Jan 2012 23 No. of Amd. 2 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS Sl No. IS Number/ DOC Number Title 59 IS 13630(Part 10):2006 | 10545-12 Ceramic Tiles - Methods of Test, Sampling and Basis for Acceptance Part 10 Determination of frost resistance (first revision) Jan 2012 60 IS 13630(Part 11):2006 | 10545-7 Ceramic Tiles - Methods of Test, Sampling and Basis for Acceptance Part 11 Determination of resistance of surface abrasion - Glazed tiles (first revision) Jan 2012 61 IS 13630(Part 12):2006 | 10545-6 Ceramic Tiles - Methods of Test, Sampling and Basis for Acceptance Part 12 Determination of resistance to deep abrasion - Unglazed tiles (first revision) Jan 2012 62 IS 13630(Part 13):2006 Jan 2012 63 IS 13630(Part 14):2006 | 10545-5 Ceramic Tiles - Methods of Test, Sampling and Basis for Acceptance Part 13 Determination of scratch hardness of surface according to MOHS (first revision) Ceramic Tiles - Methods of Test, Sampling and Basis for Acceptance Part 14 Determination of impact resistance by measurement of coefficient of restitution 64 IS 13630(Part 15):2006 | 10545-1 Ceramic Tiles - Methods of Test, Sampling and Basis for Acceptance Part 15 Ceramic tiles sampling and basis for acceptance {Superseding IS 13711:1993) Jan 2012 65 IS 13712:2006 | ISO 13006 Ceramic tiles - Definitions, classifications, characteristics and marking (first revision) Jan 2012 66 IS 13801:2013 Chequered cement concrete tiles - Specification (first revision) May 2013 67 IS 15193:2002 Code of practice for laying of pitch-mastic flooring for industries handling heavy hydrocarbon product like kerosene, diesel and furnace oil Nov 2012 68 IS 15194:2002 Reaffirm Date Pitch-mastic flooring and industries handling heavy hydrocarbon products like kerosene, diesel and furnace oil - Jan 2012 Nov 2012 69 IS 15224:2002 Laying of plastic translucent sheets made from thermosetting polyester resin (glass fibre reinforced) alone or in conjunction with asbestos cement sheets/steel sheets/aluminium sheets Code of practice Nov 2012 70 IS 15401:2003 Wall coverings in roll forms - Vocabulary and symbols Feb 2014 71 IS 15418:2003 Wall coverings in roll form for finished wall papers, wall vinyls and plastic wall coverings - Specification Feb 2014 Adhesives for use with ceramic tiles and mosaics-Specification Apr 2010 Pressed ceramic tiles - Specification (Superseding IS 13753, IS 13754, IS 13755 and IS 13756) Jul 2011 Precast concrete blocks for paving - Specification Jul 2011 72 IS 15477:2004 73 IS 15622:2006 | ISO 13006 74 IS 15658:2006 DRAFT STANDARDS COMPLETED WIDE CIRCULATION 1. DOC. CED 5(7888) Pressed ceramic tiles - Specification (First Revision of IS 15622) * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 24 No. of Amd. 2 CED 6 STONES SCOPE - STANDARDIZATION IN THE FIELD OF STONES FOR CONSTRUCTION Sl No. IS Number/ DOC Number Title Reaffirm Date STANDARDS PUBLISHED 1 IS 1121(Part 1):2013 Methods of test for determination of strength properties of natural building stones: Part 1 Compressive strength (second revision) 2 IS 1121(Part 2):2013 Methods of test for determination of strength properties of natural building stones: Part 2 Transverse strength (second revision) 3 IS 1121(Part 3):2012 Methods of test for determination of strength properties of natural building stones: Part 3 Tensile strength (second revision) 4 IS 1121(Part 4):2013 Methods of test for determination of strength properties of natural building stones: Part 4 Shear strength (second revision) 5 IS 1122:1974 Method of test for determination of true specific gravity of natural building stones (first revision) Jan 2013 6 IS 1123:1975 Method of identification of natural building stones (first revision) Jan 2013 7 IS 1124:1974 Method of test for determination of water absorption, apparent specific gravity and porosity of natural building stones (first revision) Jan 2013 8 IS 1125:2013 Method of test for determination of weathering of natural building stones (second revision) 9 IS 1126:2013 Method of test for determination of durability of natural building stones (second revision) 10 IS 1127:1970 Recommendations for dimensions and workmanship of natural building stones for masonry work (first revision) Jan 2013 11 IS 1128:1974 Specification for limestone (slab and tiles) (first revision) Jan 2013 12 IS 1129:1972 Recommendation for dressing of natural building stones (first revision) Jan 2013 13 IS 1130:1969 Specification for marble (blocks, slabs and tiles) Jan 2013 14 IS 1706:1972 Method for determination of resistance to wear by abrasion of natural building stones (first revision) Jan 2013 15 IS 1805:1973 Glossary of terms relating to stones, quarrying and dressing (first revision) Jan 2013 16 IS 3316:1974 Specification for structural granite (first revision) Jan 2013 17 IS 3620:1979 Specification for laterite stone block for masonry (first revision) Jan 2013 18 IS 3622:1977 Specification for sandstone (slabs and tiles)(first revision) Jan 2013 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 25 No. of Amd. Sl No. IS Number/ DOC Number Title Reaffirm Date 19 IS 4121:1967 Method of test for determination of water transmission rate by capillary action through natural building stones Jan 2013 20 IS 4122:1967 Method of test for surface softening of natural building stones by exposure to acidic atmospheres Jan 2013 21 IS 4348:1973 Methods of test for determination of permeability of natural building stones (first revision) Jan 2013 22 IS 5218:1969 Method of test for toughness of natural building stones Jan 2013 23 IS 5640:1970 Method of test for determining aggregate impact value of soft coarse aggregates Jan 2013 24 IS 6241:1971 Method of test for determination of stripping value of road aggregates Jan 2013 25 IS 6250:1981 Specification for roofing slate tiles (first revision) Jan 2013 26 IS 6579:1981 Specification for coarse aggregate for water bound macadam (first revision) Jan 2013 27 IS 7779(Part 1/Sec 1):1975 Schedule for properties and availability of stones for construction purpose: Part 1 Gujarat state Section 1 Availability of Stones Jan 2013 28 IS 7779(Part 1/Sec 2):1975 Schedule for properties and availability of stones for construction purposes: Part 1 Gujarat state: Section 2 Engineering properties of building stones Jan 2013 29 IS 7779(Part 1/Sec 3):1975 Schedule for properties and availability of stones for construction purposes: Part 1 Gujarat state: Section 3 Engineering properties of stone aggregates Jan 2013 30 IS 7779(Part 2/Sec 1):1979 Schedule for properties and availability of stones for construction purposes: Part 2 Maharashtra state Section 1 Availability of Stones Jan 2013 31 IS 7779(Part 2/Sec 2):1979 Schedule for properties and availability of stones for construction purposes: Part 2 Maharashtra state Section 2 Engineering properties of building stones Jan 2013 32 IS 7779(Part 2/Sec 3):1979 Schedule for properties and availability of stones for construction purposes: Part 2 Maharashtra state: Section 3 Engineering properties of stone aggregates Jan 2013 33 IS 7779(Part 3/Sec 2):1980 Schedule for properties and availability of stones for construction purposes Part 3 Tamilnadu state Section 2 Engineering properties of building stone Jan 2013 34 IS 7779(Part 3/Sec 3):1980 Schedule for properties and availability of stones for construction purposes: Part 3 Tamilnadu State section 3 Engineering properties of stone aggregates Jan 2013 35 IS 7779(Part 4/Sec 1):1996 Schedule of properties and availability of stones for construction purposes Part 4 Karnataka states Sections (1 to 3) Jan 2013 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 26 No. of Amd. 1 Sl No. IS Number/ DOC Number Title Reaffirm Date 36 IS 7779(Part 5/Sec 1):1997 Schedule of properties and availability of stones for construction purposes Part 5 Andhra Pradesh Section 1 Availability of Stones Jan 2012 37 IS 7779(Part 5/Sec 2):1997 Schedule of properties and availability of stones for construction purposes Part 5 Andhra Pradesh Section 2 Engineering properties of building stones Jan 2012 38 IS 7779(Part 5/Sec 3):1997 Schedule of properties and availability of stones for construction purposes Part 5 Andhra Pradesh Section 3 Engineering properties of stone aggregates Jan 2012 39 IS 8348:1977 Code of practice for stacking and packing of stone slabs for transportation Jan 2013 40 IS 8381:1977 Recommended practice for quarrying stones for construction purposes Jan 2013 41 IS 8759:1977 Code of practice for maintenance and preservation of stones in building Jan 2013 42 IS 9394:1979 Specification for stone lintels Jan 2013 43 IS 14223(Part 1):1995 Specification for polished building stones: Part 1 Granite Jan 2012 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 27 No. of Amd. CED 7 STRUCTURAL ENGINEERING AND STRUCTURAL SECTIONS SCOPE - STANDARDIZATION IN THE FIELD OF STRUCTURAL ENGINEERING USING STEEL/ALUMINIUM STRUCTURAL SECTIONS INCLUDING PIPELINES FOR GAS AND FORMULATION OF INDIAN STANDARDS ON DIMENSIONS/TOLERANCES OF VARIOUS HOT ROLLED/COLD FORMED SECTIONS, BARS AND FLAT PRODUCTS IN STEEL AND ALUMINIUM FOR STRUCTURAL AND GENERAL ENGINEERING APPLICATIONS LIAISION: ISO/TC 98 (O) BASES FOR DESIGN OF STRUCTURES ISO/TC 167 (O) STEEL AND ALUMINIUM STRUCTURES ISO/TC 167/SC 1 (O) ISO/TC 167/SC 3 (O) LIASON: ISO/TC 17/SC 3 (P) STEELS FOR STRUCTURAL PURPOSES Sl No. IS Number/ DOC Number Title Reaffirm Date No. of Amd. STANDARDS PUBLISHED 1 IS 800:2007 Code of practice for general construction in steel (third revision) Dec 2012 1 2 IS 801:1975 Code of practice for use of cold formed light gauge steel structural members in general building construction (first revision) Dec 2010 1 3 IS 802(Part 1/Sec 1):1995 Code of practice for use of structural steel in overhead transmission line towers, Part 1 Materials, Loads and permissible stresses Section 1 Materials and Loads (third revision) Feb 2011 4 IS 802(Part 1/Sec 2):1992 Code of practice for use of structural steel in overhead transmission line towers Part 1 : Material, loads and permissible stress Section 2 Permissible stress (third revision) Feb 2013 1 5 IS 802(Part 2):1978 Code of practice for use of structural steel in overhead transmission line towers: Part 2 Fabrication, galvanizing, inspection and packing Feb 2013 1 6 IS 802(Part 3):1978 Code of practice for use of structural steel in overhead transmission line towers: Part 3 Testing Feb 2013 7 IS 803:1976 Code of practice for design, fabrication and erection of vertical mild steel cylindrical welded oil storage tanks (first revision) Feb 2013 1 8 IS 804:1967 Specification for rectangular pressed steel tanks (first revision) Feb 2013 2 9 IS 805:1968 Code of practice for use of steel in gravity water tanks Feb 2013 10 IS 806:1968 Code of practice for use of steel tubes in general building construction (first revision) Feb 2013 1 11 IS 808:1989 Dimensions for hot rolled steel beam, column, channel and angle sections (third Revision) Oct 2009 1 12 IS 811:1987 Specification for cold formed light gauge structural steel sections (second revision) Oct 2009 1 13 IS 1173:1978 Specification for hot rolled slit steel tee bars (second revision) Oct 2009 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 28 Sl No. IS Number/ DOC Number Title Reaffirm Date 14 IS 1252:1991 Dimensions of hot rolled steel bulb angles (first revision) Feb 2013 15 IS 1730:1989 Dimensions for steel plates, sheets, strips and flats for general engineering purposes (second revision) Oct 2009 16 IS 1732:1989 Dimensions for round and square steel bars for structural and general engineering purposes (second revision) Oct 2009 17 IS 1852:1985 Rolling and cutting tolerances for hot rolled steel products (fourth revision) Feb 2013 18 IS 1863:1979 | ISO 657-19 Specification for hot rolled steel bulb flats (first revision) Oct 2009 19 IS 1864:1979 | ISO 657-18 Specification for hot-rolled steel L-sections for ship building (first revision) Oct 2009 20 IS 2314:1986 Specification for steel sheet piling sections (first revision) Feb 2013 21 IS 2713(Part 1-3):1980 Specification for tubular steel poles for overhead power lines (second revision) Feb 2013 1 22 IS 2750:1964 Specification for steel scaffoldings Dec 2010 3 23 IS 3443:1980 Specification for crane rail sections (first revision) Oct 2009 1 24 IS 3908:1986 Specification for aluminium equal leg angles (first revision) Feb 2013 25 IS 3909:1986 Specification for aluminium unequal leg angles (first revision) Feb 2013 26 IS 3921:1985 Specification for aluminium channels (first revision) Dec 2010 27 IS 3954:1991 Hot-rolled steel channel sections for general engineering purposes - Dimensions (first revision) Dec 2010 28 IS 3964:1980 Specification for light rails (first revision) Dec 2010 29 IS 4000:1992 Code of practice for high strength bolts in steel structures (first revision) Feb 2013 30 IS 4014(Part 1):1967 Code of practice for steel tubular scaffolding Part 1 Definitions and materials Dec 2010 31 IS 5384:1985 Specification for aluminium I-beam (first revision) Dec 2010 32 IS 5488:1987 Dimensions and dimensional tolerances for hot rolled steel plates for ship's hull structure(first revision) Oct 2009 33 IS 6445:1985 Specification for aluminium tee-sections (first revision) Dec 2010 34 IS 6449:1987 Specification for aluminium bulb angles for marine application (first revision) Oct 2009 35 IS 6475:1987 Specification for aluminium tee bars for marine application (first revision) Oct 2009 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 29 No. of Amd. 2 1 Sl No. IS Number/ DOC Number Title Reaffirm Date 36 IS 6476:1987 Specification for aluminium bulb plates for marine application (first revision) Oct 2009 37 IS 6533(Part 1):1989 Code of practice for design and construction of steel chimneys Part 1 Mechanical aspects (first revision) Dec 2010 1 38 IS 6533(Part 2):1989 Code of practice for design and construction of steel chimneys Part 2 Structural aspects (first revision) Feb 2013 1 39 IS 7205:1974 Safety code for erection of structural steel work Dec 2010 40 IS 7215:1974 Tolerances for fabrication of steel structures Dec 2010 41 IS 7452:1990 Specification for hot-rolled steel sections for doors, windows and ventilators(second revision) Feb 2013 42 IS 8081:1976 Specification for slotted sections Dec 2010 43 IS 8147:1976 Code of practice for use of aluminium alloys in structures Dec 2010 44 IS 8640:1977 Recommendations for dimensional parameters for industrial building Dec 2010 45 IS 9178(Part 1):1979 Criteria for design of steel bins for storage of bulk materials Part 1 General requirements and assessment of loads Dec 2010 46 IS 9178(Part 2):1979 Criteria for design of steel bins for storage of bulk material Part 2 Design criteria Dec 2010 47 IS 9178(Part 3):1980 Criteria for design of steel bins for storage of bulk materials Part 3 Bins designed for mass flow and funnel flow Dec 2010 48 IS 9964(Part 1):1981 Recommendations for maintenance and operation of petroleum storage tanks Part 1 Preparation of tanks for safe Dec 2010 49 IS 9964(Part 2):1981 Recommendations for maintenance and operation of petroleum storage tanks Part 2 Inspection Dec 2010 50 IS 10182(Part 1):1982 Dimensions and tolerances for hot-rolled track shoe sections Part 1 Section TS-L1 Dec 2010 51 IS 10182(Part 2):1985 Dimensions and tolerances for hot-rolled track shoe sections Part 2 Section TS-H1 Dec 2010 52 IS 10987:1992 Code of practice for design, fabrication, testing and installation of underground/above ground horizontal cylindrical storage tanks for petroleum products (first revision) Feb 2013 53 IS 12778:2004 Hot rolled parallel flange steel sections for beam, columns and bearing pile - Dimensions and section properties (first revision) Oct 2009 54 IS 12779:1989 Rolling and cutting tolerances for hot rolled parallel flange beam and column sections Oct 2009 55 IS 12843:1989 Tolerances for erection of steel structures Dec 2010 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 30 No. of Amd. 1 1 2 1 Sl No. IS Number/ DOC Number Title Reaffirm Date 56 IS 15663(Part 1):2006 Code of practice for design and installation of natural gas pipelines: Part 1 Laying of pipelines Jul 2011 57 IS 15663(Part 2):2006 Code of practice for design and installation of natural gas pipelines: Part 2 Laying of pipelines in crossings Jul 2011 58 IS 15663(Part 3):2006 Code of practice for design and installation of natural gas pipelines: Part 3 Pre-commissioning and commissioning of pipelines Jul 2011 59 SP 6(Part 4): 1969 Handbook for structural engineers use of high strength friction grip bolts 60 SP 6(Part 5): 1980 Handbook for structural engineers - Cold-formed, light gauge steel structures (first revision) 61 SP 6(Part 6): 1972 Handbook for structural engineers - Application of plastic theory in design of steel structures DRAFT STANDARDS UNDER PRINT 1 DOC.CED 7(7836) Draft Amendment No. 2 to IS 808:1989 2 DOC.CED 7(7850) Draft Indian Standard on Use of Structural Steel in Overhead Transmission Line Towers - Code of Practice: Part 1 Materials, Loads and Design Strengths: Section 1 Materials and Loads [Fifth Revision of IS 802(Part 1/Sec 1)] 3 DOC.CED 7(7851) Draft Indian Standard on Use of Structural Steel in Overhead Transmission Line Towers - Code of Practice: Part 1 Materials, Loads and Design Strengths: Section 2 Design Strengths [Fourth Revision of IS 802(Part 1/Sec 2)] * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 31 No. of Amd. 1 CED 9 TIMBER AND TIMBER STORES SCOPE - TIMBERS; STANDARD NAMES OF INDIAN TIMBERS; CLASSIFICATION OF COMMERCIAL TIMBERS AND THEIR ZONAL DISTRIBUTION; CHARACTERISTICS OF IMPORTED AND PLANTATION TIMBERS; TIMBER, SIZING DEFECTS OF; TIMBER FOR AIR CRAFT; TIMBER FOR MARINE PURPOSES; SEASONING AND TREATMENT OF TIMBER; LOGS FOR PLYWOOD; GLOSSARY OF TECHNICAL TERMS USED IN TIMBER TECHNOLOGY; STANDARD DIMENSIONS FOR WOOD POLES OF INDIAN SPECIES FOR VARIOUS BREAKING LOADS; MOISTURE CONTENT AND SPECIFICATION OF TIMBER FOR VARIOUS USES; METHODS OF TESTING TIMBER; GRADING OF WOOD; JOINERY; METHOD OF TEST FOR THE TOXICITY OF WOOD PRESERVATIVES TO MICROORGANISMS AND INSECTS, TIMBER IN BUILDING CONSTRUCTION, FLOORS; GRADING OF TIMBER, SIZES OF GRADED TIMBER STANDARDIZATION IN THE FIELD OF TIMBER STORES INCLUDING BAMBOO AND CANE STORES SUCH AS WOODEN HANDLES, WOODEN CONTAINERS INCLUDING PLYWOOD TEA-CHESTS, CANE BASKETS, BAMBOO TENT POLES ETC; AND ANY OTHER WOODENWARE ITEMS NOT COVERED BY OTHER SECTIONAL COMMITTEE AND TO ADVISE THE LATER COMMITTEES WHEREVER CALLED UPON TO DO SO LIAISON: ISO/TC 218 (O) TIMBER Sl No. IS Number/ DOC Number Title Reaffirm Date No. of Amd. STANDARDS PUBLISHED 1 IS 10(Part 1):1990 Specification for plywood tea-chests: Part 1 General (fifth revision) 2 IS 10(Part 2):2013 Specification for plywood tea-chests: Part 2 Plywood (sixth revision) 3 IS 10(Part 3):1974 Specification for plywood tea-chests: Part 3 Battens (fourth revision) May 2010 3 4 IS 10(Part 4):1989 Specification for plywood tea-chests: Part 4 Metal fittings (fifth revision) Dec 2012 1 5 IS 10(Part 5):1976 Specification for plywood tea-chests; Part 5 Assembly and packing (fourth revision) May 2010 6 IS 190:1991 Coniferous sawn timber (Baulks and scantlings) - Specification (fourth revision) May 2010 7 IS 287:1993 Permissible moisture content for timber used for different purposes - Recommendations (third revision) Dec 2012 8 ** IS 399:1963 Classification of commercial timbers and their zonal distribution (first revision ) May 2010 9 IS 401:2001 Preservation of timber - Code of practice (fourth revision) Dec 2011 10 IS 620:1985 Specification for wooden tool handles general requirements (fourth revision) May 2010 11 IS 656:1988 Specification for logs for plywood (third revision) Dec 2012 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS May 2010 ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 32 1 1 Sl No. IS Number/ DOC Number Title Reaffirm Date 12 IS 707:2011 Glossary of terms applicable to timber technology and utilization( third revision) 13 IS 876:1992 Wood poles for overhead power and telecommunication lines Specification (third revision) Dec 2012 14 IS 1140:1988 Specification for logs for matches (second revision) Dec 2012 15 IS 1141:1993 Seasoning of timber - Code of practice (second revision) Aug 2009 16 ** IS 1150:2000 Trade names and abbreviated symbols for timber species (third revision) May 2010 17 IS 1326:1992 Non-coniferous sawn timber (Baulks and scantlings) Specification (second revision) Dec 2012 18 IS 1331:1971 Specification for cut sizes of timber (second revision) (Superseding IS 1629:1960) Dec 2011 19 IS 1503:1988 Specification for wooden packing cases (third revision) Dec 2012 20 IS 1707:1979 Specification for wood wool for general packaging purposes (first revision) Dec 2012 21 IS 1708(Part 1):1986 Methods of testing of small specimens of timber: Part 1 Determination of moisture content (second revision) May 2010 2 22 IS 1708(Part 2):1986 Methods of testing of small specimens of timber: Part 2 Determination of specific gravity (second revision) May 2010 2 23 IS 1708(Part 3):1986 Methods of testing of small specimens of timber: Part 3 Determination of volumetric shrinkage (second revision) May 2010 2 24 IS 1708(Part 4):1986 Methods of testing of small specimens of timber: Part 4 Determination of radial and tangential shrinkage and fibre saturation point (second revision) May 2010 2 25 IS 1708(Part 5):1986 Methods of testing of small specimens of timber: Part 5 Determination of static bending strength (second revision) May 2010 2 26 IS 1708(Part 6):1986 Methods of testing of small specimens of timber: Part 6 Determination of static bending strength under two point loading (second revision) May 2010 2 27 IS 1708(Part 7):1986 Methods of testing of small specimens of timber: Part 7 Determination of impact bending strength (second revision) May 2010 2 28 IS 1708(Part 8):1986 Methods of testing of small specimens of timber: Part 8 Determination of compressive strength parallel to grain (second revision) May 2010 2 29 IS 1708(Part 9):1986 Methods of testing of small specimens of timber: Part 9 Determination of compressive strength perpendicular to grain (second revision) May 2010 2 30 IS 1708(Part 10):1986 Methods of testing of small specimens of timber: Part 10 Determination of hardness under static indentation (second revision) May 2010 2 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 33 No. of Amd. 2 Sl No. IS Number/ DOC Number Title Reaffirm Date 31 IS 1708(Part 11):1986 Methods of testing of small specimens of timber: Part 11 Determination of shear strength parallel to grain (second revision) May 2010 2 32 IS 1708(Part 12):1986 Methods of testing of small specimens of timber: Part 12 Determination of tensile strength parallel to grain (second revision) May 2010 2 33 IS 1708(Part 13):1986 Methods of testing of small specimens of timber: Part 13 Determination of tensile strength perpendicular to grain (second revision) May 2010 2 34 IS 1708(Part 14):1986 Methods of testing of small specimens of timber: Part 14 Determination of cleavage strength parallel to grain (second revision) May 2010 2 35 IS 1708(Part 15):1986 Methods of testing of small specimens of timber: Part 15 Determination of nail and screw holding power (second revision) May 2010 2 36 IS 1708(Part 16):1986 Methods of testing of small specimens of timber: Part 16 Determination of brittleness by Izod impact (second revision) May 2010 2 37 IS 1708(Part 17):1986 Methods of testing of small specimens of timber: Part 17 Determination of brittleness by Charpy impact (second revision) May 2010 2 38 IS 1708(Part 18):1986 Methods of testing of small specimens of timber: Part 18 Determination of torsional strength (second revision) May 2010 2 39 IS 1898:1990 Timber for aircraft construction in converted form (finished form) - Specification (second revision) May 2010 1 40 IS 1900:1974 Methods of tests for wood poles (first revision) Dec 2012 41 IS 1902:2006 Preservation of bamboo and cane for non-structural purposes Code of practice (second revision) May 2011 42 IS 2133:1983 Specification for wooden tent pins (second revision) May 2010 43 IS 2179:1979 Specification for converted timber for lorry bodies (first revision) May 2010 44 IS 2203:1993 Wooden cross arms - Specification (second revision) Dec 2012 45 ** IS 2372:2004 Timber for cooling towers - Specification (second revision) Aug 2009 46 IS 2377:1967 Tables for volumes of cut sizes of timber (first revision) Dec 2012 47 IS 2408:1963 Methods of static tests of timber in structural sizes May 2010 48 IS 2455:1990 Method of sampling of model trees and logs and their conversion for timber testing (second revision) May 2010 49 IS 2674:1988 Specification for battened plywood cases (second revision) Dec 2012 50 IS 2683:1980 Guide for installation of impregnation plants for timber (second revision) May 2010 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 34 No. of Amd. 1 1 Sl No. IS Number/ DOC Number Title Reaffirm Date 51 IS 2753(Part 1):1991 Methods for estimation of preservatives in treated timber and in treating solutions: Part 1 Determination of copper, arsenic, chromium, zinc, boron, creosote and fuel oil (first revision) 52 IS 2753(Part 2):2014 Methods for estimation of preservatives in treated timber and No. of Amd. May 2010 1 in treating solutions : Part 2 Determination of copper in्copper organic preservative salt (second revision) 53 IS 2891:1975 Specification for wooden handles for felling axes and hand axes (first revision) Dec 2011 54 IS 2892:1993 Wooden handles for picks and beaters - Specification (second revision) Dec 2012 55 IS 2893:1992 Wooden handles for adzes - Specification (second revision) Dec 2011 56 IS 2894:1987 Specification for wooden handles for wood working chisels and gouges (first revision) Dec 2011 57 IS 2895:1990 Dec 2011 58 IS 2896:1978 Wooden handles for rasps, engineers' file and engineers' scrapers - Specification (second revision) Specification for wooden handles for carpenters' augers (first revision) 59 IS 2897:1983 Specification for wooden handles for shovels (first revision) May 2010 60 IS 2922:1975 Specification for wooden tent mallets (first revision) Dec 2011 61 IS 3053:1977 Specification for cane baskets for general purposes (first revision) May 2010 62 IS 3071:1981 Specification for wooden crates (first revision) Dec 2011 63 IS 3084:1989 Pencil slats - Specification (second revision) Dec 2012 64 IS 3337:1978 Specification for ballies for general purposes (first revision) Dec 2011 1 65 IS 3364(Part 1):1976 Methods of measurement and evaluation of defects in timber: Part 1 Logs (first revision) Aug 2009 1 66 IS 3364(Part 2):1976 Methods of measurement and evaluation of defects in timber: Part 2 Converted timber (first revision) Aug 2009 1 67 IS 3386:1979 Specification for wooden fence posts (first revision) Dec 2011 1 68 IS 3728:1985 Specification for wooden boxes for packaging of apples (first revision) May 2010 69 IS 3731:1985 Specification for teak squares (first revision) May 2010 70 IS 3806:1966 Specification for wooden beaters May 2010 71 IS 4422:1985 Specification for willow clefts for cricket bats (first revision) May 2010 72 IS 4423:1999 Hand-sawing of timber - Guide (first revision) Aug 2009 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS Dec 2011 ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 35 1 1 Sl No. IS Number/ DOC Number Title Reaffirm Date 73 IS 4424:1967 Specification for timber for use in coal mines May 2010 1 74 IS 4650:1968 Specification for wooden anvil blocks May 2010 2 75 IS 4833:1993 Methods for field testing of preservatives in wood (first revision) Dec 2012 76 IS 4873(Part 1):2008 Method of laboratory testing of wood preservatives against fungi and borers (powder post beetles) : Part 1 Determination of threshold values of wood preservatives against fungi (second revision) Mar 2014 77 IS 4873(Part 2):2008 Method of laboratory testing of wood preservatives against fungi and borers (powder post beetles): Part 2 Determination of threshold values of wood preservatives against borers (powder post beetles) (second revision) Mar 2014 78 IS 4895:1985 Specification for teak logs (first revision) May 2010 79 IS 4907:2004 Method of testing timber connector joints (first revision) Aug 2009 80 IS 4953:1989 Wooden handles for hand hammers - Specification (second revision) Dec 2012 81 IS 4970:1973 Key for identification of commercial timbers (first revision) May 2010 82 IS 5246:2000 Coniferous logs - Specification (first revision) Dec 2012 83 IS 5247(Part 1):1982 Specification for converted timber (coniferous) : Part 1 Light furniture (first revision) May 2010 84 IS 5247(Part 2):1982 May 2010 85 IS 5806:1970 Specification for converted timber (coniferous) : Part 2 Packing cases and crates (first revision) Specification for non-coniferous timber in converted form for ammunition/explosives boxes 86 IS 5942:1989 Wooden handles for POWRAHS - Specification (first revision) Dec 2012 87 IS 5966:1993 Non-coniferous timber in converted form for general purposes Specification (first revision) Dec 2012 1 88 IS 5978:1970 Code of practice for design of wood poles for overhead power and telecommunication lines May 2010 2 89 IS 6056:1970 Specification for jointed wood poles for overhead power and telecommunication lines May 2010 1 90 IS 6341:1971 Method for laboratory test for efficacy of wood preservatives against soft rot Dec 2011 91 IS 6346:1971 Method of tests for timber props for mines May 2010 92 IS 6497:1990 Method of test for the efficacy of preservatives and evaluating the natural durability of timbers used in cooling towers (first revision) May 2010 93 IS 6534:1971 Guiding principles for grading and inspection of timber May 2010 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS May 2010 ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 36 No. of Amd. 2 Sl No. IS Number/ DOC Number Title Reaffirm Date 94 IS 6641:1985 Specification for wooden disc for tents (first revision) May 2010 95 IS 6642:1986 Specification for mason's mallets (first revision) May 2010 96 IS 6643:1987 Specification for wooden pins for bivouac tents (first revision) Dec 2011 97 IS 6644:1986 Specification for tinman's mallets (first revision) May 2010 98 IS 6656:1986 Specification for caulking mallets (first revision) May 2010 99 IS 6662:1993 Timber species suitable for wooden packaging - Specification (second revision) Dec 2012 100 IS 6676:1986 Specification for bossing (plumbers), mallets (first revision) May 2010 101 IS 6703:1972 Glossary of wooden packaging terms Dec 2011 102 IS 6707:1972 Specification for willow logs for artificial limbs May 2010 103 IS 6711:1972 Code of practice for maintenance of wood poles for overhead power and telecommunication lines May 2010 104 IS 6729:1972 Specification for wooden paddles May 2010 105 IS 6791:1973 Method of testing natural durability of timber and efficacy of the wood preservatives against marine borers May 2010 106 IS 6874:2008 Method of test for bamboos (first revision) Mar 2014 107 IS 7308:1999 Non-coniferous logs - Specification (first revision) Aug 2009 108 IS 7315:1974 Guidelines for design, installation and testing of timber seasoning kilns (Compartment type with cross-forced air) May 2010 109 IS 7344:1974 Specification for bamboo tent poles May 2010 110 IS 7548:1992 Vase for store tent - Specification (first revision) Dec 2011 111 IS 7549:1975 Specification for timber half wrought for sporting rifles May 2010 112 IS 7698:1983 Specification for returnable wooden crates for vegetables ( first revision) Dec 2012 113 IS 7850:1975 Specification for wooden box for microscope slides May 2010 114 IS 7992:1983 Specification for plywood cases for packing tobacco for export (first revision) Dec 2012 115 IS 8001:1976 Specification for packaging of plywood, blockboards and flush doors for export Dec 2011 116 IS 8242:1976 Methods of tests for split bamboos Aug 2009 117 IS 8292:1992 Evaluation of working quality of timber under different wood working operations - Method of test (first revision) Dec 2011 118 IS 8295(Part 1):1976 Specification for bamboo chicks: Part 1 Fine Dec 2012 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 37 No. of Amd. 1 1 2 1 1 Sl No. IS Number/ DOC Number Title Reaffirm Date 119 IS 8295(Part 2):1976 Specification for bamboo chicks: Part 2 Coarse Dec 2012 120 IS 8720:1978 Methods of sampling of timber scantlings from depots and their conversion for testing Dec 2011 121 IS 8725:1978 Specification for wirebound wooden boxes Dec 2012 122 IS 8726:1978 Specification for wirebound wooden crates Dec 2012 123 IS 8745:1994 Methods of presentation of data of physical and mechanical properties of timber (first revision) Dec 2012 124 IS 9096:2006 Preservation of bamboo for structural purposes - Code of practice (first revision) May 2011 125 IS 9104:1979 Guide for storage and protection of logs and sawn timber May 2010 126 IS 9561:1985 Code of practice for felling and conversion of trees into logs (first revision) May 2010 127 IS 9576:1980 Guide for mill sawing of timber May 2010 128 IS 9590:1980 Specification for non-returnable wooden boxes for horticulture produce Dec 2011 129 IS 10013(Part 1):1981 Specification for water soluble type wood preservatives: Part 1 Acid-copper-chrome (ACC) preservative Aug 2009 130 IS 10013(Part 2):1981 Specification for water soluble type wood preservatives: Part 2 Copper-chrome-arsenic (CCA) wood preservative Aug 2009 131 IS 10013(Part 3):1981 Specification for water soluble type wood preservatives: Part 3 Copper-chrome-boron (CCB) wood preservative Aug 2009 132 IS 10145:1982 Specification for bamboo supports for camouflaging equipment May 2010 1 133 IS 10394:1982 Specification for wooden sleepers for railway track May 2010 1 134 IS 10402:1982 Specification for pin-needle hardboard boxes for packaging of apples May 2010 1 135 IS 10420:1982 Method of determination of sound absorption coefficient of timber by standing wave method Aug 2009 136 IS 10499:1983 Specification for wooden toggles May 2010 137 IS 10687:1983 Guidelines for nailing of large framed wooden containers Dec 2012 138 IS 10753:1983 Code of practice for preservation of wooden sleepers for railway track by pressure treatment Aug 2009 139 IS 10754:1983 Method of determination of thermal conductivity of timber Aug 2009 140 IS 11100:1984 Specification for sweeping brooms May 2010 141 IS 11106:1984 Specification for carpenter's mallets May 2010 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 38 No. of Amd. 1 1 Sl No. IS Number/ DOC Number Title Reaffirm Date 142 IS 11131:1984 Specification for wooden casks and barrels Dec 2012 143 IS 11215:1991 Moisture content of timber and timber products - Methods for determination (first revision) May 2010 144 IS 11288:1985 Recommendations for off road transportation of timber May 2010 145 IS 12896:1990 Indian timbers for door and window shutters and frames Classification May 2010 146 IS 13621:1993 Determination of dielectric constant of wood under microwave frequencies - Method of test Dec 2012 147 IS 13622:1993 Indian timbers for furnitures and cabinets - Classification Dec 2012 148 IS 14960:2001 Preservative treated and seasoned sawn timber from rubber wood (Hevea Brasiliensis) - Specification Mar 2014 149 IS 15455:2004 Grading rules for split canes Aug 2009 150 IS 15456:2004 Grading rules for unsplit canes Aug 2009 151 IS 15457:2004 Logs for production of sliced veneers - Specification (Superseding IS 5248:1988, IS 6342:1987, & IS 13240:1991) Aug 2009 152 IS 15458:2004 Classification of Indian canes and their zonal distribution Aug 2009 153 IS 15890:2010 Design, installation and testing of solar timber seasoning kilnGuidelines 154 SP 33(S&T): 1986 Handbook on timber engineering FINALISED DRAFTS UNDER PRINT 1 DOC.CED 9(7734) Draft Amendment No. 2 to IS 8001:1976 Specification for packaging of plywood, blockboards and flush doors for export 2 DOC.CED 9(7649) Draft Amendment No. 1 to IS 2372:2004 Timber for cooling towers - Specification (second revision) DRAFT STANDARDS ISSUED IN WIDE CIRCULATION 1 DOC.CED 9(7876) Draft Amendment No. 1 to IS 707:2011 2 DOC.CED 9(7893) Draft Amendment No. 1 to IS 401:2001 3 DOC.CED 9(7897) Draft Amendment No. 1 to IS 9096:2006 4 DOC.CED 9(7901) Draft Amendment No. 3 to IS 1140:1988 5 DOC.CED 9(7902) Draft Amendment No. 1 to IS 4873 (Part 1):2008 6 DOC.CED 9(7904) Draft Amendment No. 1 to IS 1150:2000 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 39 No. of Amd. 1 CED 11 DOORS, WINDOWS AND SHUTTERS SCOPE - STANDARDIZATION IN THE FIELD OF DOORS, WINDOWS, VENTILATORS, GATES AND SHUTTERS MADE OF ANY MATERIAL LIAISON: ISO/TC 162 (O) DOORS AND WINDOWS Sl No. IS Number/ DOC Number Title Reaffirm Date No. of Amd. STANDARDS PUBLISHED 1 IS 1003(Part 1):2003 Timber panelled and glazed shutters: Part 1 Door Shutters Specification (fourth revision) Aug 2013 2 2 IS 1003(Part 2):1994 Specification for timber panelled and glazed shutters: Part 2 Window and ventilator shutters (third revision) Nov 2011 3 3 IS 1038:1983 Specification for steel doors, windows and ventilators (third revision) Nov 2011 3 4 IS 1081:1960 Code of practice for fixing and glazing of metal (steel and aluminium) doors, windows and ventilators Nov 2011 1 5 IS 1361:1978 Specification for steel windows for industrial buildings (first revision) Nov 2011 2 6 IS 1948:1961 Specification for aluminium doors, windows and ventilators Nov 2011 1 7 IS 1949:1961 Specification for aluminium windows for industrial buildings Nov 2011 1 8 IS 2191(Part 1):1983 Specification for wooden flush door shutters (cellular and hollow core type): Part 1 Plywood face panels (fourth revision) Nov 2011 2 9 IS 2191(Part 2):1983 Specification for wooden flush door shutters (cellular and hollow core type): Part 2 Particle board and hardboard face panels (third revision) Nov 2011 2 10 IS 2202(Part 1):1999 Specification for wooden flush door shutters (solid core type): Part 1 Plywood face panels (sixth revision) Jul 2011 3 11 IS 2202(Part 2):1983 Specification for wooden flush door shutters (solid core type): Part 2 Particle board and hardboard face panels (third revision) Nov 2011 2 12 IS 4020(Part 1):1998 Door shutters - Methods of tests: Part 1 General (third revision) Aug 2013 1 Part 2 Measurement of dimensions and squareness (third revision) Aug 2013 1 13 IS 4020(Part 2):1998 14 IS 4020(Part 3):1998 Part 3 Measurement of general flatness (third revision) Aug 2013 1 15 IS 4020(Part 4):1998 Part 4 Local planeness test (third revision) Aug 2013 1 16 IS 4020(Part 5):1998 Part 5 Impact indentation test (third revision) Aug 2013 17 IS 4020(Part 6):1998 Part 6 Flexure test (third revision) Aug 2013 18 IS 4020(Part 7):1998 Part 7 Edge loading test (third revision) Aug 2013 1 19 IS 4020(Part 8):1998 Part 8 Shock resistance test (third revision) Aug 2013 2 20 IS 4020(Part 9):1998 Part 9 Buckling resistance test (third revision) Aug 2013 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 40 Sl No. IS Number/ DOC Number Title Reaffirm Date 21 IS 4020(Part 10):1998 Part 10 Slamming test (third revision) Aug 2013 22 IS 4020(Part 11):1998 Part 11 Misuse test (third revision) Aug 2013 23 IS 4020(Part 12):1998 Part 12 Varying humidity test (third revision) Aug 2013 24 IS 4020(Part 13):1998 Part 13 End immersion test (third revision) Aug 2013 25 IS 4020(Part 14):1998 Part 14 Knife test (third revision) Aug 2013 26 IS 4020(Part 15):1998 Part 15 Glue adhesion test (third revision) Aug 2013 27 IS 4020(Part 16):1998 Part 16 Screw withdrawal resistance test (third revision) Aug 2013 28 IS 4021:1995 Timber door, window and ventilator frames - Specification (third revision) 29 IS 4043:1969 Recommendations for symbolic designations of direction of closing and faces of doors, windows and shutters Nov 2011 30 IS 4351:2003 Steel door frames - Specification (second revision) Aug 2013 31 IS 4913:1968 Code of practice for selection, installation and maintenance of timber doors and windows Nov 2011 32 IS 6198:1992 Specification for ledged, braced and battened timber door shutters (second revision) Nov 2011 33 ** IS 6248:1979 Specification for metal rolling shutters and rolling grills (first revision) Nov 2011 34 IS 10428:1983 / ISO 1804:1972 Glossary of terms relating to doors Nov 2011 35 IS 10451:1983 Specification for steel sliding shutters (top hung type) Nov 2011 1 36 IS 10521:1983 Specification for collapsible gates Nov 2011 1 37 IS 14856:2000 Glass fibre reinforced plastic (GRP) panel type door shutters for internal use - Specification 38 IS 15380:2003 Moulded raised high density fibre (HDF) panel doors - Specification 39 IS 15931:2012 Solid Panel Foam UPVC Door Shutters - Specification 40 IS 16073:2013 Bamboo - Jute Composite Panel Door Shutter - Specification 41 IS 16074:2013 Steel Flush Door Shutters - Specification 42 IS 16096:2013 Phenol Bonded Bamboo - Jute Composite Hollow Door Shutter - Specification Jul 2011 DOC.CED 11(7847) Aug 2013 Preliminary Draft of Unplasticized PVC Profile Panelled Door Shutters (including door frames) - Specification DRAFT STANDARDS FORMULATED 1 DOC.CED 11(7853) Preliminary Draft on Pressed Steel Window and Ventilator Specification * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 41 2 3 1 2 Jul 2011 DRAFT STANDARD ISSUED IN WIDE CIRCULATION 1 No. of Amd. 1 CED 12 FUNCTIONAL REQUIREMENTS IN BUILDINGS SCOPE - STANDARDIZATION IN THE FIELD OF FUNCTIONAL REQUIREMENTS IN BUILDINGS: a) FROM COMFORT POINT OF VIEW, SUCH AS SPACE DISTRIBUTION, ORIENTATION, DAY-LIGHTING, VENTILATION, ACOUSTICS AND THERMAL COMFORTS; b) FROM HEALTH AND SAFETY POINT OF VIEW; c) FROM THE POINT OF VIEW OF ACCESSIBILITY FOR PERSONS WITH DISABILITY; AND d) FROM THE POINT OF VIEW OF ENERGY REQUIREMENTS. LIAISON: ISO/TC 43/SC 2 (O) BUILDING ACOUSTICS Sl No. IS Number/ DOC Number Title Reaffirm Date No. of Amd. STANDARDS PUBLISHED 1 IS 1950:1962 Code of practice for sound insulation of non-industrial buildings Aug 2010 2 IS 2440:1975 Guide for day lighting of buildings (second revision) Oct 2013 3 IS 2526:1963 Code of practice for acoustical design of auditoriums and conference halls Aug 2010 4 IS 3103:1975 Code of practice for industrial ventilation (first revision) Oct 2013 5 IS 3362:1977 Code of practice for natural ventilation of residential buildings (first revision) Oct 2013 6 IS 3483:1965 Code of practice for noise reduction in industrial buildings Aug 2010 7 IS 3792:1978 Guide for heat insulation of non industrial buildings (first revision) Oct 2013 8 IS 4954:1968 Recommendations for noise abatement in town planning Aug 2010 9 IS 4963:1987 Recommendations for buildings and facilities for the physically handicapped (first revision) Aug 2010 10 IS 5499:1969 Code of practice for construction of underground air-raid shelters in natural soil Oct 2013 11 IS 6060:1971 Code of practice for day lighting of factory buildings Oct 2013 12 IS 6074:1971 Code of practice for functional requirements of hotels, restaurants and other food service establishments Aug 2010 13 IS 7662(Part 1):1974 Recommendations for orientation of buildings: Part 1 Nonindustrial buildings Oct 2013 14 IS 7942:1976 Code of practice for day lighting of educational buildings Oct 2013 15 IS 8827:1978 Recommendations for basic requirements of school buildings Aug 2010 16 IS 9736:1981 Glossary of terms applicable to acoustics in buildings Aug 2010 17 IS 11050(Part 1):1984 / ISO 717/1-1982 Rating of sound insulation in buildings and of building elements: Part 1 Airborne sound insulation in buildings and of interior building elements Jan 2012 18 IS 11050(Part 2):1984 / ISO 717/2-1982 Rating of sound insulation in buildings and of building elements: Part 2 Impact sound insulation Jan 2012 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 42 1 1 2 Sl No. IS Number/ DOC Number Title 19 Rating of sound insulation in buildings and of building elements: Part 3 Airborne sound insulation of facade elements Jan 2012 IS 11050(Part 3):1984 / ISO 717/3-1982 Reaffirm Date 20 IS 11907:1986 Recommendations for calculation of solar radiation on buildings Jan 2012 21 IS 12332:1988 Code of practice for ventilation in petro-chemical plants and refineries Oct 2013 22 IS 13735:1993 / ISO 8201-1987 Specification for audible emergency evacuation signal Jan 2012 23 SP 32(S&T): 1986 Handbook on functional requirements of industrial buildings (lighting and ventilation) 24 SP 41(S&T): 1987 Handbook on functional requirements of buildings (other than industrial buildings) * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 43 No. of Amd. CED 13 BUILDING CONSTRUCTION PRACTICES SCOPE - DRAWING UP OF CODES OF PRACTICE FOR BUILDING CONSTRUCTION AND MAINTENANCE LIAISON: ISO/TC 59 (O) BUILDING CONSTRUCTION ISO/TC 59/SC 2 TERMINOLOGY AND HARMONIZATION OF LANGUAGES ISO/TC 59/SC 3 FUNCTIONS/USER REQUIREMENTS AND PERFORMANCE IN BUILDING CONSTRUCTION ISO/TC 59/SC 8 JOINTING PRODUCTS ISO/TC 59/SC 13 ORGANIZATION OF INFORMATION ABOUT CONSTRUCTION WORKS ISO/TC 165 (O)TIMBER STRUCTURES ISO/TC 179/SC 1 UNREINFORCED MASONRY ISO/TC 179/SC 2 REINFORCED MASONRY ISO/TC 179/SC 3 TEST METHODS Sl No. IS Number/ DOC Number Title Reaffirm Date No. of Amd. STANDARDS PUBLISHED 1 IS 883:1994 Code of practice for design of structural timber in building (fourth revision) Sep 2009 2 IS 965:1963 Equivalent metric units for scales, dimensions and quantities in general construction work Sep 2010 3 IS 1414:1989 Code of practice for fixing of wall coverings (first revision) Sep 2009 4 IS 1477(Part 1):1971 Code of practice for painting of ferrous metals in buildings: Part 1 Pretreatment (first revision) Sep 2010 5 IS 1477(Part 2):1971 Code of practice for painting of ferrous metals in buildings: Part 2 Painting (first revision) Sep 2010 6 IS 1597(Part 1):1992 Code of practice for construction of stone masonry: Part 1 Rubble stone masonry (first revision) Dec 2011 7 IS 1597(Part 2):1992 Code of practice for construction of stone masonry: Part 2 Ashlar masonry (first revision) Dec 2011 8 IS 1634:1992 Code of practice for design and construction of wood stairs for houses (second revision) Dec 2011 9 IS 1649:1962 Code of practice for design and construction of flues and chimneys for domestic heating appliances Sep 2012 10 IS 1834:1984 Specification for hot applied sealing compound for joints in concrete (first revision) Sep 2010 11 IS 1838(Part 1):1983 Specification for preformed fillers for expansion joint in concrete pavement and structures (non extruding and resilient type): Part 1 Bitumen impregnated fibre (first revision) Sep 2010 12 IS 1838(Part 2):1984 Specification for preformed fillers for expansion joint in concrete pavement and structures (non extruding and resilient type) Part 2 CNSL Aldehyde resin and coconut pith Sep 2010 13 IS 1838(Part 3):2011 Preformed Fillers for Expansion Joints in Concrete Pavements and Structures (Non-Extruding and Resilient Type) Specification: Part 3 Polymer Based * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 44 2 1 1 Sl No. IS Number/ DOC Number Title Reaffirm Date 14 IS 1905:1987 Code of practice for structural use of unreinforced masonry (third revision) Sep 2012 15 IS 1946:1961 Code of practice for use of fixing devices in walls, ceilings and floors of solid construction Sep 2012 16 IS 2110:1980 Code of practice for in-situ construction of walls in building with soil-cement (first revision) Sep 2012 17 IS 2115:1980 Code of practice for flat roof finish: Mud phuska (second revision) Sep 2012 18 IS 2116:1980 Specification for sand for masonry mortars (first revision) Sep 2012 19 IS 2118:1980 Code of practice for construction of jack-arch type of built-up floor or roof (first revision) Sep 2012 20 IS 2119:1980 Code of practice for construction of brick-cum-concrete composite (Madras terrace) floor and roof (first revision) Sep 2012 21 IS 2204:1962 Code of practice for construction of reinforced concrete shell Sep 2010 22 IS 2212:1991 Code of practice for brick works (first revision) Sep 2009 23 IS 2250:1981 Code of practice for preparation and use of masonry mortars (first revision) Sep 2010 24 IS 2338(Part 1):1967 Code of practice for finishing of wood and wood-based materials: Part 1 Operations and workmanship Sep 2010 25 IS 2338(Part 2):1967 Code of practice for finishing of wood and wood-based materials: Part 2 Schedules Sep 2010 26 IS 2366:1983 Code of practice for nail-jointed timber construction (first revision) Sep 2010 27 IS 2395(Part 1):1994 Code of practice for painting of concrete, masonry and plaster surfaces: Part 1 Operations and workmanship (first revision) Sep 2009 28 IS 2395(Part 2):1994 Code of practice for painting of concrete, masonry and plaster surfaces: Part 2 Schedules (first revision) Sep 2009 29 IS 2441:1984 Code of practice for fixing ceiling coverings (first revision) Sep 2010 30 IS 2524(Part 1):1968 Code of practice for painting of non-ferrous metals in buildings: Part 1 Pretreatment Sep 2010 31 IS 2524(Part 2):1968 Code of practice for painting of non-ferrous metals in buildings: Part 2 Painting Sep 2010 32 IS 2527:1984 Code of practice for fixing rainwater gutters and downpipes for roof drainage (first revision) Sep 2010 33 IS 2700:1987 Code of practice for roofing with wooden shingles (first revision) Sep 2010 34 IS 2792:1964 Code of practice for design and construction of stone slab over joist floor Sep 2010 35 IS 2858:1984 Code of practice for roofing with mangalore tiles (first revision) Sep 2010 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 45 No. of Amd. 1 Sl No. IS Number/ DOC Number Title Reaffirm Date 36 IS 3140:1965 Code of practice for painting asbestos cement building products Sep 2010 37 IS 3414:1968 Code of practice for design and installation of joints in buildings Sep 2010 38 IS 3548:1988 Code of practice for glazing in buildings (first revision) Sep 2009 39 IS 3629:1986 Specification for structural timber in building (first revision) Sep 2010 40 IS 3630:1992 Dec 2011 41 IS 3670:1989 Code of practice for construction of non-load bearing gypsum block partitions (first revision) Code of practice for construction of timber floors (first revision) 42 IS 4101(Part 1):1967 Code of practice for external facings and veneers: Part 1 Stone facing Sep 2010 43 IS 4101(Part 2):1967 Code of practice for external facings and veneers: Part 2 Cement concrete facing Sep 2010 44 IS 4101(Part 3):1985 Code of practice for external cladding: Part 3 Wall tiling and mosaics (first revision) Sep 2010 45 IS 4407:1967 Code of practice for reed walling Sep 2012 46 IS 4597:1968 Code of practice for finishing of wood and wood based products with nitrocellulose and cold catalysed materials Sep 2010 47 IS 4891:1988 Specification for preferred cut sizes of structural timber (first revision) Sep 2009 48 IS 4920:1968 Glossary of terms applicable to roof coverings Sep 2010 49 IS 4924(Part 1):1968 Method of test for nail jointed timber trusses: Part 1 Destructive test Sep 2010 50 IS 4924(Part 2):1968 Method of test for nail jointed timber trusses: Part 2 Proof test Sep 2010 51 IS 4983:1968 Code of practice for design and construction of nailed laminated timber beams Sep 2010 52 IS 5119(Part 1):1968 Code of practice for laying and fixing of sloped roof covering: Part 1 Slating Sep 2010 53 IS 5389:1969 Code of practice for laying of hardwood parquet and wood block floors Sep 2012 54 IS 5390:1984 Code of practice for construction of timber ceilings (first revision) Sep 2010 55 IS 6061(Part 1):1971 Code of practice for construction of floor and roof with joists and filler blocks: Part 1 With hollow concrete filler blocks Sep 2012 56 IS 6061(Part 2):1981 Code of practice for construction of floor and roof with joists and filler blocks: Part 2 With hollow clay filler blocks (first revision) Sep 2010 57 IS 6061(Part 3):1981 Code of practice for construction of floor and roof with joists and filler blocks: Part 3 With precast hollow clay block joists and hollow clay filler blocks Sep 2012 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS Sep 2010 ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 46 No. of Amd. Sl No. IS Number/ DOC Number Title Reaffirm Date 58 IS 6061(Part 4):1981 Code of practice for construction of floor and roof with joists and filler blocks: Part 4 With precast hollow clay block slab Sep 2012 59 IS 6313(Part 1):1981 Code of practice for anti-termite measures in buildings: Part 1 Constructional measures (first revision) Sep 2010 60 IS 6313(Part 2):2013 Code of practice for anti-termite measures in buildings: Part 2 Pre-constructional chemical treatment measures (third revision) 61 IS 6313(Part 3):2013 Code of practice for anti-termite measures in buildings: Part 3 Treatment for existing buildings (third revision) 62 IS 6332:1984 Code of practice for construction of floors and roofs using precast doubly-curved shell units (first revision) Sep 2010 63 IS 6509:1985 Code of practice for installation of joints in concrete pavements (first revision) Sep 2010 64 IS 7683:1975 Code of practice for design, fabrication and maintenance of nail-jointed timber posts from small dimensional timber for overhead electric distribution lines for low voltages Sep 2012 65 IS 9472:1980 Code of practice for laying mosaic parquet flooring Sep 2012 66 IS 9954:1981 Pictorial surface preparation standards for painting of steel surfaces Sep 2010 67 IS 10388:1982 Specification for corrugated coir, wood, wool, cement roofing Sep 2010 68 IS 10439:1983 Code of practice for patent glazing Sep 2010 69 IS 10440:1983 Code of practice for construction of RB and RBC floors and roofs Sep 2010 70 IS 10566:1983 Methods of tests for preformed fillers for expansion joints in concrete paving and structural construction Sep 2010 71 IS 10957:1999 / ISO 2444:88 Joints in buildings - Vocabulary (first revision) Sep 2009 72 IS 10958:1984 / ISO 3447:75 General check list of functions of joints in building Sep 2012 73 IS 10959:1984 / ISO 6927:81 Glossary of terms for sealants for building purposes Sep 2012 74 IS 11096:1984 Code of practice for design and construction of bolt jointed timber construction Sep 2010 75 IS 11134:1984 Code of practice for setting out of buildings Sep 2010 76 IS 11433(Part 1):1985 Specification for one-part gun-grade polysulphide-based joints sealants: Part 1 General requirements Sep 2010 77 IS 11433(Part 2):1986 Specification for one-part gun-grade polysulphide-based joint sealants: Part 2 Methods of tests Sep 2010 Classification of joints in buildings for accommodation of dimensional deviations during construction Sep 2012 78 IS 11817:1986 / ISO 7727:84 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 47 No. of Amd. 1 79 IS 11818:1986 / ISO 6589:83 Method of test for laboratory determination of air permeability of joints in buildings Sep 2012 80 IS 12093:1987 Code of practice for laying and fixing of sloped roof covering using plain and corrugated galvanized steel sheets Sep 2012 81 IS 12118(Part 1):1987 Specification for two-parts polysulphide-based sealants: Part 1 General requirements Sep 2012 82 IS 12118(Part 2):1987 Specification for two-parts polysulphide-based sealants: Part 2 Methods of tests Sep 2012 83 IS 12506:1988 Code of practice for improved thatching of roof with rot and fire retardant treatment Sep 2009 84 IS 12727:1989 Code of practice for no-fines cast in situ cement concrete Sep 2010 85 IS 13077:1991 Guide for preparation and use of mud mortar in masonry Dec 2011 86 IS 14428:1997 Painting of structures in aggressive chemical environment Guidelines May 2013 87 IS 15183(Part 1):2002 Guidelines for maintenance management of buildings: Part 1 General Sep 2012 88 IS 15183(Part 2):2002 Guidelines for maintenance management of buildings: Part 2 Finance Sep 2012 89 IS 15183(Part 3):2002 Guidelines for maintenance management of buildings: Part 3 Labour Sep 2012 90 IS 15345:2003 Installation of frameless door and window shutters - Code of practice May 2013 91 IS 15912:2012 Structural design using bamboo - Code of Practice 92 SP 1650: 1973 Standard colours for building and decorative finishes (with supplement) (first revision) 93 SP 20(S&T): 1991 Handbook on masonry design and construction (first revision) 94 SP 21: 2005 Summaries of Indian Standards for Building Materials (first revision) 95 SP 25(S&T): 1984 Handbook on causes and prevention of cracks in building 96 SP 62(S&T): 1997 Handbook on building construction practices (excluding electrical work) DRAFT STANDARDS UNDER PRINT 1 DOC.CED 13(7883) 2 DOC.CED 13(7884) 3 DOC.CED 13(7885) 4 DOC.CED 13(7886) Draft Indian Standard Code of Practice for Use of Glass in Buildings Part 1 General Methodology for Selection Draft Indian Standard Code of Practice for Use of Glass in Buildings Part 2 Energy and Light Draft Indian Standard Code of Practice for Use of Glass in Buildings Part 3 Fire and Loading Draft Indian Standard Code of Practice for Use of Glass in Buildings Part 4 Safety Related to Human Impact 48 Sep 2005 CED 15 BUILDER'S HARDWARE SCOPE - STANDARDIZATION IN THE FIELD OF BUILDER'S HARDWARE, I.E. DOORS AND WINDOW FITTINGS SUCH AS HINGES, HANDLES, SLIDING BOLTS, RIM LATCHES ETC. Sl No. IS Number/ DOC Number Title Reaffirm Date No. of Amd. STANDARDS PUBLISHED 1 IS 204(Part 1):1991 Specification for tower bolts : Part 1 Ferous metals (fifth revision) Jan 2011 2 2 IS 204(Part 2):1992 Specification for tower bolts: Part 2 Non-ferrous metals (fifth revision) Mar 2012 3 3 IS 205:1992 Specification for non-ferrous metal butt hinges (fourth revision) Mar 2012 2 4 IS 206:2010 Specification for tee and strap hinges (fifth revision) 5 ** IS 208:1996 Specification for door handles (fifth revision) Mar 2012 5 6 IS 281:2009 Specification for mild steel sliding door bolts for use with padlocks (fourth revision) Sep 2013 7 IS 362:1991 Specification for parliament hinges (fifth revision) Jan 2011 8 IS 363:1993 Specification for hasps and staples (fourth revision) Sep 2013 9 IS 364:1993 Specification for fanlight catch (third revision) Sep 2013 10 IS 452:1973 Specification for door springs, rat-tail type (second revision) Jan 2011 11 IS 453:1993 Specification for double acting spring hinges (third revision) Sep 2013 12 IS 1019:1974 Specification for rim latches (second revision) Mar 2012 1 13 ** IS 1341:1992 Specification for steel butt hinges (fifth revision) Mar 2012 1 14 IS 1823:1980 Specification for floor door stoppers (third revision) Mar 2012 15 IS 1837:1966 Specification for fanlight pivots (first revision) Jan 2011 1 16 IS 2681:1993 Specification for non-ferrous metal sliding door bolts (aldrops) with padlocks (third revision) Sep 2013 2 17 ** IS 3564:1995 Specification for (hydraulically regulated) door closers (fourth revision) Sep 2013 18 IS 3818:1992 Specification for continuous (Piano) hinges (third revision) Mar 2012 19 IS 3828:1966 Specification for ventilator chains Jan 2011 20 IS 3843:1995 Specification for steel back flap hinges (second revision) Sep 2013 21 IS 4621:1975 Specification for indicating bolts for use in public baths and lavatories (first revision) Jan 2011 22 ** IS 4992:1975 Specification for door handles for mortice lock(vertical type) (first revision) Jan 2011 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS Sl No. IS Number/ DOC Number 1 1 ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS Title Reaffirm Date 49 No. of Amd. 23 IS 5187:1972 Specification for flush bolts (first revision) Jan 2011 1 24 IS 5899:1970 Specification for bathroom latches Mar 2012 1 25 ** IS 6315:1992 Specification for floor springs (hydraulically regulated) for heavy doors (second revision) Mar 2012 1 26 IS 6318:1971 Specification for plastic window stays and fasteners Apr 2010 1 27 IS 6343:1982 Specification for door closers (pneumatically regulated) for light doors weighing up to 40 kg (first revision) Jan 2011 28 IS 7196:1974 Specification for hold fast Mar 2012 29 IS 7197:1974 Specification for double action floor springs (without oil check) for heavy door Jan 2011 30 IS 7534:1985 Specification for sliding locking bolts for use with padlocks (first revision) Jan 2011 31 IS 8756:1978 Specification for mortice ball catches for use in wooden almirah Mar 2012 32 IS 9106:1979 Specification for rising butt hinges Mar 2012 33 IS 9460:1980 Specification for flush drop handles for drawer Mar 2012 34 IS 9899:1981 Specification for hat, coat and wardrobe hooks Mar 2012 35 IS 10019:1981 Specification for mild steel stays and fasteners Mar 2012 36 IS 10090:1982 Specification for numericals Jan 2011 37 IS 10342:1982 Specification for curtain rail system Jan 2011 38 IS 12817:2013 Specification for stainless steel butt hinges (second revision) May 2008 1 39 IS 12867:1989 Specification for PVC hand rails covers Mar 2010 1 40 IS 14912:2001 Specification for door closers concealed type (hydraulically regulated) Mar 2012 Stainless steel tower bolts - Specification Sep 2013 Stainless steel sliding door bolts for use with padlocks Specification Sep 2013 41 42 IS 15833:2009 IS 15834:2008 2 1 1 FINALIZED DRAFT UNDER PRINT 1. DOC.CED 15(7856) Draft Amendment No. 2 to IS 362:1991 Specification for Parliament Hinges (fifth revision) DRAFT STANDARD ISSUED IN WIDE CIRCULATION 1 DOC:CED 15 (7918) Steel butt hinges - Specification (sixth revision of IS 1341) 2्््््् DOC:CED 15 (7923) Draft्Amendment्No.्1्to्IS्453:1993्Specification for double acting spring hinges ््््््््््््््््््््््््््््््््््(third revision) 3 ््््््DOC:CED 15 (7924) Draft्Amendment्No.1्to्IS्281:2009्Specification for mild steel sliding door bolts for ््््््््््््््््््््््््््््््््््use with्padlocks (fourth revision) * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 50 CED 20 WOOD AND OTHER LIGNOCELLULOSIC PRODUCTS SCOPE - STANDARDIZATION IN THE FIELD OF WOOD PRODUCTS INCLUDING COMPOSITE WOOD PRODUCTS LIAISON: ISO/TC 89 (O) WOOD BASED PRODUCTS ISO/TC 89/SC 1 (O), SC 2 (O), SC 3 (O) Sl No. IS Number/ DOC Number Title Reaffirm Date No. of Amd. STANDARDS PUBLISHED 1 IS 303:1989 Specification for plywood for general purposes (third revision) Feb 2013 2 IS 652:1960 Specification for wooden separators for lead-acid storage batteries May 2009 3 IS 709:1974 Specification for medium strength aircraft plywood (first revision) May 2009 2 4 IS 710:2010 Specification for marine plywood (second revision) 5 IS 848:2006 Specification for synthetic resin adhesives for plywood (pnenolic and aminoplastic) (second revision) Jul 2011 2 6 IS 851:1978 Specification for synthetic resin adhesives for construction work (non-structural) in wood (first revision) May 2009 2 7 IS 852:1994 Specification for animal glue for general wood-working purposes (second revision) May 2009 8 IS 1328:1996 Specification for veneered decorative plywood (third revision) 9 IS 1508:1972 Specification for extenders for use in synthetic resin adhesives(urea-formaldehyde) for plywood (first revision) 10 IS 1658:2006 Specification for fibre hardboards (third revision) 11 IS 1659:2004 Specification for block boards (fourth revision) May 2009 12 IS 1734(Part 1):1983 Methods of test for plywood: Part 1 Determination of density and moisture content (second revision) Feb 2013 13 IS 1734(Part 2):1983 Methods of test for plywood : Part 2 Determination of resistance to dry heat (second revision) Feb 2013 14 IS 1734(Part 3):1983 Methods of test for plywood: Part 3 Determination of fire resistance (second revision) Feb 2013 2 15 IS 1734(Part 4):1983 Methods of test for plywood: Part 4 Determination of glue shear strength (second revision) Feb 2013 3 16 IS 1734(Part 5):1983 Methods of test for plywood: Part 5 Test for adhesion of plies (second revision) Feb 2013 17 IS 1734(Part 6):1983 Methods of test for plywood: Part 6 Determination of water resistance (second revision) Feb 2013 2 18 IS 1734(Part 7):1983 Methods of test for plywood: Part 7 Mycological test (second revision) Feb 2013 1 51 Jul 2011 6 6 May 2009 Jul 2011 2 19 IS 1734(Part 8):1983 Methods of test for plywood: Part 8 Determination of pH value (second revision) * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS Feb 2013 ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS Sl No. IS Number/ DOC Number Title Reaffirm Date 20 IS 1734(Part 9):1983 Methods of test for plywood: Part 9 Determination of tensile strength (second revision) Feb 2013 21 IS 1734(Part 10):1983 Methods of test for plywood: Part 10 Determination of compressive strength (second revision) Feb 2013 22 IS 1734(Part 11):1983 Methods of test for plywood: Part 11 Determination of static bending strength (second revision) Feb 2013 23 IS 1734(Part 12):1983 Methods of test for plywood: Part 12 Determination of scarf joint strength (second revision) Feb 2013 24 IS 1734(Part 13):1983 Methods of test for plywood: Part 13 Determination of panel shear strength (second revision) Feb 2013 25 IS 1734(Part 14):1983 Methods of test for plywood: Part 14 Determination of plate shear strength (second revision) Feb 2013 26 IS 1734(Part 15):1983 Methods of test for plywood: Part 15 Central loading of plate test (second revision) Feb 2013 27 IS 1734(Part 16):1983 Methods of test for plywood: Part 16 Vibration of plywood plate test (second revision) Feb 2013 28 IS 1734(Part 17):1983 Methods of test for plywood: Part 17 Long time loading test of plywood strips (second revision) Feb 2013 29 IS 1734(Part 18):1983 Methods of test for plywood: Part 18 Impact resistance test on the surface of plywood (second revision) Feb 2013 30 IS 1734(Part 19):1983 Methods of test for plywood: Part 19 Determination of nail and screw holding power (second revision) Feb 2013 31 IS 1734(Part 20):1983 Methods of test for plywood: Part 20 Acidity and alkalinity resistance test (second revision) Feb 2013 32 IS 2380(Part 1):1977 Methods of test for wood particle boards and boards from other lignocellulosic materials: Part 1 Preparation and conditioning of test specimens (first revision) Feb 2013 4 33 IS 2380(Part 2):1977 Methods of test for wood particle boards and boards from other lignocellulosic materials: Part 2 Accuracy of dimensions of boards (first revision) Feb 2013 4 34 IS 2380(Part 3):1977 Methods of test for wood particle boards and boards from other lignocellulosic materials: Part 3 Determination of moisture content and density (first revision) Feb 2013 4 35 IS 2380(Part 4):1977 Methods of test for wood particle boards and boards from other lignocellulosic materials: Part 4 Determination of static bending strength (first revision) Feb 2013 4 36 IS 2380(Part 5):1977 Methods of test for wood particle boards and boards from other lignocellulosic materials: Part 5 Determination of tensile strength perpendicular to surface (first revision) Feb 2013 4 37 IS 2380(Part 6):1977 Methods of test for wood particle boards and boards from other Feb 2013 4 52 No. of Amd. lignocellulosic materials: Part 6 Determination of tensile strength parallel to surface (first revision) * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS Sl No. IS Number/ DOC Number Title Reaffirm Date 38 IS 2380(Part 7):1977 Methods of test for wood particle boards and boards from other lignocellulosic materials: Part 7 Determination of compressionperpendicular to plane of the board (first revision) Feb 2013 4 39 IS 2380(Part 8):1977 Methods of test for wood particle boards and boards from other lignocellulosic materials: Part 8 Compression parallel to surface test (first revision) Feb 2013 4 40 IS 2380(Part 9):1977 Methods of test for wood particle boards and boards from other lignocellolosic materials: Part 9 Determination of resistance to shear in plane of the board (first revision) Feb 2013 4 41 IS 2380(Part 10):1977 Methods of test for wood particle boards and boards from other lignocellulosic materials: Part 10 Falling hammer impact test (first revision) Feb 2013 4 42 IS 2380(Part 11):1977 Methods of test for wood particle boards and boards from other lignocellulosic materials: Part 11 Surface hardness (first revision) Feb 2013 4 43 IS 2380(Part 12):1977 Methods of test for wood particle boards and boards from other lignocellulosic materials: Part 12 Central loading of plate test (first revision) Feb 2013 4 44 IS 2380(Part 13):1977 Methods of test for wood particle boards and boards from other lignocellulosic materials: Part 13 Long time loading bending test (first revision) Feb 2013 4 45 IS 2380(Part 14):1977 Methods of test for wood particle boards and boards from other lignocellulosic materials: Part 14 Screw and nail withdrawal test (first revision) Feb 2013 4 46 IS 2380(Part 15):1977 Methods of test for wood particle boards and boards from other lignocellulosic materials: Part 15 Lateral nail resistance (first revision) Feb 2013 4 47 IS 2380(Part 16):1977 Methods of test for wood particle boards and boards from other lignocellulosic materials: Part 16 Determination of water absorption (first revision) Feb 2013 4 48 IS 2380(Part 17):1977 Methods of test for wood particle boards and boards from other lignocellulosic materials: Part 17 Determination of swelling in water (first revision) Feb 2013 4 49 IS 2380(Part 18):1977 Methods of test for wood particle boards and boards from other lignocellulosic materials: Part 18 Determination of mass and dimensional changes caused by moisture changes (first revision) Feb 2013 4 50 IS 2380(Part 19):1977 Methods of test for wood particle boards and boards from other lignocellulosic materials: Part 19 Durability cyclic test for interior use (first revision) Feb 2013 4 51 IS 2380(Part 20):1977 Methods of test for wood particle boards and boards from other lignocellulosic materials: Part 20 Accelerated weathering cyclic test for exterior use (first revision) Feb 2013 4 52 IS 2380(Part 21):1977 Methods of test for wood particle boards and boards from other lignocellulosic materials: Part 21 Planeness test under uniform Feb 2013 4 53 No. of Amd. moisture content (first revision) * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS Sl No. IS Number/ DOC Number Title Reaffirm Date 53 IS 2380(Part 22):1981 Method of test for wood particle boards and boards from other lignocellulosic materials: Part 22 Determination of surface glueability test Feb 2013 54 IS 2380(Part 23):1981 Method of test for wood particle boards and boards from other lignocellulosic materials: Part 23 Vibration tests for particle boards Feb 2013 55 IS 3087:2005 Specification for particle boards of wood and other lignocellulosic materials (medium density) for general purposes Dec 2010 56 IS 3097:2006 Specification for veneered particle boards (second revision) 57 IS 3129:1985 Specification for low density particle boards (first revision) Dec 2010 4 58 IS 3308:1981 Specification for wood wool building slabs (first revision) Feb 2013 2 59 IS 3348:1965 Specification for fibre insulation boards May 2009 2 60 IS 3478:1966 Specification for high density wood particle boards Feb 2013 4 61 IS 3513(Part 1):1989 Specification for resin treated compressed wood laminates (compregs) Part 1 For electrical purposes (first revision) May 2009 3 62 IS 3513(Part 2):1989 Specification for resin treated compressed wood laminates (compregs):Part 2 For chemical purposes (first revision) Feb 2013 2 63 IS 3513(Part 3):1989 Specification for resin treated compressed wood laminates (compregs): Part 3 For general purposes (first revision) Feb 2013 2 64 IS 3513(Part 4):1966 Specification for resin treated compressed wood laminates (compreg): Part 4 Sampling and tests May 2009 65 IS 4834:1968 Specification for veneered wood boards for packing cases Dec 2010 2 66 IS 4835:1979 Specification for polyvinyl acetate dispersion based adhesives for wood (First revision) May 2009 2 67 IS 4859:1968 Specification for high strength aircraft plywood May 2009 3 68 IS 4990:2011 Plywood for concrete shuttering work - Specification (third revision) 69 IS 5509:2000 Specification for fire retardant plywood (second revision) Dec 2010 3 70 IS 5539:1969 Specification for preservative treated plywood May 2009 4 71 IS 7316:1974 Specification for decorative plywood using plurality of veneers for decorative faces Feb 2013 4 72 IS 7638:1999 Wood/lignocellulosic based panel products - Methods of sampling (second revision) Jul 2013 3 73 IS 9188:1979 Performance requirements for adhesive for structural laminated wood products for use under exterior exposure condition May 2009 74 IS 9307(Part 1):1979 Methods of test for wood based structural sandwich construction: Part 1 Flexure test May 2009 54 No. of Amd. 1 2 Jul 2011 75 IS 9307(Part 2):1979 Methods of test for wood based structural sandwich construction : Part 2 Edgewise compression test * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS May 2009 ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS Sl No. IS Number/ DOC Number Title 76 IS 9307(Part 3):1979 Methods of test for wood based structural sandwich construction: Part 3 Flat wise compression test May 2009 77 IS 9307(Part 4):1979 Methods of test for wood based structural sandwich construction: Part 4 Shear test May 2009 78 IS 9307(Part 5):1979 Methods of test for wood based structural sandwich construction: Part 5 Flatwise tension test May 2009 79 IS 9307(Part 6):1979 Methods of test for wood based structural sandwich construction: Part 6 Flexure creep test May 2009 80 IS 9307(Part 7):1979 Methods of test for wood based structural sandwich construction: Part 7 Cantilever vibration test May 2009 81 IS 9307(Part 8):1979 Methods of test for wood based structural sandwich construction: Part 8 Weathering test May 2009 82 IS 10701:2012 Structural plywood - Specification (first revision) June 2012 83 IS 12053:1987 Code of practice for the preparation and application of putty for repairing plywood and other wood based panels Dec 2010 84 IS 12077:1987 Code of practice for testing of timbers for plywood manufacture Dec 2010 1 85 IS 12120:1987 Code of practice for preservation of plywood and other panel products Dec 2010 3 86 IS 12406:2003 Specification for medium density fibre boards for general purposes Feb 2013 2 87््््््IS 12823:2013 Reaffirm Date No. of Amd. Wood products - Prelaminated particle boards - Specification (first्revision) 88 IS 13745:1993 Method for determination of formaldehyde content in particle board by extraction method called perforator method Feb 2013 1 89 IS 13957:1994 Specification for metal faced plywood May 2009 1 90 IS 13958:1994 Specification for bamboo mat board for general purposes May 2009 4 91 * IS 14276:1995 Specification for cement bonded particle boards May 2009 4 92 IS 14315:1995 Specification for commercial veneers May 2009 1 93 IS 14587:1998 Specification for prelaminated medium density fibre board Jul 2013 6 94 IS 14588:1999 Specification for bamboo mat veneer composite for general purposes Jul 2013 3 95 IS 14616:1999 Specification for laminated veneer lumber Jul 2013 4 96 IS 14842:2000 Specification for coir veneer board for general purposes Dec 2010 3 55 97 IS 15476:2004 Bamboo mat corrugated sheets - Specification May 2009 3 98 IS 15491:2004 Specification for medium density, coir boards for general purposes May 2009 1 99 IS 15512:2004 Code of practice for selection and use of various types for medium density fibre boards May 2009 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS Sl No. IS Number/ DOC Number Title Reaffirm Date 100 IS 15684:2006 Code of practice for use of extenders for use in synthetic resin adhesive (urea formaldehyde) for plywood Jul 2011 101 IS 15786:2008 Prelaminated cement bonded particle boards - Specification Jul 2013 102 IS 15791:2007 Musuem plywood - Specification Jul 2013 103 IS 15877:2010 Coir faced block boards - Specification 104 IS 15878:2010 Coir hardboard for general purposes - Specification 105 IS 15932(Part 1):2012 Selection and use of various types of Lignocellulosic panel products: Part 1 Medium Density Particle Boards - Code of practice 106 106 IS 15972:2012 IS 15973:2013 Bamboo-Jute corrugated & Semi-corrugated sheets - Specification Selection and use of various types of Lignocellulosic panel products: Part 2 Hardboard्-्Code of practice 106 IS 16171:2014 Veneer laminated lumber - Specification FINALISED DRAFTS UNDER PRINT 2 DOC.CED 20(7838) Draft Amendment No. 5 to IS 14276:1995 4 DOC.CED 20(7905) Selection and use of various types of lignocellulosic panel products: Part 2 Hardboard - Code of practice्[IS्15932(Part्2)] 5 DOC.CED 20(7770) Preliminated Particle Boards - Specification (first revision of IS 12823) 6. DOC:CED 20 (7877) Draft Indian Standard Cement bonded particle boards - Specification (first revision of IS 14276) 7. DOC:CED 20(7878) Draft Indian Standard Wood Based Panels - Determination of Formaldehyde Release - Part 1 Formaldehyde Chamber Method (Adoption of ISO 12460-1) DRAFT STANDARDS ISSUED IN WIDE CIRCULATION 1. DOC:CED 20(7911) Draft Amendment No. 3 to IS 12406:2003 2. DOC:CED 20(7912) Draft Amendment No. 6 to IS 14587:1993 3. DOC:CED 20(7913) Draft Amendment No. 8 to IS 12823:1990 4. DOC:CED 20(7914) Draft Amendment No. 3 to IS 3087:2005 5. DOC:CED 20(7910) Draft Amendment No. 1 to IS 15972:2012 56 No. of Amd. 1 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 57 CED 22 FIRE FIGHTING SCOPE - I) FIRE FIGHTING EQUIPMENT INCLUDING WATER FITTINGS II) FIRE FIGHTING UNITS III) FIRE DETECTION AND FIRE ALARM SYSTEMS, AND IV) HELMETS LIAISON: ISO/TC 21 EQUIPMENT FOR FIRE PROTECTION AND FIRE FIGHTING ISO/TC 21/SC 2 (O) ISO/TC 21/SC 3 (O) ISO/TC 21/SC 5 (O) ISO/TC 21/SC 6 (O) ISO/TC 94 PERSONAL SAFETY - PROTECTIVE CLOTHING AND EQUIPMENT Sl No. IS Number/ DOC Number Title Reaffirm Date No. of Amd. STANDARDS PUBLISHED 1 IS 884:1985 Specification for first-aid hose reel for fire fighting (first revision) Nov 2010 2 IS 901:1988 Specification for couplings, double male and double female, instantaneous pattern for fire fighting (third revision) Aug 2013 3 IS 902:1992 Specification for suction hose couplings for fire fighting purposes (third revision) 4 IS 903:1993 Specification for fire hose delivery couplings, branch pipe, nozzles and nozzlespanner (fourth revision) Aug 2013 5 IS 904:1983 Specification for 2-way and 3-way suction collecting heads for fire fighting purposes (second revision) Nov 2010 6 IS 905:1980 Specification for delivery breechings, dividing and collecting instantaneous pattern for fire fighting purposes (second revision) Sep 2012 7 IS 906:1988 Specification for revolving branch pipe for fire fighting (third revision) Nov 2010 8 IS 907:1984 Specification for suction strainers, cylindrical type for fire fighting purposes (second revision) Nov 2010 9 IS 908:1975 Specification for fire hydrant, stand post type (second revision) Nov 2010 10 IS 909:1992 Specification for underground fire hydrant, sluice valve type (third revision) Sep 2012 Specification for combined key for hydrant, hydrant cover and lower valve (second revision) Sep 2012 11 IS 910:1980 Sep 2012 2 12 IS 926:1985 Specification for fireman's axe (second revision) Nov 2010 13 IS 927:1981 Specification for fire hooks (second revision) Sep 2012 14 IS 928:1984 Specification for fire bells (second revision) Nov 2010 15 IS 937:1981 Specification for washers for water fittings for fire fighting purposes (second revision) Sep 2012 16 IS 939:1977 Specification for snatch block for use with fibre rope for fire brigade use (first revision) Sep 2012 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 58 3 2 1 1 1 2 2 Sl No. IS Number/ DOC Number Title Reaffirm Date 17 IS 941:1985 Specification for blower and exhauster for fire fighting (second revision) Nov 2010 18 IS 942:1982 Functional requirements for 275 l/min portable pump set for fire fighting (second revision) Nov 2010 19 IS 943:1979 Functional requirements for 680-l/min trailer pump for fire brigade use (second revision) Aug 2013 20 IS 944:1979 Functional requirements for 1800-l/min trailer pump for fire brigade use (second revision) Sep 2012 1 21 IS 947:1985 Functional requirements for towing tender for trailer fire pump for fire brigade use (first revision) Sep 2012 1 22 IS 948:1983 Functional requirements for water tender type `A' for fire brigade use (second revision) Nov 2010 1 23 IS 949:2012 Functional requirements for emergency (rescue) tender for fire brigade use (second revision) Nov 2010 24 IS 950:2012 Functional requirements for water tender, Type B for fire brigade use (third revision) 25 IS 951:2003 Functional requirements for crash tender for air fields (fourth revision) 26 IS 952:2012 Specification for fognozzle for fire brigade use (second revision) 27 IS 955:1980 Functional requirements for dry powder tender for fire brigade use (150 kg capacity) (first revision) 28 IS 956:2004 Functional requirements for rescue tender for air fields (second revision) Jan 2010 29 IS 957:1967 Specification for control van for fire brigade use Nov 2010 30 IS 1941(Part 1):1976 Functional requirements for electric motor sirens: Part 1 AC, 3 Phase 50 hz, 415 volts type (second revision) Sep 2012 31 IS 2097:2012 Specification for foam making branch pipe (second revision) 32 IS 2175:1988 Specification for heat sensitive fire detectors for use in automatic fire alarm system (second revision) Nov 2010 33 IS 2189:2008 | ISO/TR 7240-14 Code of practice for selection, installation and maintenance of automatic fire detection and alarm system (fourth revision) Aug 2013 34 IS 2190:2010 | ISO 3941 Selection, installation and maintenance of first-aid fire extinguishers - Code of practice (fourth revision) 35 IS 2546:1974 Specification for galvanized mild steel fire bucket (first revision) Nov 2010 2 36 IS 2696:1974 Functional requirements for 1125-l/min light fire engine (first revision) (Superseding IS 938) Sep 2012 2 37 IS 2745:1983 Specification for non-metal helmet for firemen and civil defence personnel (second revision) Nov 2010 3 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS 2 2 Aug 2013 Aug 2013 ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 59 No. of Amd. 1 3 Sl No. IS Number/ DOC Number Title Reaffirm Date 38 IS 2871:2012 Specification for branch pipe, universal for fire fighting purposes (second revision) 39 IS 2878:2004 Specification for fire extinguisher, carbon dioxide type(portable and trolley mounted ) (third revision) Jan 2010 8 40 IS 2925:1984 | ISO 3873 Specification for industrial safety helmets (second revision) Nov 2010 4 41 IS 2930:1980 Functional requirements for hose laying tender for fire brigade use (first revision) Sep 2012 1 42 IS 3582:1984 Specification for basket strainers for fire fighting purposes (cylindrical type) (first revision) Nov 2010 43 IS 3744:1985 Specification for hose binding machine (first revision) Nov 2010 44 IS 3844:1989 Code of practice for installation and maintenance of internal fire hydrants and hose reels on premises (first revision) Nov 2010 45 *IS 4151:1993 Specification for protective helmets for motorcycle riders (third revision) Aug 2013 46 IS 4308:2003 Specification for dry chemical powder for fighting B and C Class fires (second revision) Aug 2013 47 IS 4571:1977 Specification for aluminium extension ladders for fire brigade use (first revision) Nov 2010 48 IS 4643:1984 Specification for suction wrenches for fire brigade use (first revision) Nov 2010 49 IS 4861:1984 Specification for dry powder for fighting fires in burning metals (first revision) Nov 2010 1 50 IS 4862(Part 1):1986 Specification for portable fire extinguishers for aircraft : Part 1 Halon 1211 Type (first revision) Nov 2010 3 51 IS 4927:1992 Specification for unlined flax canvas hose for fire fighting (first revision) Sep 2012 2 52 IS 4928:1986 Specification for delivery valve for centrifugal fire pump outlets(first revision) Nov 2010 53 IS 4947:2006 Specification for gas cartridges for use in fire extinguishers (third revision) Feb 2012 1 54 IS 4989:2006 Foam concentrate for producing mechanical foam for fire fighting - Specification (third revision) [Amalgamating IS 4989(Part 1):1985, IS 4989(Part 2):1984 and IS 4989(Part 3):1987] Feb 2012 2 55 IS 4989(Part 4):2003 Specification for multipurpose aqueous film forming foam liquid concentrate for extinguishing hydrocarbon and polar solvent fires Aug 2013 2 56 IS 5131:2002 Specification for dividing breeching with control for fire brigade use (second revision) Sep 2012 57 *IS 5290:1993 Specification for landing valves (third revision) Aug 2013 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 60 No. of Amd. 2 4 5 6 Sl No. IS Number/ DOC Number Title Reaffirm Date 58 IS 5486:1985 Specification for quick release knife (first revision) Nov 2010 59 IS 5505:1985 Specification for multi-edged rescue axe (non-wedging) (first revision) Nov 2010 60 IS 5612(Part 1):1977 Specification for hose-clamps and hose-bandages for fire brigade use: Part 1 Hose-clamps (first revision) Sep 2012 61 IS 5612(Part 2):1977 Specification for hose-clamps and hose bandages for fire brigade use: Part 2 Hose bandages (first revision) Sep 2012 62 IS 5714:1981 Specification for hydrant, stand-pipe for fire fighting (first revision) Sep 2012 63 IS 5888:1970 Code of practice for design and construction of fire service drilltower Nov 2010 64 IS 5896(Part 1):1970 Code of practice for selection, operation and maintenance of special fire fighting appliances: Part 1 Combined foam and CO2 crash tender Nov 2010 65 IS 5896(Part 3):1975 Code of practice for selection, operation and maintenance of fire fighting appliances: Part 3 Turntable ladders Sep 2012 66 IS 6026:1985 Specification for hand-operated sirens (first revision) Nov 2010 67 IS 6067:1983 Functional requirements for water tender type `X' for fire brigade use(first revision) Nov 2010 68 IS 6070:1983 Code of practice for selection, operation and maintenance of trailer fire pumps, portable pumps, water tenders and motor fire engines (first revision) Nov 2010 69 IS 7673:2004 | ISO 8421-1 Glossary of terms for fire fighting equipment (first revision) Aug 2013 70 IS 7692:1993 Specification for head forms for testing of helmets (first revision) Aug 2013 71 IS 8090:1976 Specification for couplings, branch pipe, nozzle, used in hose reel tubing for fire fighting Nov 2010 72 IS 8096:1992 Specification for fire beaters (first revision) Sep 2012 73 IS 8149:1994 Functional requirements for twin CO2 fire extinguishers (trolley mounted)(first revision) Nov 2010 2 74 IS 8423:1994 Specification for controlled percolating hose for fire fighting (first revision) Nov 2010 3 75 IS 8442:2008 Functional requirements for stand post type water monitor for fire fighting (first revision) Aug 2013 76 IS 9562:1980 Specification for non-metal helmet for police force Sep 2012 77 IS 9668:1990 Code of practice for provision and maintenance of water supplies and fire fighting (first revision) Nov 2010 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 61 No. of Amd. 1 1 1 5 Sl No. IS Number/ DOC Number Title 78 IS 9695:1980 Methods of sampling of helmets 79 IS 9972:2002 Specification for automatic sprinkler heads for fire protection service (first revision) Sep 2012 80 * IS 9973:1981 Specification for visor for scooter helmets Sep 2012 81 IS 9995:1981 Specification for visor for non-metal police and firemen's Sep 2012 1 82 IS 10460:1983 Functional requirements for small foam tender for fire brigade Nov 2010 1 83 IS 10658:1999 Specification for higher capacity dry powder fire extinguisher (trolley mounted) (first revision) Nov 2010 8 84 IS 10993:1984 Functional requirements for 2000-kg dry powder tender for fire brigade use Nov 2010 1 85 IS 11101:1984 Specification for extended branch pipe for fire brigade use Sep 2012 86 IS 11108:1984 Specification for portable fire extinguisher halons-1211 type Nov 2010 87 IS 11360:1985 Specification for smoke detectors for use in automatic electrical fire alarm system Nov 2010 88 IS 11833:1986 Specification for dry powder fire extinguisher for metal fires Sep 2012 4 89 IS 12717:1989 Functional requirements of fire fighting equipment - High capacity portable pumpset (1100-1600 L/min) Nov 2010 1 90 IS 12796:1989 Specification for fire rake Nov 2010 91 IS 12805:1989 Tool Mcleod for fighting forest fires Nov 2010 Code of practice for design and installation of fixed foam fire extinguishing system: Part 1 Low expansion foam Nov 2010 92 IS 12835(Part 1):1989 | ISO 7203-1 Reaffirm No. of Date Amd. Nov 2010 4 93 IS 12853:1989 Specification for pulaski tool for forest fires Nov 2010 94 IS 12859:1989 Specification for brush hook for forest fires Nov 2010 95 IS 12861:1989 Specification for double bit axe for forest fires Nov 2010 96 IS 12862:1989 Specification for fire fighting shovel for forest fires Nov 2010 97 IS 13039:1991 Code of practice for external hydrant systems provision and maintenance Nov 2010 98 IS 13385:1992 Specification for fire extinguisher- 50 litre capacity wheel mounted water type (Gas Cartridge) Sep 2012 8 99 IS 13386:1992 Specification for fire extinguisher 50 litre capacity mechanical foam type Sep 2012 10 Specification for dry chemical powder for fighting ABC Class Jan 2010 5 100 IS 14609:1999 | ISO 7202 101 IS 14851:2000 Code of practice for maintenance of fire hose Nov 2010 102 IS 14933:2001 Specification for high pressure fire fighting hose Nov 2010 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 62 Sl No. IS Number/ DOC Number Title Reaffirm Date 103 IS 14951:2001 Specification for fire extinguisher, 135 litre capacity mechanical foam type Nov 2010 104 IS 15051:2001 High pressure fire hose delivery couplings - Specification Sep 2012 105 IS 15105:2002 | ISO 6182-1 Design and installation of fixed automatic sprinkler fire extinguishing systems – Code of Practice Sep 2012 106 IS 15220:2002 | ISO 7201-1 Specification for halon 1211 and halon 1301 - halogented hydrocarbon - fire extinguishing media for fire protection Sep 2012 107 IS 15221:2002 | ISO 7201-2 Code of practice for safe handling and transfer procedure of halon 1121 and halon 1301- (halogonated hydrocarbon) - fire extinguishing media Sep 2012 108 IS 15222:2002 | ISO 5923 Specification for carbon-dioxide as fire extinguishing media for fire protection Sep 2012 109 IS 15301:2003 Code of practice for installation and maintenance of fire fighting pump Aug 2013 110 IS 15325:2003 Code of practice for design and installation of fixed automatic high and medium velocity water spray system Aug 2013 111 IS 15493:2004 | ISO 14520-1 112 IS 15496:2004 113 Gaseous fire extinguishing systems - General requirements Jan 2010 Inspection and maintenance of gaseous fire extinguishing systems - Code of practice Jan 2010 IS 15497:2004 | ISO 14520-12 Gaseous fire extinguishing systems IG 01 extinguishing systems Jan 2010 114 IS 15501:2004 | ISO 14520-15 Gaseous fire extinguishing systems IG 541 extinguishing Jan 2010 115 IS 15505:2004 | ISO 14520-6 Gaseous fire extinguishing systems - HCFC Blend A extinguishing systems Jan 2010 116 IS 15506:2004 | ISO 14520-14 Gaseous fire extinguishing systems - IG 55 - extinguishing systems Jan 2010 117 IS 15517:2004 | ISO 14520-9 Gaseous fire extinguishing systems - HFC 227ea (Hepta Fluoro Propane) extinguishing systems Jan 2010 118 IS 15519:2004 Water mist fire protection systems - System design, installation and commissioning - Code of practice Jan 2010 119 IS 15525:2004 | ISO 14520-13 Gaseous fire extinguishing systems - IG 100 extinguishing Jan 2010 120 IS 15528:2004 | ISO 6183 Gaseous fire extinguishing systems - Carbon dioxide total flooding and local application (Sub-floor and in-cabinet), high and low pressure (refrigerated) systems Jan 2010 121 IS 15682:2006 Fire fighting vehicle and equipment - Symbols for operator controls and other display Feb 2012 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 63 No. of Amd. 2 1 2 Sl No. IS Number/ DOC Number Title Reaffirm Date 122 IS 15683:2006 | ISO 7165:2009 Portable fire extinguishers - Performance and construction Specification Feb 2012 123 IS 15811:2008 Long-range water-cum-foam monitor with self-inducting, aspirating and non-aspirating jet and spray/fog nozzle for fire fighting - Specification Nov 2008 124 IS 15821:2008 Gaseous fire extinguishing system - Physical properties and system design - CF3I Extinguishant 125 IS 15835:2009 Gaseous Fire Extinguishing Systems HCFC - 125 Extinguishing Systems 126 IS 15908:2011 Selection, installation and maintenance of control and indicating equipments for fire detection and alarm system Code of Practice 127 IS 16018:2012 Wheeled fire extinguisher - Performance and construction Specification 128 IS 16088:2012 Chlorinated polyvinyl chloride (CPVC) pipes for automatic sprinkler fire extinguishing system - Specification 129 IS 16095:2013 Hazmat vehicle - Specification 130 IS 16109:2013 Turntable Ladder - Specification 131 IS / ISO 6182-7 :2004 Fire Protection - Automatic Sprinkler Systems Part 7 Requirements and Test Method for Early Suppression Fast Response (ESFR) Sprinklers 132 IS/ ISO 7240-5 :2003 Fire Detection and Alarm Systems Part 5 Point-Type Heat Detectors 133 IS/ ISO 7240-7 :2011 Fire Detection and Alarm Systems Part 7 Point-Type Smoke Detectors using Scattered Light, Transmitted light or Ionization 134 IS/ ISO 7240-11 :2011 Fire Detection and Alarm Systems Part 11 Manual Call Points 135 IS/ ISO 7240-15 :2004 Fire Detection and Alarm Systems Part 15 Point-Type Fire Detectors using Scattered Light, Transmitted light or Ionization Sensor in Combination with a Heat Sensor DOC.CED 22(7753) Gaseous fire - Extinguishing systems - Physical properties and system design FK-5-1-12 extinguishant 2 DOC.CED 22(7808) Draft Indian Standard External Hydrant Systems - Provision and Maintenance - Code of Practice 3 DOC.CED 22(7887) Specification for protective helmets for two wheeler riders (fourth revision of IS 4151) * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 64 4 Oct 2008 FINALISED DRAFTS UNDER PRINT 1 No. of Amd. 1 DRAFTS COMPLETED WIDE CIRCULATION 1 DOC.CED 22(7871) Amendment No. 1 to IS 2190 2 DOC.CED 22(7872) Amendment No. 3 to IS 4989 3 DOC.CED 22(7873) Amendment No. 1 to IS 16018 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 65 CED 24 PUBLIC HEALTH ENGINEERING SCOPE - CODE OF PRACTICE FOR WATER SUPPLY, DRAINAGE AND SANITATION IN BUILDINGS, INCLUDING LAYING OF PIPELINES, SMALL SEWAGE TREATMENT PLANTS, ANCILLARY STRUCTURES FOR WATER SUPPLY AND SEWERAGE AND STANDARDIZATION OF EQUIPMENT USED IN PUBLIC HEALTH ENGINEERING INCLUDING THEIR DESIGN, MANUFACTURE, TESTING, OPERATION AND MAINTENANCE Sl No. IS Number/ DOC Number Title Reaffirm Date No. of Amd. STANDARDS PUBLISHED 1 * IS 1172:1993 Code of basic requirements for water supply, drainage and sanitation (fourth revision) Nov 2012 2 IS 1742:1983 Code of practice for building drainage (second Revision) Nov 2012 3 IS 2064:1993 Code of practice for selection, installation and maintenance of sanitary appliances (second Revision) Nov 2012 4 IS 2065:1983 Code of practice for water supply in buildings (second revision) Feb 2012 5 IS 2470(Part 1):1985 Code of practice for installation of septic tanks: Part I design, criteria and construction (second revision) Feb 2012 6 IS 2470(Part 2):1985 Code of practice for installation of septic tanks: Part 2 Secondary treatment and disposal of septic tank effluent Feb 2012 7 IS 3114:1994 Code of practice for laying of cast iron pipes (second revision) 8 IS 4111(Part 1):1986 Code of practice for ancillary structures in sewerage system: Part I Manholes (first revision) Feb 2012 9 IS 4111(Part 2):1985 Code of practice for ancillary structures in sewerage system: Part II Flusing tanks (first revision) Feb 2012 10 IS 4111(Part 3):1985 Code of practice for ancillary structures in sewerage system: Part III Inverted syphon (first revision) Feb 2012 11 IS 4111(Part 4):1968 Code of practice for ancillary structures in sewerage system: Part 4 Pumping stations and pumping mains (rising mains) Feb 2012 12 IS 4111(Part 5):1993 Code of practice for ancillary structures in sewerage system: Part 5 Tidal outfalls Jul 2009 13 IS 4127:1983 Code of practice for laying of glazed stoneware pipes (first revision) Feb 2012 14 IS 5329:1983 Code of practice for sanitary pipe work above ground for buildings (first revision) Feb 2012 15 IS 5611:1987 Code of practice for construction of waste stabilization ponds (faculative type) (first revision) Nov 2012 16 IS 5822:1994 Code of practice for laying of electrically welded steel pipes for water supply (second revision) Jul 2009 17 IS 6279:1971 Specification for equipment for grit removal devices Jul 2010 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS Jul 2009 ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 66 2 Sl No. IS Number/ DOC Number Title Reaffirm Date 18 IS 6280:1971 Specification for sewage screens 19 IS 6295:1986 Code of practice for water supply and drainage in high altitudes and/or sub-zero temperature regions (first revision) Feb 2012 20 IS 6924:1973 Code of practice for the construction of refuse chutes in multistoreyed buildings Feb 2012 21 IS 7090:1985 Guidelines for rapid mixing devices (first revision) 22 IS 7208:1992 Guidelines for flocculator devices (first revision) Feb 2012 23 IS 7232:1974 Method for imhoff cone test Nov 2012 24 IS 7558:1974 Code of practice for domestic hot water installations Feb 2012 25 IS 7740:1985 Code of practice for construction and maintenance of road gullies (first revision) Feb 2012 26 IS 8413(Part 1):1977 Requirements for biological treatment equipment: Part 1 Trickling filters Jul 2010 27 IS 8413(Part 2):1982 Requirements for biological treatment and equipment: Part 2 Activated sludge process and its modifications Jul 2010 28 IS 8419(Part 1):1977 Requirements for filtration equipment : Part 1 Filtration media - sand and gravel Jul 2010 29 IS 8419(Part 2):1984 Requirements for rapid sand gravity filtration equipment: Part 2 Under drainage system Jul 2010 30 IS 9110:1979 Specification for hand operated augers for cleaning waterclosets pipes and sewers Jul 2010 31 IS 9222(Part 1):1990 Recommendations for handling and dosing devices for chemicals for water treatment: Part I Coagulants (first revision) Jul 2010 32 IS 10037(Part 1):1981 Requirements for sludge dewatering equipment: Part I Sludge drying beds-sand, gravel and under drains Nov 2012 33 IS 10037(Part 2):1983 Requirements for sludge de-watering equipment: Part 2 Vacuum filtration equipment Jul 2010 34 IS 10037(Part 3):1983 Requirements for sludge de-watering equipment: Part 3 Centrifugal equipment (Solid bowl type) Jul 2010 35 IS 10053:1981 Requirements for equipment for jackson candle turbidimeter and determination of turbidity Nov 2012 36 IS 10261:1982 Requirements for settling tank (clarifier equipment) for waste water treatment Jul 2010 37 IS 10313:1982 Requirements for settling tank (clarifier equipment) for water treatment plant Jul 2010 38 IS 10446:1983 Glossary of terms relating to water supply and sanitation 39 IS 10552:1983 Specification for buckets to be used in power driven bucket type sewer cleaning machine * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS Jul 2010 Jul 2010 Feb 2012 Jul 2010 ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 67 No. of Amd. Sl No. IS Number/ DOC Number Title Reaffirm Date 40 IS 10553(Part 1):1983 Requirements for chlorination equipment: Part I General guidelines for chlorination plants including handling, storage and safety of chlorine cylinders and drums 41 IS 10553(Part 2):1983 Requirements for chlorination equipment: Part 2 Vacuum feed type chlorinators Jul 2010 42 IS 10553(Part 4):1983 Requirements for chlorination equipment: Part 4 Gravity feed type gaseous chlorinators Jul 2010 43 IS 10553(Part 5):1987 Requirements of chlorination equipment: Part 5 Bleaching powder solution feeder displacement type chlorinator Nov 2012 44 IS 10595:1983 Requirements for power driven bucket-type sewer cleaning machine Jul 2010 45 IS 11117:1984 Requirements for power driven rodding machine for sewers Jul 2010 46 IS 11208:1985 Guidelines for registration of plumbers 47 IS 11387:1985 Requirements for high pressure jetting machine for sewer Jul 2010 48 IS 11397:1985 Specification for attachment tools for power driven rodding machine for sewers Jul 2010 49 IS 11401(Part 1):1985 Requirements for slow sand filters: Part 1 General guidelines 50 IS 11401(Part 2):1990 General requirements for slow sand filters Part 2 Design, construction, operation and maintenance 51 IS 11906:1986 Recommendations for cement mortar lining for cast iron mild steel and ductile-iron pipes and fittings for transportation of Nov 2012 52 IS 11925:1986 Specification for pitch-impregnated fibre pipes and fittings for drainage purposes Nov 2012 53 IS 11931:1987 Specification for sewer cleaning metal rods Nov 2012 54 IS 11972:1987 Code of practice for safety precautions to be taken when entering a sewerage system Nov 2012 55 IS 12183(Part 1):1987 Code of practice for plumbing in multi-storeyed buildings: Part 1 Water supply Jul 2009 56 IS 12251:1987 Code of practice for drainage of building basements Jul 2009 57 IS 12288:1987 Code of practice for use and laying of ductile iron pipes Nov 2012 58 IS 12314:1987 Code of practice for sanitation with leaching pits for rural community Nov 2012 59 IS 13166:1992 Guidelines for evaluation and testing of mechanical surface aerators Feb 2012 60 IS 13496:1992 General requirements of suction machine for cleaning sewers, manholes and ancillary structures provided on sewer line and closed storm water drains Nov 2012 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS Nov 2012 1 Feb 2012 Nov 2012 Jul 2009 ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 68 No. of Amd. 1 Sl No. IS Number/ DOC Number Title 61 Handbook on water supply and drainage with special emphasis on plumbing SP 35(S&T): 1987 Reaffirm Date DRAFT STANDARDS FINALIZED BUT NOT YET UNDER PRINT 1 DOC.CED 24(7824) Draft amendment no. 1 to IS 5822 2 DOC.CED 24(7880) Draft Amendment No. 1 to IS 3114 3. DOC.CED 24(7882) Draft Amendment No. 1 to IS 4111 (Part 5) * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 69 No. of Amd. CED 29 CONSTRUCTION MANAGEMENT(INCLUDING SAFETY IN SCOPE - FORMULATION OF STANDARDS IN THE FIELD OF CONSTRUCTION MANAGEMENT AND RELATED ASPECTS. FORMULATION OF STANDARDS LAYING DOWN SAFETY REQUIREMENTS IN THE VARIOUS OPERATIONS INVOLVED IN DIFFERENT TYPES OF CIVIL ENGINEERING CONSTRUCTION. Sl No. IS Number/ DOC Number Title Reaffirm Date No. of Amd. STANDARDS PUBLISHED 1 IS 3696(Part 1):1987 Safety code of scaffolds and ladders: Part 1 Scaffolds (first revision) Feb 2012 2 IS 3696(Part 2):1991 Safety code of scaffolds and ladders: Part 2 Ladders (first revision) Feb 2012 3 IS 3764:1992 Code of safety for excavation work (first revision) Feb 2012 4 * IS 4014(Part 2):1967 Code of practice for steel tubular scaffolding: Part 2 Safety regulations for scaffolding Sep 2010 5 * IS 4081:1986 Safety code for blasting and related drilling operations (first revision) Sep 2010 6 IS 4082:1996 Recommendations on stacking and storage of construction materials and components at site (second revision) May 2013 7 IS 4130:1991 Safety code for demolition of buildings (second revision) Feb 2012 8 IS 4138:1977 Safety code for working in compressed air (first revision) Feb 2012 9 IS 4756:1978 Safety code for tunneling work (first revision) Feb 2012 10 IS 4912:1978 Safety requirements for floor and wall openings, railings and toe boards (first revision) Feb 2012 11 * IS 5121:1969 Safety code for piling and other deep foundations Sep 2010 12 * IS 5916:1970 Safety code for construction involving use of hot bituminous materials Sep 2010 13 IS 7272(Part 1):1974 Recommendations for labour output constants for building work: Part 1 North zone Sep 2010 14 IS 7293:1974 Safety code for working with construction machinery Feb 2012 15 IS 7969:1975 Safety code for handling and storage of building materials Feb 2012 16 IS 8989:1978 Safety code for erection of concrete framed structures Sep 2010 17 IS 10067:1982 Material constants in building works Sep 2010 18 IS 10291:1982 Safety code for dress divers in civil engineering works Feb 2012 19 IS 10302:1982 Unified nomenclature of workmen for civil engineering Sep 2010 20 IS 13415:1992 Code of safety for protective barriers in and around buildings Feb 2012 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 70 1 1 Sl No. IS Number/ DOC Number Title Reaffirm Date 21 IS 13416(Part 1):1992 Recommendations for preventive measures against hazards at workplaces: Part 1 Falling material hazards prevention Feb 2012 22 IS 13416(Part 2):1992 Recommendations for preventive measures against hazards at workplaces: Part 2 Fall prevention Feb 2012 23 IS 13416(Part 3):1994 Recommendations for preventive measures against hazards at workplaces: Part 3 Disposal of debris May 2013 24 IS 13416(Part 4):1994 Recommendations for preventive measures against hazards at workplaces: Part 4 Timber structure May 2013 25 IS 13416(Part 5):1994 Recommendations for preventive measures against hazards at workplaces: Part 5 Fire protection Jul 2008 26 IS 13430:1992 Code of practice for safety during additional construction and alteration to existing buildings 27 IS 15883(Part 1):2009 Guidelines for construction project management: Part 1 General 28 IS 15883(Part 2):2013 Guidelines for construction project management: Part 2 Time management 29 SP 70: 2001 Feb 2012 Handbook on construction safety practices FINALISED DRAFTS UNDER PRINT 1 DOC.CED 29(7778) Draft Indian Standards Guidelines for Construction Project Management: Part 5 Health and Safety Management [IS15883(Part 5)] 2 DOC.CED 29(7773) Draft Indian Standard Code of practice for steel tubular scaffolding: Part 2 Safety regulations for scaffolding [First Revision of IS 4014(Part 2)] 3 DOC.CED 29(7774) Draft Indian Standard Safety code for blasting and related drilling operations (Second Revision of IS 4081) 4 DOC.CED 29(7775) Draft Indian Standard Safety code for piling and other deep foundations (First Revision of IS 5121) 5 DOC.CED 29(7776) Draft Indian Standard Safety code for constructions involving use of hot bituminous materials (First Revision of IS 5916) DRAFT STANDARDS COMPLETED IN WIDE CIRCULATION 1 DOC.CED 29(7906) 2 DOC.CED 29(7907) 3 DOC.CED 29(7908) 4 DOC.CED 29(7909) Draft Indian Standard Guidelines for Construction Project Management: Part 3 Cost Management [IS15883(Part 3)] Draft Indian Standard Guidelines for Construction Project Management: Part 4 Quality Management [IS15883(Part 4)] Draft Indian Standard Guidelines for Construction Project Management: Part 6 Scope Management [IS15883(Part 6)] Draft Indian Standard Guidelines for Construction Project Management: Part 8 Risk Management [IS15883(Part 8)] * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 71 No. of Amd. CED 30 SCOPE - CLAY AND STABILIZED SOIL PRODUCTS FOR CONSTRUCTION STANDARDIZATION IN THE FIELD OF BURNT, UNBURNT CLAY AND STABILIZED SOIL PRODUCTS FOR CONSTRUCTION Sl No. IS Number/ DOC Number Title Reaffirm Date No. of Amd. STANDARDS PUBLISHED 1 IS 654:1992 Clay roofing tiles, mangalore pattern - Specification (third revision) Dec 2011 2 IS 1077:1992 Common burnt clay building bricks - Specification (fifth revision) Dec 2011 3 IS 1464:1992 Clay ridge and ceiling tiles - Specification (second revision) Dec 2011 4 IS 1478:1992 Clay flooring tile - Specification (second revision) Dec 2011 5 IS 1725:2013 Stabilized soil blocks used in general building construction - Specification (second revision) 6 IS 2117:1991 Guide for manufacture of hand-made common burnt clay building bricks (third revision) Dec 2011 7 IS 2180:1988 Specification for heavy duty burnt clay building bricks (third revision) Dec 2011 8 IS 2222:1991 Specification for burnt clay perforated building bricks (fourth revision) Dec 2011 9 IS 2248:1992 Glossary of terms relating to clay products for buildings (second revision) Dec 2011 10 IS 2690(Part 1):1993 Burnt clay flat terracing tiles- Specification : Part 1 Machine made (second revision) Dec 2011 11 IS 2690(Part 2):1992 Burnt clay flat terracing tiles - Specification : Part 2 Hand made (second revision) Dec 2011 12 IS 2691:1988 Specification for burnt clay facing bricks (second revision) Jan 2011 13 IS 3367:1993 Burnt clay tiles for use in lining irrigation and drainage works Specification (second revision) Dec 2011 14 IS 3495(Part 1-4):1992 Methods of tests of burnt clay building bricks: (third revision) Part 1 Determination of compressive strength Part 2 Determination of water absorption Part 3 Determination of efflorescence Part 4 Determination of warpage Dec 2011 15 IS 3583:1988 Specification for burnt clay paving bricks (second revision) Jan 2011 16 IS 3951(Part 1):2009 Specification for hollow clay tiles for floors and roofs Part 1 Filler type (first revision) 17 IS 3951(Part 2):2009 Hollow clay tiles for floors and roofs-Specification: Part 2 Structural type (second revision) 18 IS 3952:2013 Specification for burnt clay hollow bricks and्blocks्for walls and partitions (third revision) * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 72 1 1 2 1 Sl No. IS Number/ DOC Number Title Reaffirm Date 19 IS 3978:1993 Manufacture of burnt clay Mangalore pattern roofing tiles Code of practice (first revision) Dec 2011 20 IS 4885:1988 Specification for sewer bricks (first revision) Jan 2011 21 IS 5454:1978 Methods of sampling of clay building bricks (first revision) Jan 2011 22 IS 5779:1986 Specification for burnt clay soling bricks (first revision) Dec 2011 23 IS 6165:1992 Dimensions for special shapes of clay bricks (first revision) Dec 2011 24 IS 7556:1988 Specification for burnt clay jallies (first revision) Jan 2011 25 IS 8920:1978 Methods for sampling of burnt clay tiles July 2013 26 IS 11650:1991 Guide for manufacture of common burnt clay building bricks by semi-mechanized process (first revision) Dec 2011 27 IS 13317:1992 Clay roofing country tiles, half round and flat tiles - Specification Dec 2011 28 IS 13757:1993 Burnt clay fly ash building bricks - Specification Dec 2011 FINALIZED DRAFTS UNDER PRINT 1 DOC.CED 30(7817) Draft Indian Standard Burnt clay hollow bricks and blocks for walls and partitions - Specification (second revision of IS 3952) DRAFT STANDARDS ISSUED IN WIDE CIRCULATION 1 DOC.CED 30(7934) Draft Indian Standard for Burnt clay facing bricks - Specification (third revision of IS 2691) * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 73 No. of Amd. 1 1 1 CED 35 FURNITURE SCOPE - STANDARDIZATION IN THE FIELD OF FURNITURE INCLUDING FURNITURE USED FOR GENERAL PURPOSES, OFFICES, SCHOOLS, STADIUM, AUDITORIUM, CINEMA HOUSES, RESTAURANTS, LIBRARY, ETC LIAISON: ISO/TC 136 (O) FURNITURE Sl No. IS Number/ DOC Number Title Reaffirm Date No. of Amd. STANDARDS PUBLISHED 1 IS 1829(Part 1):1978 Specification for library furniture and fittings: Part 1 Timber (first revision) May 2010 2 IS 1829(Part 2):1993 Library furniture and fittings : Part 2 Steel - Specification (first revision) Sep 2012 3 IS 1883:1983 Specification for metal shelving racks adjustable type (third revision) May 2010 4 IS 2695:1993 Specification for drawing filing equipment (second revision) Sep 2012 5 IS 3312:1984 Specification for steel shelving cabinets (adjustable type) (second revision) May 2010 6 IS 3313:1983 Specification for steel filing cabinets for general office purposes (second revision) May 2010 7 IS 3314:1984 Specification for steel clothes lockers (second revision) May 2010 8 IS 3497:1992 Steel wardrobes (adjustable type) - Specification (second revision) Sep 2012 9 IS 3498:1993 Metal table (office type) - Specification (third revision) Sep 2012 10 IS 3499(Part 1):1985 Specification for metal chairs for office purposes: Part 1 Nonrevolving and non-tilting (second revision) May 2010 11 IS 3499(Part 2):1985 Specification for metal chairs for office purposes: Part 2 Revolving and tilting (Second Revision) May 2010 12 IS 3663:1991 Dimensions of tables and chairs for office purposes (second revision) May 2010 13 IS 3761:1983 Specification for metal side racks (adjustable type) (first revision) May 2010 14 IS 3762:1979 Specification for metal waste paper bins (first revision) May 2010 15 IS 3763:1983 Specification for metal folding chairs (first revision) May 2010 16 IS 3791:1983 Specification for metal paper trays (first revision) May 2010 17 IS 3845:1966 Code of practice for joints used in wooden furniture May 2010 18 IS 4103:1977 Specification for metal nesting chairs (first revision) May 2010 1 19 IS 4116:1988 Specification for wooden shelving cabinets (adjustable type) (second revision) Sep 2012 2 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 74 2 1 1 Sl No. IS Number/ DOC Number Title 20 IS 4126:1986 Specification for wooden wardrobes (adjustable and nonadjustable type) (first revision) May 2010 2 21 IS 4204:1974 Functional requirements for drafting chairs (first revision) May 2010 1 22 IS 4205:1989 Drafting stools - Specification (second revision) Sep 2012 23 IS 4414:1990 Wooden table tops - Specification (second revision) Sep 2012 2 24 IS 4415:1974 Glossary of terms relating to wooden furniture and fixtures (first revision) Sep 2012 1 25 IS 4837:1990 School furniture, classroom chairs and tables Recommendations (second revision) Sep 2012 26 IS 5391:1992 Adjustable metal chairs for use of typists and operators in telephone exchanges - Specification (second revision) May 2010 27 IS 5416(Part 1):1988 Methods of test for strength and stability of chairs and stools: Part 1 Strength (first revision) Sep 2012 28 IS 5416(Part 2):1988 Method of test for strength and stability of chairs and stools: Part 2 Determination of stability of chairs and stools (first revision) Sep 2012 29 IS 5807(Part 1):1975 Methods of test for clear finishes for wooden furniture: Part 1 Resistance to dry heat (first revision) Sep 2012 30 IS 5807(Part 2):1975 Methods of test for clear finishes for wooden furniture: Part 2 Resistance to wet heat (first revision) Sep 2012 31 IS 5807(Part 3):1971 Methods of test for clear finishes for wooden furniture: Part 3 Resistance to marking by oils and fats Sep 2012 32 IS 5807(Part 4):1975 Methods of test for clear finishes for wooden furniture: Part 4 Resistance to marking by liquids Sep 2012 33 IS 5807(Part 5):1975 Methods of test for clear finishes for wooden furniture: Part 5 Test for low angle glare Sep 2012 34 IS 5807(Part 6):1978 Methods of test for clear finishes for wooden furniture: Part 6 Resistance to mechanical damage Sep 2012 35 IS 5823:1986 Specification for dining tables (first revision) May 2010 2 36 IS 5923:1986 Specification for wooden clothes lockers (first revision) May 2010 2 37 IS 5967(Part 1):1988 Methods of test for strength and stability of tables and trolleys: Part 1 Strength (first revision) Sep 2012 38 IS 5967(Part 2):1988 Methods of test for strength and stability of tables and trolleys : Part 2 Stability (first revision) Sep 2012 39 IS 5974:1986 Reaffirm Date Specification for divans and easy chairs (first revision) May 2010 40 IS 6179:1971 Specification and safety requirements for rigid sided playpens May 2010 41 IS 6184:1971 Dimensions for furniture mirrors Sep 2012 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 75 No. of Amd. 2 3 Sl No. IS Number/ DOC Number Title Reaffirm Date 42 IS 6185:1971 Specification and safety requirements for high chairs May 2010 43 IS 6188:1988 Specification for wooden bedside table (first revision) Sep 2012 44 IS 6189:1985 Specification for metal stationary cupboards (first revision) May 2010 45 IS 6632:1988 Specification for wooden folding chairs (first revision) Sep 2012 2 46 IS 7070:1988 Wooden shelving racks, adjustable and non-adjustable type Specification (first revision) Sep 2012 2 47 IS 7076:1983 Specification for metal book ends (first revision) May 2010 48 IS 7259(Part 1):1988 Specification for wooden beds: Part 1 For use with mattresses (first revision) May 2010 49 IS 7760:1985 Specification for steel glass-front cabinets (first revision) May 2010 50 IS 7761:1983 Specification for steel book cases (first revision) May 2010 51 IS 8126:1993 Specification for composite office tables (first revision) Sep 2012 52 IS 8467:1977 Specification for steel card-index cabinets May 2010 53 IS 8761:1978 Specification for steel folding cots May 2010 54 IS 9236:1993 Specification for metal letter-rests (first revision) Sep 2012 55 IS 9715:1981 Specification for steel visible indexing system cabinets May 2010 56 IS 11525:1986 Specification for wooden chairs for office purposes May 2010 2 57 IS 11679:1986 Specification for wooden tables for office use May 2010 2 58 IS 12674(Part 1):1989 Methods of test for strength and stability of settees and benches: Part 1 Strength Sep 2012 59 IS 12674(Part 2):1989 Methods of test for strength and stability of settees and benches; Part 2 Stability Sep 2012 60 IS 12680:1989 Wooden sofa-cum-bed - Specification Sep 2012 61 IS 13089:1991 / ISO 7171-1988 Furniture - Storage units - Determination of stability May 2010 62 IS 13713:1993 Plastic chairs for general office purposes - Specification Sep 2012 63 IS 13896:1994 Machine operators table and visual display unit (VDU) table Specification Aug 2009 FINALIZED DRAFTS UNDER PRINT 1 DOC.CED 35(7874) Draft Amendment No. 1 to IS 4837:1990 School furniture, Classroom chairs and tables - Recommendations (second revision) * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 76 No. of Amd. 2 2 1 2 CED 36 FIRE SAFETY SCOPE - STANDARDIZATION IN THE FIELD OF FIRE SAFETY; FIRE PRECAUTIONS, FIRE RESISTANCE OF BUILDING MATERIALS, BUILDING COMPONENTS STRUCTURES AND TESTS CONNECTED THEREWITH LIAISON: ISO/TC 92 (P) FIRE SAFETY ISO/TC 92/SC 1 (O) ISO/TC 92/SC 2 (O) ISO/TC 92/SC 3 (O) Sl No. IS Number/ DOC Number Title Reaffirm Date No. of Amd. STANDARDS PUBLISHED 1 IS 1641:2013 Code of practice for fire safety of buildings (general): General principles of fire grading and classification (second revision) 2 IS 1642:2013 Code of practice for fire safety of buildings (general): Details of construction (second revision) (Superseding IS 1645) 3 IS 1643:2013 Code of practice for fire safety of buildings (general): Exposure hazard (second revision) 4 IS 1644:2013 Code of practice for fire safety of buildings (general): Exit requirements and personal hazard (second revision) 5 IS 1646:1997 Code of practice for fire safety of buildings (general): Electrical installations (second revision) Sep 2012 6 IS 2726:1988 Code of practice for fire safety of industrial buildings: Cotton ginning and pressing (including cotton seed delintering) factories (first revision) Sep 2012 7 IS 3034:1993 Code of practice for fire safety of industrial buildings: Electrical generating and distributing stations (second revision) Sep 2012 8 IS 3058:1990 Code of practice for fire safety of industrial buildings: Viscose rayon yarn and/or staple fibre plants (first revision) Nov 2010 9 IS 3079:1990 Code of practice for fire safety of industrial buildings: Cotton textile mills(first revision) Nov 2010 10 IS 3594:1991 Code of practice for fire safety of industrial buildings: General storage and warehousing including cold storages (first revision) Nov 2010 1 11 IS 3595:2002 Code of practice for fire safety of industrial buildings: Coal pulverizers and associated equipments (second revision) Sep 2012 1 12 * IS 3614(Part 1):1966 Specification for fire-check doors: Part 1 Plate metal covered and rolling type Sep 2012 13 IS 3614(Part 2):1992 Specification for metallic and non-metallic fire-check doors Resistance test and performance criteria Sep 2012 14 IS 3808:1979 Method of test for non-combustibility of building materials (first revision) Nov 2010 15 IS 3809:1979 Fire resistance test for structures (first revision) Sep 2012 16 IS 3836:2000 Code of practice for fire safety of industrial buildings - Jute mills (second revision) Nov 2010 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 77 1 Sl No. IS Number/ DOC Number Title Reaffirm Date 17 IS 4226:1988 Sep 2012 18 IS 4886:1991 Code of practice for fire safety of industrial buildings: Aluminium/Magnesium powder factories (first revision) Code of practice for fire safety of industrial buildings: Tea factories (first revision) 19 IS 6329:2000 Code of practice for fire safety of industrial buildings - Saw mills and wood works (first revision) Nov 2010 20 IS 8757:1999 Glossary of terms associated with fire safety (first revision) Jan 2010 21 IS 8758:2013 Recommendations for fire precautionary measures in the construction of temporary structures and pandals (second revision) 22 IS 9109:2000 Code of practice for fire safety of industrial buildings - Paint and varnish factories (first revision) Nov 2010 23 IS 11457(Part 1):1985 Code of practice for fire safety of chemical industries: Part 1 Rubber and plastic Nov 2010 24 IS 11460:1985 Code of practice for fire safety of libraries and archives Nov 2010 25 IS 12349:1988 | ISO 6309 Fire protection-safety signs Sep 2012 26 IS 12407:1988 Graphic symbols for fire protection plans Sep 2012 27 IS 12456:2004 Code of practice for fire protection of electronic data processing installation (first revision) Jan 2010 28 IS 12458:1988 Method for fire resistance test of fire stops Sep 2012 29 IS 12459:1988 Code of practice for fire safety in cable runs Sep 2012 30 IS 12777:1989 Method for classification of flame spread of products Nov 2010 31 IS 13045:1991 Code of practice for fire safety of industrial buildings - Flour mills Nov 2010 32 IS 13694:1993 Code of practice for fire safety in iron and steel industries Sep 2012 1 33 IS 13716:1993 Code of practice for fire safety of hotels Sep 2012 1 34 IS 14435:2013 Fire safety in educational institutions्- Code of practice्(first्revision) 35 IS 14689:1999 Code of practice for fire safety in industrial buildings (printing and publishing industry) Jan 2010 36 IS 14850:2000 Code of practice for fire safety of museums Nov 2010 37 IS 15381:2003 Specification for fire blanket Sept 2013 38 IS 15394:2003 Code of practice for fire safety in petroleum refineries and fertilizer plants Sept 2013 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS Nov 2010 ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 78 No. of Amd. 1 1 1 FINALISED DRAFTS UNDER PRINT 1 DOC.CED 36(7667) First revision of IS 11460 2 DOC.CED 36(7669) First revision of IS 13716 3 DOC.CED 36(7671) First revision of IS 14850 4 DOC.CED 36(7810) Draft Indian Standard code of practice for fire safety of buildings (general): Electrical installations (third revision of IS 1646) 5 DOC. CED36(7925) Fire Resistance Tests – Elements of Building Construction Part 1 General Requirements (Adoption of ISO 834-1:1999) 6 DOC. CED36(7926) Fire Resistance Tests – Elements of Building Construction Part 4 Specific Requirements for Load Bearing Vertical Separating Elements (Adoption of ISO 834-4:2000) 7 DOC. CED36(7927) Fire Resistance Tests – Elements of Building Construction Part 5 Specific Requirements for Load Bearing Horizontal Separating Elements (Adoption of ISO 834-5:2000) 8 DOC. CED36(7928) Fire Resistance Tests – Elements of Building Construction Part 6 Specific Requirements for beams (Adoption of ISO 834-6:2000) DRAFT STANDARDS FINALIZED BUT NOT YET UNDER PRINT 1 DOC. CED36(7929) Fire Resistance Tests – Elements of Building Construction Part 7 Specific Requirements for columns (Adoption of ISO 834-7:2000) 2 DOC. CED36(7930) Fire Resistance Tests – Elements of Building Construction Part 8 Specific Requirements for Non- Load Bearing Verticals Separating Elements (Adoption of ISO 834-8:2002) 3 DOC. CED36(7931) Fire Resistance Tests – Elements of Building Construction Part 9 Specific Requirements for Non- Load Bearing Ceiling Elements (Adoption of ISO 834-9:2003) 4 DOC. CED36(7932) Fire Resistance Tests – Elements of Building Construction – Glazed Elements (Adoption of ISO 3009:2003) 5 DOC. CED36(7933) Guidelines for Assessing the Fire Threat to People (Adoption of ISO 19706:2011) * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 79 CED 37 STRUCTURAL SAFETY SCOPE - STANDARDIZATION IN THE FIELD OF STRUCTURAL SAFETY INCLUDING LOADING STANDARDS LIAISON: ISO/TC 98 (O) BASIS OF DESIGN OF STRUCTURES ISO/TC 98/SC 1 TERMINOLOGY AND SYMBOLS ISO/TC 98/SC 2 RELIABILITY OF STRUCTURES ISO/TC 98/SC 3 LOADS, FORCES AND OTHER ACTIONS Sl No. IS Number/ DOC Number Title Reaffirm Date No. of Amd. STANDARDS PUBLISHED 1 IS 875(Part 1):1987 Code of practice for design loads (other than earthquake)for buildings and structures Part 1 Dead loads - Unit weights of building material and stored materials (second revision) (Incorporating IS:1911-1967) May 2013 1 2 IS 875(Part 2):1987 Code of practice for design loads (other than earthquake) for buildings and structures: Part 2 Imposed loads (second revision) May 2013 1 3 IS 875(Part 3):1987 Code of practice for design loads (other than earthquake) for buildings and structures: Part 3 Wind loads (second revision) May 2013 3 4 IS 875(Part 4):1987 Code of practice for design loads (other than earthquake) for buildings and structures Part 4 Snow loads (second revision) May 2013 5 IS 875(Part 5):1987 Code of practice for design loads (other than earthquake) for buildings and structures Part 5 Special loads and load combinations (second revision) May 2013 6 SP 64(S&T): 2001 Explanatory Handbook on Indian Standard Code of practice for Design Loads (Other than Earthquake) for Buildings and Structures: Part 3 Wind Loads [IS 875(Part 3):1987] DRAFT STANDARDS UNDER PRINT 1 DOC.CED 37(7792) Draft Indian Standard Code of practice for design loads (other than earthquake) for buildings and structures: Part 3 Wind loads [Third Revision of IS 875 (Part 3)] * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 80 1 CED 38 SPECIAL STRUCTURES SCOPE - STANDARDIZATION IN THE FIELD OF DESIGN OF SPECIAL STRUCTURES SUCH AS CHIMNEYS, BINS AND SILOS, SHELL STRUCTURES, OVERHEAD WATER TANKS, COOLING TOWERS, SPACE STRUCTURES, COMPOSITE CONSTRUCTION, ETC, CONSISTING OF REINFORCED AND PRESTRESSED CONCRETE, HANDBOOKS RELATING TO SPECIAL STRUCTURES Sl No. IS Number/ DOC Number Title Reaffirm Date No. of Amd. STANDARDS PUBLISHED 1 IS 2210:1988 Criteria for design of reinforced concrete shell structures and folded plates (first revision) Oct 2012 2 IS 3935:1966 Code of practice for composite construction Oct 2012 3 IS 4090:1967 Criteria for design of reinforced concrete arches Oct 2012 4 IS 4995(Part 1):1974 Criteria for design of reinforced concrete bins for storage of granular and powdery materials: Part 1 General requirements and assessment of bin loads (first revision) Oct 2012 1 5 IS 4995(Part 2):1974 Criteria for design of reinforced concrete bins for storage of granular and powdery materials: Part 2 Design criteria (first revision) Oct 2012 1 6 *IS 4998(Part 1):1992 Criteria for design of reinforced concrete chimneys: Part 1 Assessment of loads (second revision) Oct 2012 7 IS 11384:1985 Code of practice for composite construction in structural steel and concrete Oct 2012 8 IS 11504:1985 Criteria for structural design of reinforced concrete natural draught cooling towers Oct 2012 9 IS 11682:1985 Criteria for design of RCC staging for overhead water tanks Oct 2012 10 SP 43(S&T): 1987 Handbook on structures with reinforced concrete portal frames (without cranes) DRAFT STANDARD COMPLETED WIDE CIRCULATION 1. CED 38(7892) Third revision of IS 4998 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 81 1 CED 39 EARTHQUAKE ENGINEERING SCOPE - STANDARDIZATION IN THE FIELD OF DESIGN AND CONSTRUCTION OF EARTHQUAKE RESISTANT STRUCTURES AND IN THE FIELD OF INSTRUMENTS AND TESTS CONNECTED THEREWITH LIAISON; ISO/TC 98 (O) BASIS FOR DESIGN OF STRUCTURES Sl No. IS Number/ DOC Number Title Reaffirm Date No. of Amd. STANDARDS PUBLISHED 1 * IS 1893:1984 Criteria for earthquake resistant design of structures (fourth revision) Jul 2013 2 * IS 1893(Part 1):2002 Criteria for earthquake resistant design of structures: Part 1 General Provisions and buildings (fifth revision) Sep 2012 3 * IS 1893(Part 4):2005 Criteria for earthquake resistant design of structures: Part 4 Industrial structures including stack-like structure Jan 2010 4 IS 4326:2013 Code of practice for earthquake resistant design and construction of buildings (third revision) 5 IS 4967:1968 Recommendations for seismic instrumentation for river valley projects Nov 2010 6 IS 4991:1968 Criteria for blast resistant design of structures for explosions above ground Jul 2013 7 IS 6922:1973 Criteria for safety and design of structures subject to underground blasts Jul 2013 8 IS 13827:1993 Improving earthquake resistance of earthen buildings - Jul 2013 2 9 IS 13828:1993 Improving earthquake resistance of low strength masonry buildings - Guidelines Jul 2013 3 10 * IS 13920:1993 Ductile detailing of reinforced concrete structures subjected to seismic forces- Code of practice Jul 2013 2 11 IS 13935:2009 Guidelines for evaluation, repair and seismic strengthening of masonry buildings (first revision) 12 IS 15988:2013 Seismic Evaluation and Strengthening of Existing Reinforced Concrete Buildings - Guidelines. FINALISED DRAFTS UNDER PRINT 1 DOC.CED 39(7231) Criteria for earthquake resistant design of structures: Part 2 Liquid retaining tank 2 DOC.CED 39(7739) Draft Indian Standards Criteria for earthquake resistant design of structures: Part 3 Bridges and retaining walls * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 82 2 DRAFT STANDARDS FINALIZED BUT NOT YET UNDER PRINT 1 DOC.CED 39(7807) Draft Indian Standard Criteria for earthquake resistant design of structures: Part 4 Industrial structures including stack like structure [First Revision of IS 1893 (Part 4)] DRAFT STANDARDS COMPLETED WIDE CIRCULATION 1 DOC.CED 39(7545) Draft Indian Standard Criteria for Tsunami resistance design of structures DRAFT STANDARDS UNDER WIDE CIRCULATION 1 DOC.CED 39(7941) First Revision of IS 13920 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 83 CED 41 WATERPROOFING AND DAMP-PROOFING SCOPE - STANDARDIZATION IN THE FIELD OF WATERPROOFING AND DAMPPROOFING MAINLY WITH REFERENCE TO GENERAL BUILDING CONSTRUCTION INCLUDING SPECIFICATION FOR MATERIALS, CODE OF PRACTICE AND METHODS OF TESTS STANDARDS PUBLISHED Sl No. IS Number/ DOC Number Title Reaffirm Date 1 IS 1322:1993 Specification for bitumen felts for water proofing and dampproofing (fourth revision) Jan 2013 2 IS 1346:1991 Code of practice for waterproofing of roofs with bitumen felts (third revision) Dec 2010 3 IS 1580:1991 Specification for bituminous compounds for water-proofing and caulking purposes (second revision) Dec 2010 4 IS 1609:1991 Code of practice for damp-proofing treatment using bitumen felts (third revision) Dec 2010 5 IS 3036:1992 Code of practice for laying lime concrete for a waterproofed roof finish (second revision) Jan 2013 6 IS 3037:1986 Specification for bitumen mastic for use in water-proofing of roofs (first revision) Dec 2010 7 IS 3067:1988 Code of practice for general design details and preparatory work for damp-proofing and water-proofing of buildings (first revision) Apr 2010 8 IS 3384:1986 Specification for bitumen primer for use in waterproofing and damp-proofing (first revision) Dec 2010 9 IS 4365:1967 Code of practice for application of bitumen mastic for waterproofing of roofs Dec 2010 10 IS 4911:1986 Glossary of terms relating to bituminous waterproofing and damp-proofing of buildings (first revision) Apr 2011 11 IS 5871:1987 Specification for bitumen mastic for tanking and dampproofing (first revision) Dec 2010 12 IS 6494:1988 Code of practice for water-proofing of underground water reservoirs and swimming pools (first revision) Dec 2010 13 IS 7193:1994 Glass fibre base bitumen felts - Specification (first revision) Jan 2014 14 IS 7198:1974 Code of practice for damp-proofing using bitumen mastic Dec 2010 15 IS 7290:1979 Recommendations for use of polyethylene film for waterproofing of roofs (first revision) Dec 2010 16 IS 9918:1981 Code of practice for in-situ waterproofing and damp-proofing treatment with glass fibre tissue reinforced bitumen Apr 2011 17 IS 12027:1987 Specification for silicone-based water repellents Jan 2013 18 IS 12054:1987 Code of practice for application of silicone based water repellents Apr 2011 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 84 No. of Amd. 2 1 1 1 1 Sl No. IS Number/ DOC Number Title 19 IS 13182:1991 Waterproofing and damp-proofing of wet areas in building Recommendations Apr 2011 20 IS 13435(Part 1):1992 Acrylic based polymer waterproofinng materials - Methods of test: Part 1 Determination of solid content Jan 2013 21 IS 13435(Part 2):1992 Acrylic based polymer waterproofing materials - Methods of test: Part 2 Determination of coarse particles Jan 2013 22 IS 13435(Part 3):1992 Acrylic based polymer waterproofing material - Methods of test Part 3 Determination of capillary water take-up Jan 2013 23 IS 13435(Part 4):1992 Acrylic based polymer waterproofing material - Methods of test Part 4 Determination of pH value Jan 2013 24 IS 13826(Part 1):1993 Bitumen based felt - Methods of test: Part 1 Breaking strength Jan 2013 1 25 IS 13826(Part 2):1993 Bitumen based felt - Methods of test Part 2 Pliability test Jan 2013 1 26 IS 13826(Part 3):1993 Bitumen based felt - Methods of test; Part 3 Storage sticking Jan 2013 27 IS 13826(Part 4):1994 Reaffirm Date Bitumen based felt - Methods of test: Part 4 Pressure head test Jan 2013 28 IS 13826(Part 5):1994 Bitumen based felt - Methods of test; Part 5 Heat resistance Jan 2013 29 IS 13826(Part 6):1993 Bitumen based felt - Methods of test; Part 6 Water absorption Jan 2013 30 IS 13826(Part 7):1993 Bitumen based felt - Methods of test: Part 7 Determination of binder content Jan 2013 31 IS 14695:1999 Glass fibre base coal tar pitch outer wrap - Specification Jan 2014 FINALISED DRAFTS UNDER PRINT 1 DOC.CED 41(7718) Draft Indian Standard Glass Fibre Based Bitumen Felts Specification (Second Revision of IS 7193) * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 85 No. of Amd. 1 1 1 SCOPE - CED 43 SOIL AND FOUNDATION ENGINEERING FORMULATION OF INDIAN STANDARDS IN THE FIELD OF SOIL AND SOIL ENGINEERING COVERING: I) SUB-SURFACE EXPLORATION (OTHER THAN RIVER VALLEY PROJECTS); II) SOIL SAMPLING AND TESTING INCLUDING STABILZED SOILS; AND III) SOIL CLASSIFICATION FOR ENGINEERING PURPOSES; IV) LOAD BEARING CAPACITIES OF SOILS; V) GROUND IMPROVEMENT TECHNIQUES. STANDARDIZATION IN THE FIELD OF FOUNDATION ENGINEERING IN PARTICULAR DESIGN REQUIREMENTS AND CONSTRUCTION PRACTICES FOR VARIOUS TYPES OF FOUNDATIONS AND SPECIAL LOAD TESTS ON FOUNDATIONS LIAISON: ISO/TC 182 (O) GEOTECHNICS ISO/TC 182/SC 1 (O) ISO/TC 182/SC 3 (O) Sl No. IS Number/ DOC Number Title Reaffirm Date No. of Amd. STANDARDS PUBLISHED 1 IS 1080:1985 Code of practice for design and construction of shallow foundations in soils (other than raft, ring and shell) (second revision) Dec 2011 2 IS 1498:1970 Classification and identification of soils for general engineering purposes (first revision) Dec 2011 3 IS 1888:1982 Method of load test on soils (second revision) Dec 2011 4 IS 1892:1979 Code of practice for subsurface investigation for foundations (first revision) Dec 2011 5 IS 1904:1986 Code of practice for design and construction of foundations in soils: General requirements (third revision) May 2010 6 IS 2131:1981 Method of standard penetration test for soils (first revision) Dec 2011 7 IS 2132:1986 Code of practice for thin walled tube sampling of soils (second revision) Dec 2011 8 IS 2720(Part 1):1983 Methods of test for soils: Part 1 Preparation of dry soil samples for various tests (second revision) May 2010 9 IS 2720(Part 2):1973 Methods of test for soils: Part 2 Determination of water content (second revision) May 2010 10 IS 2720(Part 3/Sec 1):1980 Methods of test for soils: Part 3 Determination of specific gravity, Section 1 Fine grained soils (first revision) Dec 2011 11 IS 2720(Part 3/Sec 2):1980 Methods of test for soils: Part 3 Determination of specific gravity, Section 2 Fine, medium and coarse grained soils (first revision) Dec 2011 12 IS 2720(Part 4):1985 Methods of test for soils: Part 4 Grain size analysis (second revision) May 2010 13 IS 2720(Part 5):1985 Methods of test for soils: Part 5 Determination of liquid and plastic limit (second revision) May 2010 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 86 2 1 Sl No. IS Number/ DOC Number Title 14 IS 2720(Part 6):1972 Methods of test for soils: Part 6 Determination of shrinkage factors (first revision) Dec 2011 1 15 IS 2720(Part 7):1980 Methods of test for soils: Part 7 Determination of water contentdry density relation using light compaction (second revision) Dec 2011 2 16 IS 2720(Part 8):1983 Methods of test for soils: Part 8 Determination of water contentdry density relation using heavy compaction (second revision) May 2010 17 IS 2720(Part 9):1992 Methods of test for soils: Part 9 Determination of dry densitymoisture content relation by constant mass of soil method (first revision) Dec 2011 18 IS 2720(Part 10):1991 Methods of test for soils: Part 10 Determination of unconfined compressive strength (second revision) May 2010 19 IS 2720(Part 11):1993 Methods of test for soils: Part 11 Determination of the shear strength parameters of a specimen tested in unconsolidated undrained triaxial compression without the measurement of pore water pressure (first revision) Dec 2011 20 IS 2720(Part 12):1981 Methods of test for soils: Part 12 Determination of shear strength parameters of soil from consolidated undrained triaxial compression test with measurement of pore water pressure (first revision) Dec 2011 21 IS 2720(Part 13):1986 Methods of test for soils: Part 13 Direct shear test (second revision) Dec 2011 22 IS 2720(Part 14):1983 Methods of test for soils: Part 14 Determination of density index (relative density) of cohesionless soils (first revision) May 2010 23 IS 2720(Part 15):1986 Methods of test for soils: Part 15 Determination of consolidation properties (first revision) Dec 2011 Methods of test for soils: Part 16 Laboratory determination of CBR (second revision) Dec 2011 24 IS 2720(Part 16):1987 Reaffirm Date No. of Amd. 1 25 IS 2720(Part 17):1986 Methods of test for soils: Part 17 Laboratory determination of permeability (first revision) Dec 2011 26 IS 2720(Part 18):1992 Methods of test for soils: Part 18 Determination of field moisture equivalent (first revision) Dec 2011 27 IS 2720(Part 19):1992 Methods of test for soils: Part 19 Determination of centrifuge moisture equivalent (first revision) Dec 2011 28 IS 2720(Part 20):1992 Methods of test for soils: Part 20 Determination of linear shrinkage (first revision) Dec 2011 29 IS 2720(Part 21):1977 Methods of test for soils: Part 21 Determination of total soluble solids (first revision) May 2010 1 30 IS 2720(Part 22):1972 Methods of test for soils: Part 22 Determination of organic matter (first revision) May 2010 1 31 IS 2720(Part 23):1976 Methods of test for soils: Part 23 Determination of calcium carbonate (first revision) May 2010 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 87 Sl No. IS Number/ DOC Number Title 32 IS 2720(Part 24):1976 Methods of test for soils: Part 24 Determination of cation exchange capacity (first revision) May 2010 33 IS 2720(Part 25):1982 Methods of test for soils: Part 25 Determination of silica sesquioxide ratio (first revision) May 2010 34 IS 2720(Part 26):1987 Methods of test for soils: Part 26 Determination of pH value (second revision) Dec 2011 35 IS 2720(Part 27):1977 Methods of test for soils: Part 27 Determination of total soluble sulphates (first revision) May 2010 36 IS 2720(Part 28):1974 Methods of test for soils: Part 28 Determination of dry density of soils, in-place, by the sand replacement method (first revision) May 2010 37 IS 2720(Part 29):1975 Methods of test for soils: Part 29 Determination of dry density of soils in-place, by the core-cutter method (first revision) May 2010 Methods of test for soils: Part 30 Laboratory vane shear test (first revision) Dec 2011 38 IS 2720(Part 30):1980 Reaffirm Date No. of Amd. 1 1 1 39 IS 2720(Part 31):1990 Methods of test for soils: Part 31 Field determination of California bearing ratio (first revision) May 2010 40 IS 2720(Part 33):1971 Methods of test for soils: Part 33 Determination of the density in place by the ring and water replacement method May 2010 1 41 IS 2720(Part 34):1972 Methods of test for soils: Part 34 Determination of density of soil in place by rubber balloon method May 2010 1 42 IS 2720(Part 35):1974 Methods of test for soils: Part 35 Measurement of negative pore water pressure May 2010 43 IS 2720(Part 36):1987 Methods of test for soils: Part 36 Laboratory determination of permeability of granular soils (constant head) (first revision) Dec 2011 44 IS 2720(Part 37):1976 Methods of test for soils: Part 37 Determination of sand equivalent value of soils and fine aggregates Dec 2011 45 IS 2720(Part 38):1976 Methods of test for soils: Part 38 Compaction control test (Hilf method) Dec 2011 46 IS 2720(Part 39/Sec 1):1977 Methods of test for soils: Part 39 Direct shear test for soils containing gravel, Section 1 Laboratory test Dec 2011 47 IS 2720(Part 39/Sec 2):1979 Methods of test for soils: Part 39 Direct shear test for soils containing gravel, Section 2 In-situ shear test Dec 2011 48 IS 2720(Part 40):1977 Methods of test for soils: Part 40 Determination of free swell index of soils Dec 2011 49 IS 2720(Part 41):1977 Methods of test for soils: Part 41 Measurement of swelling pressure of soils Dec 2011 50 IS 2809:1972 Glossary of terms and symbols relating to soil engineering (first revision) May 2010 51 IS 2810:1979 Glossary of terms relating to soil dynamics (first revision) Dec 2011 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 88 2 Sl No. IS Number/ DOC Number Title 52 Design and construction of pile foundations- Code of practice: Part 1 Concrete piles, Section 1 Driven cast in-situ concrete piles (second revision) IS 2911(Part 1/Sec 1):2010 Reaffirm Date No. of Amd. 53 IS 2911(Part 1/Sec 2):2010 Design and construction of pile foundations- Code of practice: Part 1 Concrete piles, Section 2 Bored cast-in-situ concrete piles (second revision) 54 IS 2911(Part 1/Sec 3):2010 Design and construction of pile foundations- Code of practice: Part 1 Concrete piles, Section 3 Driven precast concrete piles (second revision) 55 IS 2911(Part 1/Sec 4):2010 Design and construction of pile foundations- Code of practice: Part 1 Concrete piles, Section 4 Precast concrete piles in prebored holes (first revision) 56 IS 2911(Part 2):1980 Code of practice for design and construction of pile foundations: Part 2 Timber piles (first revision) May 2010 1 57 IS 2911(Part 3):1980 Code of practice for design and construction of pile foundations: Part 3 Under reamed piles (first revision) May 2010 3 58 IS 2911(Part 4):2013 Design and construction of pile foundations - Code of practice: Part 4 Load test on piles (second revision) 59 IS 2950(Part 1):1981 Code of practice for design and construction of raft foundations: Part 1 Design (second revision) Nov 2013 1 60 IS 2974(Part 1):1982 Code of practice for design and construction of machine foundations: Part 1 Foundations for reciprocating type machines (second revision) Nov 2013 1 61 IS 2974(Part 2):1980 Code of practice for design and construction of machine foundations: Part 2 Foundations for impact type machines (hammer foundations) (first revision) Nov 2013 1 62 IS 2974(Part 3):1992 Code of practice for design and construction of machine foundations: Part 3 Foundations for rotary type machines (medium and high frequency) (second revision) May 2010 63 IS 2974(Part 4):1979 Code of practice for design and construction of machine foundations: Part 4 Foundations for rotary type machines of low frequency (first revision) May 2010 64 IS 2974(Part 5):1987 Code of practice for design and construction of machine foundations: Part 5 Foundations for impact machines other than hammer (forging and stamping press, pig breaker, drop crusher and jolter) (first revision) Nov 2013 65 IS 4091:1979 Code of practice for design and construction of foundations for transmission line towers and poles (first revision) May 2010 Methods of test for stabilized soils: Part 1 Method of sampling and preparation of stabilized soils for testing May 2010 1 Methods of test for stabilized soils: Part 2 Determination of moisture content of stabilized soil mixtures May 2010 1 66 67 IS 4332(Part 1):1967 IS 4332(Part 2):1967 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS 2 ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 89 1 Sl No. IS Number/ DOC Number Title 68 Methods of test for stabilized soils: Part 3 Test for determination of moisture content-dry density relation for IS 4332(Part 3):1967 Reaffirm Date No. of Amd. May 2010 1 1 stablized soil mixtures 69 IS 4332(Part 4):1968 Methods of test for stabilized soils: Part 4 Wetting and drying and freezing and thawing tests for compacted soil-cement mixtures May 2010 70 IS 4332(Part 5):1970 Methods of test for stabilized soils: Part 5 Determination of unconfined compressive strength of stabilized soils May 2010 71 IS 4332(Part 6):1972 Methods of test for stabilized soils: Part 6 Flexural strength of soil - cement using simple beam with third-point loading May 2010 1 72 IS 4332(Part 7):1973 Methods of test for stabilized soils: Part 7 Determination of cement content of cement stabilized soils May 2010 1 73 IS 4332(Part 8):1969 Methods of test for stabilized soils: Part 8 Determination of lime content of lime stabilized soils May 2010 1 74 IS 4332(Part 9):1970 Methods of test for stabilized soils: Part 9 Determination of the bituminous stabilizer content of bitumen and tar stabilized May 2010 1 75 IS 4332(Part 10):1969 Methods of test for stabilized soils: Part 10 Test for soil/bituminous mixtures May 2010 1 76 IS 4434:1978 Code of practice for in-situ vane shear test for soils (first revision) Dec 2011 77 IS 4968(Part 1):1976 Method for subsurface sounding for soils: Part 1 Dynamic method using 50 mm cone without bentonite slurry (first revision) Dec 2011 1 78 IS 4968(Part 2):1976 Method for subsurface sounding for soils: Part 2 Dynamic method using cone and bentonite slurry (first revision) Dec 2011 1 79 IS 4968(Part 3):1976 Method for subsurface sounding for soils: Part 3 Static cone penetration test (first revision) Dec 2011 Determination of dynamic properties of soil - Method of test (second revision) May 2010 1 80 IS 5249:1992 81 IS 6403:1981 Code of practice for determination of bearing capacity of shallow foundations (first revision) Dec 2011 1 82 IS 8009(Part 1):1976 Code of practice for calculation of settlements of foundations: Part 1 Shallow foundations subjected to symmetrical static vertical loads Nov 2013 2 83 IS 8009(Part 2):1980 Code of practice for calculation of settlement of foundations: Part 2 Deep foundations subjected to symmetrical static May 2010 1 84 IS 8763:1978 Guide for undisturbed sampling of sands Dec 2011 85 IS 9198:1979 Specification for compaction rammer for soil testing Dec 2011 86 IS 9214:1979 Method for determination of modulus of sub-grade reaction (k-value) of soils in field 87 IS 9259:1979 Specification for liquid limit apparatus for soils * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS Dec 2011 Dec 2011 ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 90 1 1 1 Sl No. IS Number/ DOC Number Title Reaffirm Date 88 IS 9456:1980 Code of practice for design and construction of conical and hyperbolic paraboloidal types of shell foundations Nov 2013 1 89 IS 9556:1980 Code of practice for design and construction of diaphragm walls Nov 2013 1 90 IS 9640:1980 Specification for split spoon sampler Dec 2011 2 91 IS 9669:1980 Specification for CBR moulds and its accessories Dec 2011 2 92 IS 9716:1981 Guide for lateral dynamic load test on piles Nov 2013 93 IS 9759:1981 Guidelines for dewatering during construction Nov 2013 94 IS 10042:1981 Code of practice for site investigations for foundation in gravel boulder deposit Dec 2011 95 IS 10074:1982 Specification for compaction mould assembly for light and heavy compaction test for soils May 2010 96 IS 10077:1982 Specification for equipment for determination of shrinkage May 2010 97 IS 10108:1982 Code of practice for sampling of soils by thin wall sampler with stationary piston May 2010 98 IS 10270:1982 Guidelines for design and construction of prestressed rock anchors Nov 2013 99 IS 10379:1982 Code of practice for field control of moisture and compaction of soils of embankment and subgrade May 2010 100 IS 10442:1983 Specification for earth augers (spiral type) May 2010 101 IS 10589:1983 Specification for equipment for subsurface sounding of soils May 2010 102 IS 10837:1984 Specification for moulds and accessories for determination of density index (relative density) of cohesionless soils May 2010 103 IS 11089:1984 Code of practice for design and construction of ring foundation Dec 2011 104 IS 11196:1985 Specification for equipment for determination of liquid limit of soils cone penetration method May 2010 105 IS 11209:1985 Specification for mould assembly for determination of permeability of soils May 2010 106 IS 11229:1985 Specification for shear box for testing of soils May 2010 107 IS 11233:1985 Code of practice for design and construction of radar antenna, microwave and TV tower foundations Dec 2011 108 IS 11550:1985 Code of practice for field instrumentation of swelling pressure in expansive soils Dec 2011 109 IS 11593:1986 Specification for shear box (large) for testing of soils May 2010 110 IS 11594:1985 Specification for mild steel thin walled sampling tubes and sampler heads May 2010 111 IS 11629:1986 Code of practice for installation and operation of single point hydraulic over-flow setting gauge Dec 2011 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 91 No. of Amd. 1 2 1 Sl No. IS Number/ DOC Number Title 112 IS 12023:1987 Code of practice for field monitoring of movement of structures using tape extensometer May 2010 113 IS 12070:1987 Code of practice for design and construction of shallow foundations on rock Jul 2010 114 IS 12175:1987 Specification for rapid moisture meter for rapid determination of water content for soil Dec 2011 115 IS 12208:1987 Method for measurement of earth pressure by hydraulic pressure cell May 2010 116 IS 12287:1988 Specification for consolidometer for determination of consolidation properties May 2010 117 IS 12979:1990 Mould for determination of linear shrinkage - Specification May 2010 118 IS 13094:1992 Selection of ground improvement techniques for foundation in weak soils - Guidelines Dec 2011 119 IS 13301:1992 Vibration isolation for machine foundations - Guidelines Dec 2011 120 IS 13468:1992 Apparatus for determination of dry density of soil by core cutter method - Specification Dec 2011 121 IS 14593:1998 Design and construction of bored cast-in-situ piles founded on rocks - Guidelines June 2013 Non-destructive integrity testing of piles (NDT) - Guidelines May 2010 122 IS 14893:2001 Reaffirm Date 123 IS 15284(Part 1):2003 Design and construction for ground improvement - Guidelines: Part 1 Stone columns June 2013 124 IS 15284(Part 2):2004 Design and construction for ground improvement - Guidelines: Part 2 Preconsolidation using vertical drains Aug 2009 125 SP 36(Part 1): 1987 Compendium of Indian standards on soil engineering: Part 1 Laboratory testing of soils for civil engineering purposes 126 SP 36(Part 2): 1988 Compendium of Indian standards on soil engineering: Part 2 Field testing of soils for civil engineering purposes FINALISED DRAFTS UNDER PRINT 1 DOC.CED 43(7854) Draft Amendment No. 4 to IS 2911 (Part 3):1980 Code of practice for design and construction of pile foundations: Part 3 Under reamed piles (first revision) 2 DOC.CED 43(7855) Draft Amendment No. 3 to IS 8009 (Part 1):1976 Code of practice for calculation of settlements of foundations: Part 1 Shallow foundations subjected to symmetrical static vertical 3 DOC.CED 43(7820) Draft Amendment No. 1 to IS 11196:1985 Specification for equipment for determination of liquid limit of soils cone penetration method DRAFT STANDARDS ISSUED IN WIDE CIRCULATION 1 DOC.CED 43(7916) Draft Amendment No. 2 to IS 6403:1981 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 92 No. of Amd. 1 1 CED 44 METHODS OF MEASUREMENT OF WORKS OF CIVIL ENGINEERING (EXCLUDING WATER RESOURCES DEVELOPMENT DIVISION) SCOPE - STANDARDIZATION IN THE FIELD OF MEASUREMENT OF CIVIL ENGINEERING WORKS (EXCLUDING THOSE RELATING TO WATER RESOURCES DEVELOPMENT) Sl No. IS Number/ DOC Number Title Reaffirm Date No. of Amd. STANDARDS PUBLISHED 1 IS 1200(Part 1):1992 Methods of measurement of building and civil engineering works: Part 1 Earthwork (fourth revision) Sep 2012 1 2 IS 1200(Part 2):1974 Methods of measurement of building and civil engineering works: Part 2 Concrete works (third revision) Sep 2012 2 3 IS 1200(Part 3):1976 Methods of measurement of building and civil engineering works: Part 3 Brickwork(third revision) Sep 2012 4 IS 1200(Part 4):1976 Methods of measurement of building and civil engineering works: Part 4 Stone masonry (third revision) Sep 2012 5 IS 1200(Part 5):2013 Methods of measurement of building and civil engineering works: part 5 Form work (fourth revision) 6 IS 1200(Part 6):1974 Methods of measurement of building and civil engineering works: Part 6 Refractory work (second revision) 7 IS 1200(Part 7):2013 Methods of measurement of building and civil engineering works: Part 7 Hardware (third revision) 8 IS 1200(Part 8):1993 9 Sep 2012 2 Methods of measurement of building and civil engineering works: Part 8 Steel work and iron work (fourth revision) Sep 2012 1 IS 1200(Part 9):1973 Methods of measurement of building and civil engineering works: Part 9 Roof covering (including cladding) (second revision) Sep 2012 1 10 IS 1200(Part 10):2013 Methods of measurement of building and civil engineering works: part 10 Ceiling and linings (third revision) 11 IS 1200(Part 11):2013 Methods of measurement of building and civil engineering works: Part 11 Paving, floor finishes, dado and skirting (fourth revision) 12 IS 1200(Part 12):1976 Methods of measurement of building and civil engineering works: Part 12 plastering and pointing (third revision) Sep 2012 13 IS 1200(Part 13):1994 Methods of measurement of building and civil engineering works: Part 13 Whitewashing, colour washing, distempering and painting of building surfaces (fifth revision) Sep 2012 2 14 IS 1200(Part 14):1984 Methods of measurement of building and civil engineering works: Part 14 Glazing (third revision) Sep 2012 1 15 IS 1200(Part 15):1987 Method of measurement of building and civil engineering works: Part 15 painting, polishing, varnishing etc (fourth revision) Sep 2012 1 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 93 Sl No. IS Number/ DOC Number Title Reaffirm Date 16 IS 1200(Part 16):1979 Method of measurement of building and civil engineering works: Part 16 Laying of water and sewer lines including appurtenant items (third revision) Sep 2012 17 IS 1200(Part 18):1974 Method of measurement of building and civil engineering works: Part 18 Demolition and dismantling (third revision) Sep 2012 18 IS 1200(Part 19):1981 Method of measurement of building and civil engineering works: Parts 19 Water supply, plumbing and drains (third revision) Sep 2012 19 IS 1200(Part 20):1981 Method of measurement of building and civil engineering works: Part 20 Laying of gas and oil pipelines (third revision) Sep 2012 20 IS 1200(Part 21):1973 Method of measurement of building and civil engineering works: Part 21 Wood-work and joinery (second revision) Sep 2012 21 IS 1200(Part 22):1982 Method of measurement of building and civil engineering works: Part 22 Materials Sep 2012 22 IS 1200(Part 23):1988 Method of measurement of building and civil engineering works: Part 23 Piling (fourth revision) Sep 2012 23 IS 1200(Part 24):1983 Method of measurement of building and civil engineering works: Part 24 Well foundations (third revision) Sep 2012 1 24 IS 1200(Part 25):1971 Method of measurement of building and civil engineering works: Part 25 Tunneling (second revision) Sep 2012 4 25 IS 1200(Part 26):1987 Method of measurement of building and civil engineering works: Part 26 Acid resistant lining Sep 2012 26 IS 1200(Part 27):2013 Method of measurement of building and civil engineering works: Part 27 Earth work done by mechanical appliances (first revision) 27 IS 1200(Part 28):1992 Methods of measurement of building and civil engineering works: Part 28 Sound insulation work Sep 2012 28 IS 3861:2002 Method of measurement of plinth, carpet and rentable areas of buildings (second revision) Sep 2012 29 SP 27: 1987 Handbook on method of measurement of buildings works (first revision) Oct 2003 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 94 No. of Amd. 1 CED 46 SCOPE - NATIONAL BUILDING CODE Work relating to National Building Code of India Sl No. IS Number/ DOC Number Title Reaffirm Date STANDARDS PUBLISHED 1 SP 7: 2005 National Building Code of India 2005: Part 0 Integrated Approach - Prerequisite for applying provisions of the Code 2 SP 7(Part 1): 2005 National Building Code of India 2005: Part 1 Definitions 3 SP 7(Part 2): 2005 National Building Code of India 2005: Part 2 Administration 4 SP 7(Part 3): 2005 National Building Code of India 2005: Part 3 Development control rules and general building requirements 5 SP 7(Part 4): 2005 National Building Code of India 2005: Part 4 Fire and life safety 6 SP 7(Part 5): 2005 National Building Code of India 2005: Part 5 Building materials 7 SP 7(Part 6): 2005 National Building Code of India 2005: Part 6 Structural design Section 1 Loads, forces and effects Section 2 Soils and foundations Section 3 Timber and bamboo 3A Timber 3B Bamboo Section 4 Masonry Section 5 Concrete 5A Plain and reinforced concrete 5B Prestressed concrete Section 6 Steel Section 7 Prefabrication, systems building and mixed/composite construction 7A Prefabricated concrete 7B Systems buildings and mixed/composite construction 8 SP 7(Part 7): 2005 National Building Code of India 2005: Part 7 Constructional practices and safety 9 SP 7(Part 8): 2005 National Building Code of India 2005: Part 8 Building services Section 1 Lighting and ventilation Section 2 Electrical and allied installations Section 3 Air conditioning, heating and mechanical ventilation Section 4 Acoustics, sound insulations and noise control Section 5 Installation of lifts and escalators 10 SP 7(Part 9): 2005 National Building Code of India 2005: Part 9 Plumbing services Section 1 Water supply, drainage and sanitation (including solid waste management) Section 2 Gas Supply 11 SP 7(Part 10): 2005 National Building Code of India 2005: Part 10 Landscaping, signs and outdoor display structures Section 1 Landscape planning and Design Section 2 Signs and outdoor display structures DRAFT STANDARDS COMPLETED WIDE CIRCULATION 1 DOC.CED 46(7830) Draft Amendment No. 1 to NBC 2005 (to incorporate 'Part 11 Approach to Sustainability') * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 95 No. of Amd. CED 47 PORTS, HARBOURS AND OFFSHORE INSTALLATIONS SCOPE - FORMULATION OF STANDARD, CODES AND RECOMMENDATIONS RELATING SPECIFICALLY TO i) PORTS AND HARBOURS AND OTHER ANCILLARY STRUCTURES ii) OFFSHORE STRUCTURES LIAISON ISO/TC 67/SC 7 OFFSHORE STRUCTURES Sl No. IS Number/ DOC Number Title Reaffirm Date No. of Amd. STANDARDS PUBLISHED 1 IS 4651(Part 1):1974 Code of practice for planning and design of ports and harbours: Part 1 Site investigation (first revision) Aug 2012 2 IS 4651(Part 2):1989 Ports and harbours - Planning and design - Code of practice: Part 2 Earth pressure (first revision) Aug 2010 3 IS 4651(Part 3):1974 Code of practice for planning and design of ports and harbours: Part 3 Loading_(first revision) Aug 2012 4 * IS 4651(Part 4):1989 Code of practice for planning and design of ports and harbours: Part 4 General design consideration (second revision) Aug 2010 5 IS 4651(Part 5):1980 Code of practice for planning and design of ports and harbours: Part 5 Layout and functional requirements Aug 2012 6 IS 7314:1974 Glossary of terms relating to port and harbour engineering Aug 2012 7 IS 9527(Part 1):1981 Code of practice for design and construction of port and harbour structures: Part 1 Concrete monoliths Aug 2012 8 IS 9527(Part 3):1983 Code of practice for design and construction of port and harbour structures: Part 3 Sheet pile walls Aug 2012 9 IS 9527(Part 4):1980 Code of practice for design and construction of port and harbour structures: Part 4 Cellular sheet pile structures Aug 2012 10 IS 9527(Part 6):1989 Code of practice for design and construction port and harbour structures Part 6 Block work Aug 2010 11 IS 10020(Part 4):1981 Recommendations for design and construction of port and harbour components: Part 4 Slipways Aug 2012 FINILIZED DRAFTS UNDER PRINT 1 DOC.CED 47(7818) Code of practice for planning and design of ports and harbours: Part 4 General design consideration (third revision of IS 4651(Part 4)) * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 96 2 1 CED 48 ROCK MECHANICS SCOPE - FORMULATION OF INDIAN STANDARD IN THE FIELD OF ROCK MECHANICS COVERING FIELD AND LABORATORY TESTS, ROCK SAMPLING, CLASSIFICATION OF ROCK AND ROCK MASSES FOR ENGINEERING PURPOSES, LOAD BEARING CAPACITIES OF ROCK MASSES, IMPROVEMENT OF ROCK MASS AND ROCK SLOPES LIAISON: ISO/TC 182 (O) GEOTECHNICS Sl No. IS Number/ DOC Number Title Reaffirm Date No. of Amd. STANDARDS PUBLISHED 1 IS 7317:1993 Code of practice for uniaxial jacking test for deformation modulus of rock (first revision) Jul 2010 2 IS 7746:1991 Code of practice for in-situ shear test on rock (first revision) Jul 2010 3 IS 8764:1998 Method of determination of point load strength index of rocks (First Revision) 4 IS 9143:1979 Method for the determination of unconfined compressive strength of rock materials Apr 2011 5 IS 9179:1979 Method for the preparation of rock specimen for laboratory Apr 2011 6 IS 9221:1979 Method for the determination of modulus of elasticity and Poisson's ratio of rock materials in uniaxial compression Apr 2011 7 IS 10050:1981 Method for determination of slake durability index of rocks Apr 2011 8 IS 10082:1981 Method of test for the determination of tensile strength by indirect tests on rock specimens Apr 2011 9 IS 10782:1983 Method for laboratory determination of dynamic modulus of rock core specimens Apr 2011 10 IS 11309:1985 Method of conducting pull-out test on anchor bars and rock bolts Apr 2011 11 IS 11315(Part 1):1987 Method for the quantitative description of discontinuities in rock mass: Part 1 Orientation Apr 2011 12 IS 11315(Part 2):1987 Method for the quantitative description of discontinuities in rock mass: Part 2 Spacing Apr 2011 13 IS 11315(Part 3):1987 Method for the quantitative description of discontinuities in rock mass: Part 3 Persistence Jul 2010 14 IS 11315(Part 4):1987 Method for the quantitative description of discontinuities in rock mass: Part 4 Roughness Jul 2010 15 IS 11315(Part 5):1987 Method for the quantitative description of discontinuities in rock mass: Part 5 Wall strength Apr 2011 16 IS 11315(Part 6):1987 Method for the quantitative description of discontinuities in rock mass: Part 6 Aperture Apr 2011 17 IS 11315(Part 7):1987 Method for the quantitative description of discontinuities in rock mass: Part 7 Filling Jul 2010 18 IS 11315(Part 8):1987 Method for the quantitative description of discontinuities in rock mass: Part 8 Seepage Jul 2010 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS March 2014 ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 97 1 2 Sl No. IS Number/ DOC Number Title Reaffirm Date 19 IS 11315(Part 9):1987 Method for the quantitative description of discontinuities in rock mass: part 9 Number of sets Apr 2011 20 IS 11315(Part 10):1987 Method for the quantitative description of discontinuities in rock mass : Part 10 Block size Apr 2011 21 IS 11315(Part 11):1985 Method for the quantitative description of discontinuities in rock mass: Part 11 Core recovery and rock quality Apr 2011 22 IS 11315(Part 12):1992 Method for the quantitative description of discontinuities in rock mass:: Part12 Drill core study Apr 2011 23 IS 11358:1987 Glossary of terms and symbols relating to rock mechanics Jul 2010 24 IS 12608:1989 Methods of test for hardness of rock Jul 2010 25 IS 12634:1989 Method of determination for direct shear strength of rock joints Jul 2010 26 IS 12955(Part 1):1990 Code of practice for in-situ determination of rock mass deformability using a flexible dilatometer Part 1 Volume Apr 2011 27 IS 12955(Part 2):1990 Code of practice for in-situ determination of rock mass deformability using a flexible dilatometer Part 2 Radial displacement Apr 2011 28 IS 13030:1991 Method of test for laboratory determination of water content, porosity, density and related properties of rock material Apr 2011 29 IS 13047:1991 Method for determination of strength of rock materials in triaxial compression Apr 2011 30 IS 13063:1991 Code of practice for structural safety of buildings on shallow foundations on rocks Apr 2011 31 IS 13365(Part 1):1998 Quantitative classification system of rock mass - Guidelines : Part 1 RMR for predicting of engineering properties Apr 2011 32 IS 13365(Part 2):1992 Quantitative classification systems of rock mass-Guidelines Part 2 Rock mass quality for prediction of support pressure in underground openings Apr 2011 33 IS 13365(Part 3):1997 Quantitative classification system of rock mass्-्Guidelines Part 3 Determination of slope mass rating (SMR) Jun 2012 34््््््IS 13365(Part 4):2014््््् Quantitative Classification Systems of Rock Mass ्- Guidelines ््््््््््््््््््््््््््््््््््Part 4 Geological Strength Index (GSI) 35 IS 13372(Part 1):1992 Code of practice for seismic testing of rock mass: Part 1 within a borehole Apr 2011 36 IS 13372(Part 2):1992 Code of practice for seismic testing of rock mass: Part 2 Between the borehole Apr 2011 37 IS 13414:1992 Guidelines for monitoring of rock movement and multi-point borehole extensometers Apr 2011 38 IS 13946(Part 1):1994 Code of practice for in-situ determination of rock stress Part 1 Using hydraulic fracturing technique Jul 2010 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 98 No. of Amd. 1 1 1 Sl No. IS Number/ DOC Number Title 39 IS 13946(Part 2):1994 Code of practice for determination of rock stress Part 2 Using USBM type drill hole deformation gauge 40 IS 13946(Part 3):1994 Code of practice for determination of rock stress Part 3 Using a CSIR or CSIRO type cell with 9 or 12 strain gauges Jul 2010 41 IS 13946(Part 4):1994 Determination of rock stress-Code of practice Part 4 Using flat jack technique Jul 2010 42 IS 14243(Part 1):1995 Guidelines for selection and development of site for building Jul 2010 in hill areas Part 1 Microzonation of urban centres 43 IS 14243(Part 2):1995 44 IS 14395:1996 Guidelines for selection and development of site for building in hill areas Part 2 Selection and development Guidelines for monitoring of rock movements using probe inclinometer 45 IS 14396(Part 1):1996 Methods for laboratory testing of argillaceous swelling rocks Part 1 Methods of sampling storage and preparation of test Apr 2011 46 IS 14396(Part 2):1996 Methods for laboratory testing of argillaceous swelling rocks Part 2 Determination of maximum axial swelling stress Apr 2011 47 IS 14396(Part 3):1996 Methods for laboratory testing of argillaceous rocks Part 3 Determination of axial and radial free swelling strain Apr 2011 48 IS 14396(Part 4):1996 Methods for laboratory testing of argillaceous swelling rock Part 4 Determining axial swelling stress as a function of axial swelling strain Apr 2011 49 IS 14436:1997 Method of test for laboratory determination of resistivity of rock specimen Jun 2012 1 50 IS 14448:1997 Code of practice for reinforcement of rock slopes with plane wedge failure Jun 2012 1 51 IS 14881:2001 Method for blast vibration monitoring - Guidelines Apr 2011 52 IS 15026:2002 Guidelines for tunnelling methods in rock masses Jun 2012 53 IS 15180:2002 Guidelines for use in the prediction of subsidence and associated parameters in coal mines having nearly horizontal single seam workings Jun 2012 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS Reaffirm No. of Date Amd. Jul 2010 Jul 2010 Jun 2012 ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 99 1 CED 50 PLASTIC PIPING SYSTEM SCOPE - STANDARDIZATION OF PIPES, FITTINGS AND AUXILIARIES INTENDED FOR THE TRANSPORT OF FLUIDS AND FOR CABLE DUCTING MADE FROM ALL TYPES OF PLASTIC MATERIALS INCLUDING REINFORCED PLASTICS METAL FITTINGS AND RUBBER GASKETS USED WITH PLASTIC PIPES. THE SCOPE FURTHER COVERS STANDARDIZATION FOR DIMENSIONS AND THEIR TOLERANCES, REQUIREMENTS AND TEST METHODS FOR CHEMICAL, MECHANICAL AND PHYSICAL PROPERTIES AS RELEVANT TO PARTICULAR APPLICATION AND CODES OF PRACTICES FOR LAYING AND INSTALLATION LIAISON: ISO 138 (O) PLASTIC PIPES, FITTINGS AND VALVES FOR THE TRANSPORT OF FLUIDS SC 1, SC 2, SC 3, SC 4, SC 5, SC 6 AND SC 7 (O) Sl No. IS Number/ DOC Number Title Reaffirm Date No. of Amd. STANDARDS PUBLISHED 1 * IS 4984:1995 Specification for high density polyethylene pipes for potable water supplies (fourth revision) Sep 2012 6 2 IS 4985:2000 Specification for unplasticised PVC pipes for potable water supplies (third revision) Jul 2010 4 3 IS 7634(Part 1):1975 Code of practice for plastic pipes work for potable water supplies: Part 1 Choice of materials and general Sep 2012 2 4 IS 7634(Part 2):2012 Code of practice for plastics pipe work for potable water supplies: Part 2 Laying and jointing of polyethylene (PE) pipes (First Revision) 5 IS 7634(Part 3):2003 Plastic pipes selection, handling, storage and installation for potable water supplies - Code of practice Part 3 Laying and jointing of UPVC pipes (first revision) June 2013 6 IS 7834(Part 1):1987 Specification for injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 1 General requirements (first revision) June 2013 7 IS 7834(Part 2):1987 Specification for injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 2 Specific requirements for 45 degrees elbows (first revision) June 2013 IS 7834(Part 3):1987 Specification for injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 3 Specific requirements for 90 degree elbows (first revision) June 2013 9 IS 7834(Part 4):1987 Specification for injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 4 Specific requirements for 90 degree tees (first revision) June 2013 10 IS 7834(Part 5):1987 Specification for injection moulded PVC socket fittings for solvent cement joints for water supplies: Part 5 Specific requirements for 45 degree tees (first revision) June 2013 11 IS 7834(Part 6):1987 Specification for injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 6 Specific requirements for sockets (first revision) June 2013 12 IS 7834(Part 7):1987 Specification for injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 7 Specific requirements for unions (first revision) June 2013 8 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 100 Sl No. IS Number/ DOC Number Title Reaffirm Date 13 IS 7834(Part 8):1987 Specification for injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 8 Specific requirements for caps (first revision) June 2013 14 IS 8008(Part 1):2003 Injection moulded/machined high density polyethylene (HDPE) fittings for potable water supplies - Specification: Part 1 General requirements for fitting (first revision) June 2013 15 IS 8008(Part 2):2003 Injection moulded/machined high density polyethylene (HDPE) fittings for potable water supplies - Specification Part 2 Specific requirements for 90 degree bend (first revision) June 2013 16 IS 8008(Part 3):2003 Injection moulded/machined high density polyethylene (HDPE) fittings for potable water supplies - Specification: Part 3 Specific requirements for 90 degree tees (first revision) June 2013 17 IS 8008(Part 4):2003 Injection moulded/machined high density polyethylene (HDPE) fittings for potable water supplies - Specification : Part 4 Specific requirements for reducers (first revision) June 2013 18 IS 8008(Part 5):2003 Injection moulded/machined high density polyethylene (HDPE) fittings for potable water supplies - Specification Part 5 Specific requirements for ferrule reducers (first revision) June 2013 19 IS 8008(Part 6):2003 Injection moulded /machined high density polyethylene (HDPE) fittings for potable water supplies - Specification: Part 6 Specific requirements for pipe ends (first revision) June 2013 20 IS 8008(Part 7):2003 Injection moulded /machined high density polyethylene (HDPE) fittings for potable water supplies - Specification : Part 7 Specific requirements for sandwich flanges (first revision) June 2013 21 IS 8008(Part 8):2003 Injection moulded/machined high density polyethylene (HDPE) fittings for potable water supplies: Part 8 Specific requirements for reducing tees (first revision) June 2013 22 IS 8008(Part 9):2003 Injection moulded/machined high density polyethylene (HDPE) fittings for potable water supplies - Specification Part 9 Specific requirements for ends caps (first revision) June 2013 23 IS 8360(Part 1):1977 Specification for fabricated high density polyethylene (HDPE) fittings for potable water supplies: Part 1 General requirements Sep 2012 24 IS 8360(Part 2):1977 Specification for fabricated high density polyethylene (HDPE) fittings for potable water supplies, Part 2 Specific requirements for 90 degree tees Sep 2012 25 IS 8360(Part 3):1977 Specification for fabricated high density polyethylene (HDPE) fittings for potable water supplies, Part 3 Specific requirements for 90 degree bends Sep 2012 26 IS 9271:2004 Unplasticized polyvinyl chloride UPVC single wall corrugated pipes for drainage - Specification (First Revision) Jun 2009 27 IS 10124(Part 1):2009 Fabricated PVC-U fittings for potable water supplies Specification: Part I General requirements (second revision) * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 101 No. of Amd. 1 2 Sl No. IS Number/ DOC Number Title Reaffirm Date 28 IS 10124(Part 2):2009 Fabricated PVC-U fittings for potable water supplies Specification: Part 2 Specific requirements for sockets (second revision) 29 IS 10124(Part 3):2009 Fabricated PVC-U fittings for potable water supplies Specification: Part 3 Specific requirements for straight reducers (second revision) 30 IS 10124(Part 4):2009 Fabricated PVC-U fittings for potable water supplies Specification: Part 4 Specific requirements for caps (second revision) 31 IS 10124(Part 5):2009 Fabricated PVC-U fittings for potable water supplies Specification: Part 5 Specific requirements for equal tees (second revision) 32 IS 10124(Part 6):2009 Fabricated PVC-U fittings for potable water supplies Specification: Part 6 Specific requirements for flanged tail piece with metallic flanges (second revision) 33 IS 10124(Part 7):2009 Fabricated PVC-U fittings for potable water supplies Specification: Part 7 Specific requirements for threaded adaptors (second revision) 34 IS 10124(Part 8):2009 Fabricated PVC-U fittings for potable water supplies Specification: Part 8 Specific requirements for 90 degree bends (second revision) 35 IS 10124(Part 9):2009 Fabricated PVC-U fittings for potable water supplies Specification: Part 9 Specific requirements for 60 degree bends (second revision) 36 IS 10124(Part 10):2009 Fabricated PVC-U fittings for potable water supplies Specification: Part 10 Specific requirements for 45 degree bends (second revision) 37 IS 10124(Part 11):2009 Fabricated PVC-U fittings for potable water supplies Specification: Part 11 Specific requirements for 30 degree bends (second revision) 38 IS 10124(Part 12):2009 Fabricated PVC-U fittings for potable water supplies Specification: Part 12 Specific requirements for 22 1/2 degree bends (second revision) 39 IS 10124(Part 13):2009 Fabricated PVC-U fittings for potable water supplies Specification: Part 13 Specific requirements for 11 1/4 degree bends (second revision) 40 IS 12231:1987 Specification for unplasticized PVC pipes for use in suction and delivery lines of agricultural pump sets 41 IS 12235(Part 1):2004 Thermoplastic pipes and fittings - Methods of test: Part 1 Measurement of dimensions Jun 2009 42 IS 12235(Part 2):2004 | ISO 2507-1 Thermoplastic pipes and fittings - Methods of test: Part 2 Determination of vicat softening temperature Jun 2009 43 IS 12235(Part 3):2004 | ISO 7686 Thermoplastic pipes and fittings - Methods of test: Part 3 Test for opacity Jun 2009 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS June 2013 ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 102 No. of Amd. 1 Sl No. IS Number/ DOC Number Title Reaffirm Date 44 IS 12235(Part 4):2004 Thermoplastic pipes and fittings - Methods of test: Part 4 Determining the detrimental effect on the composition of water 45 IS 12235(Part 5/Sec 1):2004 Thermoplastic pipes and fittings - Methods of test: Part 5 Longitudinal reversion Section 1 Determination methods Jun 2009 46 IS 12235(Part 5/Sec 2):2004 Thermoplastic pipes and fittings - Methods of test: Part 5 + Jun 2009 47 IS 12235(Part 6):2004 Thermoplastic pipes and fittings - Methods of test: Stress relief test Jun 2009 48 IS 12235(Part 7):2004 Thermoplastic pipes and fittings - Methods of test: Part 7 Resistance of sulphuric acid Jun 2009 49 IS 12235(Part 8/Sec 1):2004 Thermoplastic pipes and fittings - Methods of test: Part 8 Resistance to internal hydrostatic pressure Section 1 Resistance to internal hydrostatic pressure at constant internal Jun 2009 50 IS 12235(Part 8/Sec 2):2004 | ISO 13845 Thermoplastic pipes and fittings - Methods of test: Part 8 Resistance to internal hydrostatic pressure Section 2 Leak-tightness of elastomeric sealing ring type socket joints under positive internal pressure and with angular deflection Jun 2009 51 IS 12235(Part 8/Sec 3):2004 | ISO 13844 Thermoplastic pipes and fittings - Methods of test: Part 8 Resistance to internal hydrostatic pressure Section 3 Leak-tightness of elastomeric sealing ring type socket joints under negative internal pressure and with angular deflection Jun 2009 52 IS 12235(Part 8/Sec 4):2004 Thermoplastic pipes and fittings - Methods of test: Part 8 Resistance to internal hydrostatic pressure Section 4 Leak-tightness of elastomeric sealing ring type socket joints under positive internal pressure without angular deflection Jun 2009 53 IS 12235(Part 9):2004 Thermoplastic pipes and fittings - Methods of test: Part 9 Resistance to external blows (Impact resistance) at 0° C (Round-the-clock method) Jun 2009 54 IS 12235(Part 10):2004 Thermoplastic pipes and fittings - Methods of test: Part 10 Determination of organotin as tin aqueous solution Jun 2009 55 IS 12235(Part 11):2004 Thermoplastic pipes and fittings - Methods of test: Part 11 Resistance to dichloromethane at specified temperature Jun 2009 56 IS 12235(Part 12):2004 Thermoplastic pipes and fittings - Methods of test Part 12 Determination of titanium dioxide content Jun 2009 57 IS 12235(Part 13):2004 Thermoplastic pipes and fittings - Methods of test Part 13 Determination of tensile strength and elongation Jun 2009 58 IS 12235(Part 14):2004 Thermoplastic pipes and fittings - Methods of test Part 14 Determination of density/relative density (specific Jun 2009 59 IS 12235(Part 15):2004 Thermoplastic pipes and fittings - Methods of test Part 15 Determination of vinyl chloride monomer content Jun 2009 60 IS 12235(Part 16):2004 Thermoplastic pipes and fittings - Methods of test Part 16 High temperature test Jun 2009 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS Part 6 Jun 2009 ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 103 No. of Amd. 1 Sl No. IS Number/ DOC Number Title Reaffirm Date 61 IS 12235(Part 17):2004 | ISO 3451-5 Thermoplastic pipes and fittings - Methods of test Part 17 Determination of ash content and sulphated ash content Jun 2009 62 IS 12235(Part 18):2004 | ISO 9969 Thermoplastic pipes and fittings - Methods of test Part 18 Determination of ring stiffness Jun 2009 63 IS 12235(Part 19):2004 Thermoplastic pipes and fittings - Methods of test Part 19 Flattening test Jun 2009 64 IS 12709:1994 Specification for glass-fibre reinforced plastic (GRP) pipes joints and fittings for use for potable water supply (first revision) Jun 2009 65 IS 12818:2010 Unplasticized polyvinyl chloride (PVC-U) screen and casing pipes for bore/tubewells - Specification (Second Revision) 66 IS 13592:2013 67 IS 13593:1992 Specification for UPVC pipe fittings to be used with the UPVC pipes in the suction and delivery lines of agricultural pumps Sep 2012 68 IS 13916:1994 Jun 2009 69 IS 14333:1996 Code of practice for installation of glass fibre reinforced plastic (GRP) piping system High density polyethylene pipes for sewerage - Specification 70 IS 14402:1996 71 No. of Amd. 4 1 Unplasticized polyvinyl chloride (PVC-U) pipes for soil and waste discharge system for inside and््outside buildings including ventilation and rain water system - Specification (First Revision of IS 13592) Feb 2012 4 Specification for GRP pipes, joints and fittings for use for sewerage, industrial waste and water (other than potable) Feb 2012 1 IS 14735:1999 Unplasticized polyvinyl chloride (UPVC) injection moulded fittings for soil and waste discharge system for inside and outside buildings including ventilation and rain water system Specification. Jun 2009 2 72 IS 14787:2000 Unplasticized PVC pipes (ducts) and fittings for underground telecommunications cable installation - Specification Jul 2010 1 73 IS 14885:2001 Specification for polyethylene pipe for supply of gaseous fuel Feb 2012 2 74 IS 15265:2003 Flexible PVC pipes polymer reinforced thermoplastic hoses for suction and delivery lines of agricultural pumps - Specification June 2013 1 75 IS 15328:2003 Unplasticized non-pressure polyvinyl chloride (PVC-U) pipes for use in underground drainage and sewerage system - Specification June 2013 5 76 IS 15450:2004 Specification for polyethylene/aluminium/polyethylene composite pressure pipes for hot and cold water supplies Jun 2009 2 77 IS 15778:2007 Chlorinated polyvinyl chloride (CPVC) pipes for potable hot and cold water distribution supplies - Specification Sep 2012 2 78 IS 15801:2008 Polypropylene-random copolymer pipes for hot and cold water supplies - Specification Sep 2012 1 79 IS 15927(Part 1):2012 Specification for polyethylene fittings for use with polyethylene pipes for the supply of gaseous fuels: Part 1 Fittings for sockets using heated tools 80 IS 15927(Part 2):2012 Specification for polyethylene fittings for use with polyethylene pipes for the supply of gaseous fuels: Part 2 Spigot fittings for butt fusion jointing or socket fusion using heated tools, spigot fittings for use with electro-fusion fittings * INDICATES STANDARDS UNDER REVISION ** INDICATES STANDARDS TO BE REVISED 104 / INDICATES DUAL NUMBER STANDARDS | INDICATES EQUIVALENT STANDARDS Sl No. IS Number/ DOC Number Title Reaffirm Date 81 IS 15927(Part 3):2011 Specification for polyethylene fittings for use with polyethylene pipes for the supply of gaseous fuels: Part 3 Electro-fusion fittings 82 IS 16098(Part 1):2013 Structured - Wall Plastics Piping Systems for Non- Pressure Drainage and Sewerage - Specification Part 1: Pipes and Fittings with Smooth External Surface, Type A 83 IS 16098(Part 2):2013 Structured - Wall Plastics Piping Systems for Non- Pressure Drainage and Sewerage - Specification Part 2: Pipes and Fittings with Non-Smooth External Surface, Type B 84््््््IS 16130:2014 Thermoplastics Materials for Pipes and Fittings for Pressure ्््् /ISO 12162 Applications – Classification and Designation – Overall ््््््््््््््् Service (Design) Coefficient (Adoption of ISO 12162) 85 SP 57: 1993 Handbook for pipes and fittings for drinking water supply FINALISED DRAFTS UNDER PRINT 1. 2. DOC.CED 50(7842) Doc: CED 50(7900) Plastics Pipes and Fittings Combined Chemical Resistance Classification Table (Adoption of ISO/TR 10358:1993) Draft Amendment No 1 to IS 16098 (Part 2):2013 Structured – Wall Plastics Piping Systems for Non- Pressure Drainage and Sewerage - Specification Part 2: Pipes and Fittings with Non-Smooth External Surface, Type B 3 DOC.CED 50(7841)R Draft Indian Standard Plastics Piping and Ducting Systems Determination of the Long-Term Hydrostatic Strength of Thermoplastics Materials in Pipe Form by Extrapolation (Adoption of ISO 9080:2003) 4 DOC: CED 50(7915) Draft Indian Standard for Polyethylene pipes for water supply – Specification (fifth revision of IS 4984) * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 105 No. of Amd. CED 51 PLANNING, HOUSING AND PREFABRICATED CONSTRUCTION SCOPE - FORMULATION OF STANDARDS: a) TO COVER VARIOUS ASPECTS OF PLANNING IN RURAL AND URBAN AREAS, BUILDING BYELAWS INCLUDING ZONING REGULATIONS, PRIMARY ELEMENTS IN THE DESIGN OF BUILDINGS FOR VARIOUS USES, BUILDINGS MODULES AND MODULAR COORDINATION, ARCHITECTURAL AND BUILDING DRAWING PRACTICES AND PLANNING OF DRAWING OFFICES b) TO ASSIST IN THE HOUSING PROGRAMME FOR ALL GROUPS, RURAL HOUSING, ETC NOT COVERED BY OTHER COMMITTEES; COORDINATION OF WORK IN THIS AREA BY OTHER COMMITTEES, STANDARD REQUIRED FOR IMPLEMENTING HOUSING PROGRAMME WITHIN THE PROVISIONS OF NATIONAL HOUSING AND HABITAT POLICY OF THE GOVERNMENT, AND c) ON DESIGN AND CONSTRUCTION PRACTICES IN THE FIELD OF PREFABRICATED CONSTRUCTION ISO/TC 59 (O) BUILDING CONSTRUCTION ISO/TC 59/SC 4 (O) DIMENSIONAL TOLERANCES AND MEASUREMENTS Sl No. IS Number/ DOC Number Title Reaffirm Date No. of Amd. STANDARDS PUBLISHED 1 IS 962:1989 Code of practice for architectural and building drawings (second revision) Jan 2012 2 IS 1553:1989 Design of library buildings - Recommendations relating to its primary elements (second revision) Feb 2011 3 IS 2661:1978 Specification for mobile library van (first revision) Oct 2013 4 IS 2662:1978 Specification for packages for use of libraries (first revision) Oct 2013 5 IS 2663:1989 Design of buildings for archives - Recommendations relating to its primary elements (second revision) Feb 2011 6 IS 3201:1988 Criteria for design and construction of precast-trusses and purlins (first revision) Apr 2009 7 IS 4878:1986 Byelaws for construction of cinema buildings (first revision) Feb 2011 8 IS 4919:1981 Glossary of terms applicable to landscape and horticulture work (first revision) Oct 2013 9 IS 4993:1983 Glossary of terms relating to modular co-ordination (second revision) Feb 2011 10 IS 5197:1987 Recommendations for layout and planning of drawings offices (first revision) Oct 2013 11 IS 6072:1971 Specification for autoclaved reinforced cellular concrete wall slabs Jan 2012 12 IS 6073:2006 Specification for autoclaved reinforced cellular concrete floor and roof slabs (first revision) Jan 2012 13 IS 6408(Part 1):1990 Recommendations for modular co-ordination in building industry: Tolerances Part 1 Glossary of terms (first revision) Feb 2011 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS Sl No. IS Number/ DOC Number 2 ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS Title Reaffirm 106 No. of Date Amd. 14 IS 6408(Part 2):1992 Recommendations for modular co-ordination in building industry: Tolerances Part 2 Principles and applications (first revision) Feb 2011 15 IS 6820:1987 Recommendations for modular co-ordination in building industry: Applications (first revision) Oct 2013 16 IS 7564(Part 1):1974 Recommendations for co-ordination of dimensions in buildings-Arrangements of building components and assemblies: Part 1 Functional group 1 - Structures Oct 2013 17 IS 7564(Part 2):1974 Recommendations for co-ordination of dimensions in buildings-Arrangements of buildings components and assemblies :Part 2 Functional group 2 - External envelope Oct 2013 18 IS 7564(Part 3):1974 Recommendations for co-ordination of dimensions in buildings-Arrangements of building components and assemblies: Part 3 Functional group 3 Internal subdivision Oct 2013 19 IS 7564(Part 4):1975 Recommendations for co-ordination of dimensions in buildings-Arrangements of building components and assemblies: Part 4 Functional group 4 Services and drainage Oct 2013 20 IS 7564(Part 5):1975 Recommendations for co-ordination of dimensions in buildings-Arrangements of building components and assemblies: Part 5 Functional group 5 Fixtures, furniture and equipment Oct 2013 21 IS 7921:1987 Recommendations for modular co-ordination in building industry : Horizontal co-ordination (first revision) Apr 2009 22 IS 7922:1987 Recommendations for modular co-ordination in building industry: Vertical co-ordination (first revision) Oct 2013 23 IS 7973:1976 Code of practice for architectural and building working Jan 2012 24 IS 8338:1976 Recommendations relating to primary elements in the design of school library buildings Apr 2009 25 IS 8888(Part 1):1993 Guide for requirements of low income housing: Part 1 Urban area (first revision) Apr 2009 1 26 IS 10297:1982 Code of practice for design and construction of floors and roofs using precast reinforced/prestressed concrete ribbed or cored slab unit Oct 2013 1 27 IS 10316:1986 Recommendations for modular co-ordination - basic module and sub-modular increments (Equivalent to ISO 1006:1973 and ISO 6514:1982) Feb 2011 28 IS 10505:1983 Code of practice for construction of floors and roofs using precast concrete waffle units Oct 2013 29 IS 10600:1983 / ISO 2848-74 Recommendations for modular co-ordination - principles and rules Feb 2011 30 IS 11447:1985 Code of practice for construction with large panel prefabricates Oct 2013 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS Sl No. IS Number/ DOC Number 1 1 ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS Title Reaffirm 107 No. of Date 31 IS 11775:1986 Recommendations for modular co-ordination: notations and symbols for modular drawings Feb 2011 32 IS 12073:1987 Recommendations for modular co-ordination: Co-ordinating sizes for door-sets and window-sets Oct 2013 33 IS 13612(Part 1):1993 Modular co-ordination for normal brickwork - Recommendation: Part 1 Burnt clay bricks Oct 2013 34 IS 13613:1992 Recommendations for modular co-ordination in building industry: Location of structural walls and floor slabs Oct 2013 35 IS 13727:1993 Guide for requirements of cluster planning for housing Apr 2009 36 IS 13990:1994 Specification for precast reinforced concrete planks and joists for flooring and roofing Apr 2009 37 IS 13994:1994 Code of practice for design and construction of floor and roof with precast reinforced concrete planks and RC joist Apr 2009 38 IS 14142:1994 Code of practice for design and construction of floors and roofs with prefabricated brick panel Apr 2009 39 IS 14143:1994 Specification for prefabricated brick panel and partially precast concrete joist for flooring and roofing Apr 2009 40 IS 14201:1994 Specification for precast reinforced concrete channel unit for construction of floors and roofs Apr 2009 41 IS 14213:1994 Code or practice for construction of walls using precast concrete stone masonry blocks Apr 2009 42 IS 14215:1994 Code of practice for design and construction of floors and roofs with precast reinforced concrete channel units Apr 2009 43 IS 14241:1995 Specification for precast reinforced concrete L-panel for roofing Apr 2009 44 IS 14242:1995 Code of practice for design and construction of roof with LPanel units Apr 2009 45 IS 15916:2010 Building design and erection using prefabricated concrete Code of practice 46 IS 15917:2010 Building design and erection using mixed/composite construction - Code of practice * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 108 Amd. 1 CED 53 CEMENT MATRIX PRODUCTS SCOPE - STANDARDIZATION IN THE FIELD OF PRECAST CONCRETE PRODUCTS, CONCRETE PIPES, CONCRETE POLES AND FIBRE REINFORCED CEMENT PRODUCTS LIAISON: ISO/TC 77 (O) PRODUCTS IN FIBRE REINFORCED CEMENT Sl No. IS Number/ DOC Number Title Reaffirm Date No. of Amd. STANDARDS PUBLISHED 1 IS 458:2003 Precast concrete pipes (with and without reinforcement) Specification (fourth revision) Nov 2013 1 2 IS 459:1992 Specification for unreinforced corrugated and semi-corrugated asbestos cement sheets (third revision) Jan 2013 3 3 IS 783:1985 Code of practice for laying of concrete pipes (first revision) Jan 2012 3 4 IS 784:2001 Specification for prestressed concrete pipes (including specials) (second revision) Aug 2010 2 5 IS 785:1998 Specification for reinforced concrete poles for overhead power and telecommunication lines (second revision) Nov 2009 6 IS 1332:1986 Specification for precast reinforced concrete street lighting poles (first revision) Aug 2010 7 IS 1592:2003 Specification for asbestos cement pressure pipes and joints (fourth revision) Nov 2013 8 IS 1626(Part 1):1994 Specification for asbestos cement building pipes and pipe fittings, gutters and gutter fittings and roofing fittings Part 1 Pipe and pipe fittings (second revision) Aug 2010 9 IS 1626(Part 2):1994 Specification for asbestos cement building pipes and pipe fittings, gutters and gutter fittings and roofing fittings Part 2 Gutter and gutter fittings (second revision)) Aug 2010 10 IS 1626(Part 3):1994 Specification for asbestos cement building pipes and pipe fittings, gutters and gutter fittings and roofing fittings: Part 3 Roofing fitting (second revision) Aug 2010 11 IS 1678:1998 Specification for prestressed concrete poles for overhead power, traction and telecommunication lines (second revision) Nov 2013 12 IS 1916:1989 Specification for steel cylinder pipe with concrete lining and coating (first revision) Nov 2009 13 IS 2096:1992 Specification for asbestos cement flat sheets (first revision) Jan 2012 14 IS 2098:1997 Specification for asbestos cement building boards (first revision) Jan 2012 15 IS 2174:1962 Specification for reinforced concrete dust bins Jan 2013 16 IS 2185(Part 1):2005 Specification for concrete masonry units: Part 1 Hollow and solid concrete blocks (third revision) Aug 2010 17 IS 2185(Part 2):1983 Specification for concrete masonry units: Part 2 Hollow and solid light weight concrete blocks (first revision) (superseding IS 3590) Aug 2010 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 109 1 1 Sl No. IS Number/ DOC Number Title Reaffirm Date 18 IS 2185(Part 3):1984 Specification for concrete masonry units Part 3 Autoclaved cellular Aerated concrete blocks (first revision) (Superseding IS 5482) 19 IS 2185(Part 4):2008 Concrete masonry units - Specification: Cellular concrete blocks using preformed foam 20 IS 2193:1986 Specification for precast prestressed concrete street lighting poles (first revision) Jan 2012 21 IS 2572:2005 Code of practice for construction of hollow and solid concrete block masonry (first revision) Aug 2010 22 IS 2905:1989 Methods of test for concrete poles for overhead power and telecommunication lines (first revision) Jan 2012 23 IS 3007(Part 1):1999 Code of practice for laying of asbestos cement sheets: Part 1 Corrugated sheets(first revision) Nov 2009 24 IS 3007(Part 2):1999 Code of practice for laying of asbestos cement sheets: Part 2 Semi-corrugated sheets (first revision) Nov 2009 25 IS 3597:1998 Methods of test for concrete pipes (second revision) Nov 2013 26 IS 3632:1969 Method of test for determination of wet volume of asbestos Jan 2012 27 IS 4350:1967 Specification for concrete porous pipes for under-drainage Jan 2012 28 IS 4844:1968 Method of sampling and preparation of asbestos fibre for laboratory test purposes Jan 2012 29 IS 4996:1984 Specification for reinforced concrete fence posts (first revision) Aug 2010 30 IS 5328:1969 Method of test for determination of chemical composition of asbestos fibre Jan 2012 31 IS 5748:1969 Methods of test for tensile strength of asbestos fibre Aug 2010 32 IS 5751:1984 Specification for precast concrete coping blocks (first revision) Jan 2012 33 IS 5758:1984 Specification for precast concrete kerbs channels, edgings, quadrants and gutter aprons (first revision) Aug 2010 34 IS 5820:1970 Specification for precast concrete cable cover Jan 2012 35 IS 5913:2003 Methods of test for asbestos cement products (second revision) Nov 2013 36 IS 6041:1985 Code of practice for construction of autoclaved cellular concrete block masonry (first revision) Aug 2010 37 IS 6042:1969 Code of practice for construction of lightweight concrete block masonry Aug 2010 38 IS 6441(Part 1):1972 Methods of test for autoclaved cellular concrete products: Part 1 Determination of unit weight or bulk density and moisture Jan 2012 39 IS 6441(Part 2):1972 Methods of test for autoclaved cellular concrete products: Part 2 Determination of drying shrinkage Jan 2012 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS Aug 2010 ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 110 No. of Amd. 1 2 Sl No. IS Number/ DOC Number Title Reaffirm Date 40 IS 6441(Part 4):1972 Methods of test for autoclaved cellular concrete products: Part 4 Corrosion protection of steel reinforcement in autoclaved cellular concrete Jan 2012 41 IS 6441(Part 5):1972 Methods of test for autoclaved cellular concrete products: Part 5 Determination of compressive strength Jan 2012 42 IS 6441(Part 6):1973 Methods of test for autoclaved cellular concrete products: Part 6 Strength, deformation and cracking of flexural members subjects to bending, short duration loading test Jan 2012 43 IS 6441(Part 7):1973 Methods of test for autoclaved cellular concrete products: Part 7 Strength, deformation and cracking of flexural members subject to bending sustained loading test Jan 2012 44 IS 6441(Part 8):1973 Methods of test for autoclaved cellular concrete products: Part 8 Loading tests for flexural members in diagonal tension Jan 2012 45 IS 6441(Part 9):1973 Methods of test for autoclaved cellular concrete products: Part 9 Jointing of autoclaved cellular concrete elements Jan 2012 46 IS 6523:1983 Specification for precast reinforced concrete door and window frames (first revision) Jan 2013 2 47 IS 6530:1972 Code of practice for laying of asbestos cement pressure pipes Jan 2012 1 48 IS 6908:1991 Specification for asbestos cement pipes and fittings for sewerage and drainage(first revision) Jan 2012 49 IS 7319:1974 Specification for perforated concrete pipes Aug 2010 50 IS 7321:1974 Code of practice for selection, handling and erection of concrete poles for overhead power and telecommunication Aug 2010 51 IS 7322:1985 Specification for specials for steel cylinder reinforced concrete pipes (first revision) Aug 2010 52 IS 7639:1975 Methods of sampling of asbestos cement products Nov 2009 53 IS 8870:1978 Specification for asbestos cement cable conduits and troughs Jan 2012 54 IS 9375:1979 Specification for precast reinforced concrete plant guards Jan 2012 55 IS 9627:1980 Specification for asbestos cement pressure pipes (light duty) Aug 2010 56 IS 9690:1980 Method of test for determination of openness or fibrization of chrysotile asbestos fibre by air permeability method using Dyckerhoff apparatus Jan 2012 57 IS 9691:1980 Method of test for length distribution (wet classification of fibre length) of chrysotile asbestos fibre using Bauer Mcnett classifier Jan 2012 58 IS 9745:1981 Method for determining strength giving properties of asbestos Jan 2012 59 IS 9872:1981 Specification for precast concrete septic tanks Jan 2012 60 IS 9893:1981 Specification for precast concrete lintels and sills Jan 2012 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 111 No. of Amd. 1 Sl No. IS Number/ DOC Number Title Reaffirm Date 61 IS 11267:1985 Method of test for length distribution (wet classification of fibre length) of chrysotile asbestos fibre using Turner and Newall classifier Aug 2010 62 IS 11275:1985 Method of test for determination of crudiness and grit content of asbestos fibre Aug 2010 63 IS 11276:1985 Method of test for determination of openness or fiberization of chrysotile asbestos fibre by air permeability method using rapid surface area apparatus Aug 2010 64 IS 11450:2006 Method for determination of airborne asbestos fibre concentration in work environment by light microscopy (membrane filter method) (first revision) 65 IS 11451:1986 Recommendations for safety and health requirements relating to occupational exposure to asbestos Aug 2010 66 IS 11707:1986 Glossary of terms relating to asbestos Aug 2010 67 IS 11767:2005 Recommendations for cleaning of premises and plants using asbestos fibres (first revision) Aug 2010 68 IS 11768:1986 Recommendations for disposal of asbestos waste material Aug 2010 1 69 IS 11769(Part 1):1987 Guidelines for safe use of products containing asbestos: Part 1 Asbestos cement products Jan 2012 1 70 IS 11769(Part 2):2005 Guidelines for safe use of products containing asbestos: Part 2 Friction materials (first revision) Feb 2011 71 IS 11769(Part 3):1986 Guidelines for safe use of products containing asbestos: Part 3 Non-cement asbestos products other than friction materials Aug 2010 72 IS 11770(Part 1):1987 Recommendations for control of emission of asbestos dust in premises manufacturing products containing asbestos: Part 1 Asbestos cement products Jan 2012 73 IS 11770(Part 2):2006 Recommendations for control of emission of asbestos dust in premises manufacturing products containing asbestos: Part 2 Friction materials (first revision) Feb 2011 74 IS 11770(Part 3):1987 Recommendations for control of emission of asbestos dust in premises manufacturing products containing asbestos: Part 3 Non-cement asbestos products other than friction materials Jan 2012 75 IS 12078:1987 Recommendations for personal protection of workers engaged in handling asbestos Jan 2012 76 IS 12079:1987 Recommendations for packaging, transport and storage of asbestos Jan 2012 77 IS 12080:1987 Recommendations for local exhaust ventilation systems in premises manufacturing products containing asbestos Jan 2012 78 IS 12081(Part 1):1987 Recommendations for pictorial warning signs and precautionary notices for asbestos and products containing asbestos: Part 1 Workplaces Jan 2012 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS Jul 2011 ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 112 No. of Amd. 1 1 1 Sl No. IS Number/ DOC Number Title Reaffirm Date 79 IS 12081(Part 2):1987 Recommendations for pictorial warning signs and precautionary notices for asbestos and products containing asbestos: Part 2 Asbestos and its products Jan 2012 80 IS 12082(Part 1):2006 Recommendations for control of asbestos emission: Part 1 Mining of asbestos ore (first revision) Feb 2011 81 IS 12082(Part 2):2006 Recommendations for control of asbestos emission: Part 2 Miling of asbestos ore (first revision) Feb 2011 82 IS 12440:1988 Specification for precast concrete stone masonry blocks Aug 2010 83 IS 12592:2002 Specification for precast concrete manhole covers and frames (first revision) Jan 2013 84 IS 13000:1990 Specification for silica asbestos cement flat sheets Aug 2010 1 85 IS 13008:1990 Specification for shallow corrugated asbestos cement sheets Aug 2010 1 86 IS 13158:1991 Specification for prestressed concrete circular spun poles for overhead power, traction and telecommunication lines Jan 2012 87 IS 13356:1992 Specification for precast ferrocement water tanks (Up to 10000 litres capacity) Jan 2012 88 IS 14862:2000 Specification for fibre cement flat sheets Aug 2010 3 89 IS 14871:2000 Specification for products in fibre reinforced cement - long corrugated or asymmetrical section sheets and fittings for roofing and cladding Aug 2010 1 90 IS 15155:2002 Specification for bar/wire wrapped steel cylinder pipes with mortar lining and coating (including specials) Jan 2013 DRAFT STANDARDS FINALIZED BUT NOT YET UNDER PRINT 1 DOC.CED 53(7839) Draft Amendment No. 4 to IS 459:1992 2 DOC.CED 53(7840) Draft Amendment No. 1 to IS 6908:1991 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 113 No. of Amd. 2 CED 54 CONCRETE REINFORCEMENT SCOPE - STANDARDIZATION IN THE FIELD OF REINFORCEMENT FOR CONCRETE INCLUDING PRE-STRESSING STEEL LIAISON: ISO/TC 17/SC 16 (O) STEEL FOR THE REINFORCEMENT AND PRESTRESSING OF CONCRETE Sl No. IS Number/ DOC Number Title Reaffirm Date No. of Amd. STANDARDS PUBLISHED 1 IS 432(Part 1):1982 Specification for mild steel and medium tensile steel bars and hard-drawn steel wire for concrete reinforcement: Part 1 Mild steel and medium tensile steel bars (third revision) Aug 2009 1 2 IS 432(Part 2):1982 Specification for mild steel and medium tensile steel bars and hard-drawn steel wire for concrete reinforcement: Part 2 Harddrawn steel wire (third revision) Aug 2009 2 3 IS 1566:1982 Specification for hard-drawn steel wire fabric for concrete reinforcement (second revision) Aug 2009 4 4 IS 1785(Part 1):1983 Specification for plain hard-drawn steel wire for prestressed concrete: Part 1 Cold-drawn stress relieved wire (second revision) Jan 2013 4 5 IS 1785(Part 2):1983 Specification for plain hard-drawn steel wire for prestressed concrete: Part 2 As drawn wire (first revision) Jan 2013 4 6 IS 1786:2008 High strength deformed steel bars and wires for concrete reinforcement - Specification (fourth revision) (superseding IS 1139:1966) Jan 2013 2 7 IS 2090:1983 Specification for high tensile steel bars used in prestressed concrete (first revision) Aug 2009 1 8 IS 6003:2010 Specification for indented wire for prestressed concrete (second revision) 9 * IS 6006:1983 Specification for uncoated stress relieved strand for prestressed concrete (first revision) Jan 2013 4 10 IS 9417:1989 Welding - cold-worked steel bars for reinforced concrete construction recommendations for welding (First Revision) Nov 2013 11 IS 10790(Part 1):1984 Methods of sampling of steel for prestressed and reinforced concrete: Part 1 Prestressing steel May 2010 12 IS 10790(Part 2):1984 Methods of sampling of steel for prestressed and reinforced concrete: Part 2 Reinforcing steel May 2010 13 IS 13620:1993 Fusion bonded epoxy coated reinforcing bars - Specification Aug 2009 1 14 * IS 14268:1995 Uncoated stress relieved low relaxation seven ply strand for prestressed concrete - Specification Jan 2013 1 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 114 FINALISED DRAFTS UNDER PRINT 1 DOC.CED 54(7662) Draft Amendment No. 2 to IS 432(Part 1):1982 Specification for mild steel and medium tensile steel bars and hard-drawn steel wire for concrete reinforcement: Part 1 Mild steel and medium tensile steel bars (third revision) 2 DOC.CED 54(7589) Draft Indian Standard for Reinforcement couplers for mechanical splices of bars for concrete reinforcement- Specification 3 DOC.CED 54(7821) Draft Indian Standard Uncoated stress relieved strand for prestressed concrete - Specification (second revision of IS 6006) 4 DOC.CED 54(7822) Draft Indian Standard Uncoated stress relieved low relaxation seven ply strand for prestressed concrete - Specification (first revision of IS 14268) * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 115 CED 55 SIEVES, SIEVING AND OTHER SIZING METHODS SCOPE - STANDARDIZATION PERTAINING TO SIZE, CLASSIFICATION FOR SOLID PARTICULATE MATERIALS INCLUDING METHODS AND METHODS OF TEST, EQUIPMENT AND MATERIALS OF EQUIPMENT LIAISON: ISO/TC 24 (O) PARTICLE CHARACTERIZATION INCLUDING SIEVING ISO/TC 24/SC 4 (O) PARTICLE CHARACTERIZATION ISO/TC 24/SC 8 (P) TEST SIEVES, SIEVING AND INDUSTRIAL SCREENS Sl No. IS Number/ DOC Number Title Reaffirm Date No. of Amd STANDARDS PUBLISHED 1 IS 460(Part 1):1985 Specification for test sieves: Part I Wire cloth test sieves (third revision) Jun 2013 2 IS 460(Part 2):1985 Specification for test sieves: Part II Perforated plate test sieves (third revision) Jun 2013 3 IS 460(Part 3):1985 Specification for test sieves: Part III Methods of examination of apertures of test sieves (third revision) Dec 2011 4 IS 1568:1970 Specification for wire cloth for general purposes (first revision) Jun 2013 5 IS 1607:2013 | ISO 2591-1:1988 1 1 Methods for test sieving (second revision) 6 IS 2405(Part 1):1980 Specification for industrial sieves: Part 1 Wire cloth sieves (first revision) Dec 2011 7 IS 2405(Part 2):1980 Specification for industrial sieves: Part 2 Perforated plates (first revision) Jun 2013 1 8 IS 3150:1982 Specification for hexagonal wire netting for general purposes (second revision) Jun 2013 1 9 IS 4124:1981 Glossary of terms relating to powders (first revision) Jul 2010 10 IS 4879:1968 Method of sub-division of gross sample of powder used for determination of particle size Jul 2010 11 IS 4961:1968 Determination of particle size of powders by air elutriatioin Jul 2010 12 IS 5257:1969 Specification for eyepiece and screen graticule for determination of particle size of powders Jul 2010 13 IS 5258:1969 Determination of particle size of powders by optical microscope method Jul 2010 14 IS 5282:1969 Liquid sedimentation methods for determination of particle size of powders Jul 2010 15 IS 5421:2013 │ISO 2395:1990 Glossary of terms relating to test sieves and test sieving (second revision) 16 IS 5742(Part 1):1970 Terms and symbols for sieve bottoms: Part 1 Woven and welded wire screens Dec 2011 17 IS 5742(Part 2):1970 Terms and symbols for sieve bottoms: Part 2 Perforated plates Jun 2013 18 IS 10483:1983 | ISO 7806:1983 Code for designating perforations of industrial plate sieves * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS Jul 2010 ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 116 CED 56 HILL AREA DEVELOPMENT ENGINEERING SCOPE - STANDARDIZATION IN THE FIELD OF DEVELOPMENTAL ACTIVITIES OF HILLY AREAS SUCH AS LANDSLIDE ANALYSIS, SITE EVALUATION FOR HUMAN SETTLEMENT, SAFE DESIGN, SELECTION OF BUILDING MATERIALS AND MODES OF CONSTRUCTION SUITABLE FOR HILLY AREAS Sl No. IS Number/ DOC Number Title Reaffirm Date STANDARDS PUBLISHED 1 IS 14458(Part 1):1998 Retaining wall for hill area - Guidelines: Part 1 Selection of type of wall Sep 2012 2 IS 14458(Part 2):1997 Retaining wall for hill area - Guidelines: Part 2 Design of retaining/breast walls Sep 2012 3 IS 14458(Part 3):1998 Retaining wall for hill area - Guidelines: Part 3 Construction of dry stone walls Sep 2012 4 IS 14496(Part 2):1998 Preparation of landslide hazard zonation maps in mountainous terrains - Guidelines: Part 2 Macro-zonation Sep 2012 5 IS 14680:1999 Landslide control - Guidelines Jan 2010 6 IS 14804:2000 Siting design and selection of materials for residential buildings in hilly areas - Guidelines Sep 2012 7 IS 14961:2001 Rainwater harvesting in hilly areas by roof water collection system – Guidelines Sep 2012 Draft Standards Formulated 1 DOC: CED 56(7889) Preliminary Draft on Preparation of Landslide Hazard Zonation Maps in Mountainous Terrains – Guidelines Part 1 – Meso scale * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 117 No. of Amd. CED 57 CYCLONE RESISTANT STRUCTURES SCOPE - FORMULATION OF INDIAN STANDARDS, RECOMMENDATIONS AND GUIDELINES ON PLANNING, DESIGN AND CONSTRUCTION OF CYCLONE RESISTANT STRUCTURES AND BUILDINGS, PROTECTION FROM HIGH SPEED WINDS, WARNING FROM CYCLONES AND TIDAL WAVES AND POST CYCLONE REHABILITATION MEASURES Sl No. IS Number/ DOC Number Title Reaffirm Date STANDARDS PUBLISHED 1 IS 15498:2004 Guidelines for improving the cyclonic resistance of low rise houses and other buildings/structures Jan 2010 2 IS 15499:2004 Guidelines for survey of housing and building typology in cyclone prone areas for assessment of vulnerability of regions and post cyclone damage estimation Jan 2010 * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 118 No. of Amd. CED 58 SUSTAINABILITY IN BUILDING CONSTRUCTION SECTIONAL COMMITTEE SCOPE - STANDARDIZATION IN THE AREA OF SUSTAINABILITY OF BUILT ENVIRONMENT Sl No. IS Number/ DOC Number Title Reaffirm Date DRAFT STANDARDS FORMULATED 1 DOC.CED 58(0) * INDICATES STANDARDS UNDER REVISION / INDICATES DUAL NUMBER STANDARDS ** INDICATES STANDARDS TO BE REVISED | INDICATES EQUIVALENT STANDARDS 119 No. of Amd. ANNEX 1 STANDARDS WITHDRAWN / SUPERSEDED Sl No. IS Number/ DOC Number Title 1 IS 515:1959 Specification for natural and manufactured aggregates for use in mass concrete (superseded by 383) 2 IS 773:1988 Specification for enamelled cast iron water-closets railway coaching stock type(fourth revision) 3 IS 775:1970 Specification for cast iron brackets and supports for wash basins and sinks (Second revision) 4 IS 776:1962 Specification for wooden water closet seats and covers (revised) 5 IS 777:1988 Specification for glazed earthenware wall tiles (second revision) 6 IS 780:1984 Sluice valves for water works purposes (5o to 300 mm size) 7 IS 849:1994 Specification for cold setting case in glue for wood (first revision) 8 IS 850:1994 Specification for natural sour (lactic) casein for glue manufacture (first revision) 9 IS 929:1959 Specification for hook ladder for fire fighting purposes (withdrawn) 10 IS 930:1977 Specification for wooden extension ladders for fire brigade use (first revision) 11 IS 931:1973 Specification for wheeled fire escape (first revision) 12 IS 932:1960 30-40 M (or 100-110 ft) Mechanically operated turn-table ladder for fire bridgade use (withdrawn) 13 IS 933:1988 Specification for portable chemical foam fire extinguisher (third revision) 14 IS 934:1988 Specification for portable fire extinguisher water type (soda acid) (fourth revision) 15 IS 935:1967 Specification for portable chemical fire extinguisher, carbon tetrachloride type (first revision) (withdrawn) 16 IS 936:1966 Specification for underground fire hydrant, double valve type (revised) (withdrawn) (see IS 909) 17 IS 938:1973 Functional requirements for 1350-1/min small fire engine (second revision) (superseded by IS 2696) 18 IS 940:2003 Specification for portable fire extinguisher, water type (gas cartridge) (fourth revision) 19 IS 945:1966 Specification for 1800-1/min motor fire engine (first revision) (superseded by IS 946) 20 IS 946:1977 Functional requirements for motor fire engine (first revision) 21 IS 953:1960 Specification for small foam crash tender (withdrawn) 120 Sl No. IS Number/ DOC Number Title Reaffirm Date 22 IS 954:1989 Functional requirements for carbon dioxide tender for fire brigade use (second revision) 23 IS 1139:1966 Specification for hot rolled mild steel, medium tensile steel and high yield strength steel deformed bars for concrete reinforcements (revised)(superseded by IS:1786) 24 IS 1200(Part 17):1985 Method of measurement of building and civil engineering works: Part 17 Road work including air field pavements (third revision) 25 IS 1233:1969 Recommendations for modular co-ordination of dimensions in the building industry (first revision) (Superseded by IS 6820) 26 IS 1256:1967 Code of practice for building byelaws 27 IS 1298:1958 Methods of test for determination of free lime in Portland cement (superseded by IS 4032) 28 IS 1329:1975 Specification for aircraft timber (Baulks and scantlings) (first revision) 29 IS 1625:1971 Code of practice for preparation of lime mortar for use in buildings (first revision) (Superseded by IS 2250) 30 IS 1629:1960 Rules for grading of cut sizes of timber (superseded by IS 1331:1971) 31 IS 1645:1960 Code of practice for fire safety of buildings (superseded by IS 1642) 32 IS 1647:1960 Code of practice for fire safety of buildings 33 IS 1648:1961 Code of practice for fire safety of building (general): Fire fighting equipment and its maintenance 34 IS 1700:1973 Specification for drinking fountains (First revision) 35 IS 1728:1960 Specification for sheet metal rain-water pipes upto 100mm nominal size, gutters, fittings and accessories 36 IS 1731:1971 Dimensions for steel flats for structural and general engineering 37 IS 1826:1983 Specification for Venetian Blinds for Windows 38 IS 1849(Part 2):1977 Guide for design and installation of vertical mixed-feed type lime kiln: Part 2 For limeshell (First revision) 39 IS 1861(Part 2):1977 Guide for manufacture of lime in vertical mixed-feed type kiln: Part 2 From limeshell (First revision) 40 IS 1910:1961 Specification for self contained breatheing apparatus for the brigade use[ Incorporated in IS 10245(Part 2) ] 41 IS 1911:1967 Schedule of unit weight of building materials (first revision) 42 IS 1924:1973 Specification for portable fire extinguisher, water type (pocket pump) (first revision) (withdrawn) 43 IS 1933:1961 Specification for portable chemical fire extinguisher chloro bromomethane type(withdrawn) 44 IS 2104:1981 Specification for water meter boxes (domestic type) (first revision) 121 No. of Amd. Sl No. IS Number/ DOC Number Title Reaffirm Date 45 IS 2171:1999 Specification for portable fire extinguishers, dry powder (cartridge type) (fourth revision) 46 IS 2178:1962 Specification for timber for use in aircraft propeller construction 47 IS 2184:1962 Tables for volume of round timber logs (withdrawn) 48 IS 2217:1982 Recommendations for providing first-aid fire fighting arrangement in public building (first revision) (withdrawn) 49 IS 2298:1977 Specification for single-barrel stirrup pump for fire fighting purposes (second revision) 50 IS 2299:1968 Specification for steel helmets for civil defence (first revision)(superseded by IS 2745:1983) 51 IS 2300:1968 Specification for non metal helmets for civil defence (first revision) (superseded by IS:2745) 52 IS 2332:1972 Nomenclature of floor and storeys (first revision) (superseded by IS 962:1967) 53 IS 2375:1963 Recommendation for modular co-ordination applied to RCC framed structures (superseded by IS 6772) 54 IS 2401:1973 Code of practice for selection, installation and maintenance of domestic water meters (First revision) 55 IS 2406:1963 Code of practice for fire safety of non-industrial buildings (withdrawn) 56 IS 2556(Part 10):1974 Specification for vitreous sanitary appliances (vitreous china): Part 10 Specific requirements of foot rests (second revision) 57 IS 2556(Part 11):1979 Specification for vitreous sanitary appliances (vitreous china): Part 11 Specific requirements for shower rose (first revision) 58 IS 2556(Part 12):1973 Specification for vitreous sanitary appliances (vitreous china): Part 12 Specific requirements of floor traps 59 IS 2556(Part 13):1973 Specification for vitreous sanitary appliances (vitreous china): Part 13 Specific requirements of traps for squatting pans 60 IS 2718:1964 Recommendations for preferred dimensions for storey heights (superseded by IS 7922) 61 IS 2720(Part 32):1970 Specification for north dakota cone test 62 IS 2906:1984 Sluice valves for water works purposes (350 to 1200 mm size) 63 IS 3076:1985 Specification for low density polyethylene pipes for potable water supplies (Second Revision) 64 IS 3102:1971 Classification of burnt clay solid bricks (first revision) (superseded by IS 1077) 65 IS 3385(Part 1):1965 Code of practice for measurement of civil engineering works: Part 1 Pile foundations (superseded by IS 1200(Part XXIII) 122 No. of Amd. Sl No. IS Number/ DOC Number Title Reaffirm Date 66 IS 3463:1966 Specification for polystyrene wall tiles 67 IS 3489:1985 Specification for enamelled steel bath tubs (First revision) 68 IS 3590:1966 Specification for load bearing light weight concrete blocks (superseded by IS 2185(Part 2) 69 IS 3805:1979 Specification for pent-top wooden cases (first revision) 70 IS 3955:1967 Code of practice for design and construction of well foundations 71 IS 4112:1967 Code of practice for fixing of polystyrene wall tiles 72 IS 4212:1978 Specification for drafting/reference tables for drawing offices (First Revision) 73 IS 4435:1967 Specification for wooden ladders and trestles 74 IS 4805:1978 Guide for construction of brick kiln (first revision) 75 IS 4838(Part 1):1969 76 IS 4838(Part 2):1979 Anthropometric dimensions for school children: Part 1 Age group 5-11 years (Superseded by IS 4838:1990) Anthropometric dimensions for school children: Part 2 Age group 1216 years (First Revision) (Superseded by IS 4838:1990) 77 IS 4962:1968 Specification for Wooden Side Sliding Doors 78 IS 5248:1988 Specification for teak logs for production of sliced veneers (first 79 IS 5417:1969 Specification for pencil tray (wooden) for use in office 80 IS 5418:1969 Specification for wood folding drawing tables 81 IS 5419:1969 Specification for wooden scribing table 82 IS 5434:1969 Specification for non-ferrous alloy bottle traps for marine use 83 IS 5482:1969 Autoclaved cellular concrete blocks [superseded by IS 2185(Part 84 IS 5490(Part 1):1977 Specification for refills for portable fire extinguishers and chemical fire engines: Part 1 For soda acid portable fire extinguishers (first revision) 85 IS 5490(Part 2):1977 Specification for refills for portable fire extinguishers and chemical fire engines: Part 2 For foam type portable fire extinguishers (first revision) 86 IS 5490(Part 3):1979 Specification for refills for portable fire extinguishers and chemical fire engines: Part 3 For soda acid chemical fire engines, 50 litre capacity (first revision) 87 IS 5490(Part 4):1979 Specification for refills for portable fire extinguishers and chemical fire engines: Part 4 For foam chemical fire engines, 50 litres capacity (first revision) 88 IS 5498:1969 Specification for lime-cement-cinder hollow concrete blocks (withdrawn) (Superseded by IS 3115) 89 IS 5506:1979 Specification for 50-l capacity chemical fire engine, soda acid type (first revision) 90 IS 5507:1979 Specification for 50-l capacity chemical fire engine, foam type (first revision) 123 No. of Amd. Sl No. IS Number/ DOC Number Title Reaffirm Date 91 IS 5869:1970 Specification for pillar taps for marine use 92 IS 5896(Part 2):1975 Code of practice for selection, operation and maintenance of special fire fighting appliances: Part 2 Escapes 93 IS 5917:1970 Specification for vitreous (vitreous china) wash basins for marine use 94 IS 6234:2003 Specification for portable fire extinguishers, water type (stored pressure) (second revision) 95 IS 6249:1971 Specification for flush valves and fittings for marine use 96 IS 6251:1971 Specification for shower fittings for marine use 97 IS 6342:1987 Specification for rosewood logs for production of sliced veneers (first revision) 98 IS 6382:1984 Code of practice for design and installation of fixed carbon dioxide for fire extinguishing system (first revision) 99 IS 6602:1972 Specification for ventilator poles 100 IS 6618:1972 Safety requirements for push chairs 101 IS 6717:1972 Specification for mobile road crane, fully sewing (superseded by IS 102 IS 6772:1972 Recommendations for dimensional co-ordination for industrialized buildings-Preferred increments 103 IS 7184:1973 Recommendations for modular co-ordination reference lines of horizontal controlling co-ordinating dimensions (superseded by IS 104 IS 7292:1974 Code of practice for in-situ determination of rock properties by flat jack 105 IS 7508:1974 Specification for wooden writing-cum-dressing table 106 IS 7550:1975 Specification for cane baskets for ration 107 IS 7612:1974 Functional requirements for flame resistant and heat resistant suits 108 IS 7630:1975 Specification for plywood drums 109 IS 8273:2000 Fibrous gypsum plaster boards (first revision) 110 IS 8321:1976 Glossary of terms applicable to plumbing work 111 IS 8358:1977 Performance test for wooden packing cases 112 IS 8403:1977 Code of practice for construction of clarification digester for treatment of sewage (withdrawn) 113 IS 8718:1978 Specification for vitreous enamelled steel kitchen sinks 114 IS 8719:1978 Specification for vitreous siphonic wash-down water closets for marine 115 IS 8727:1978 Specification for vitreous enamelled steel wash bsins 116 IS 8934:1978 Specification for cast copper alloy fancy pillar taps for water services 124 No. of Amd. Sl No. IS Number/ DOC Number Title Reaffirm Date 117 IS 9076:1979 Specification for vitreous integrated squatting pans for marine use 118 IS 10204:2001 Specification for portable fire extinguisher mechanical foam type (first revision) 119 IS 10324:1982 Specification for wooden crates for bottled drinks 120 IS 10474:1983 Specification for 150 litre capacity chemical fire engine, foam type 121 IS 10785:1983 Method for determination of compressive and tensile strength for point load tests on rock lumps 122 IS 11070:1984 Specification for bromochlorodifluoromethane (halon-1211) for fire 123 IS 12049:1987 Dimensions and tolerances relating to wood based panel materials 124 IS 13027(Part 1):1990 Methods of test for door leaves: Part 1 Measurement of dimensions and defects of squareness 125 IS 13027(Part 2):1991 Methods of test for door leaves: Part 2 Measurement of defects of general flatness 126 IS 13034:1990 Methods of test for timber panelled and glazed door shutters - type tests 127 IS 13240:1991 Specification for walnut logs for production of sliced veneers 128 IS 13435(Part 5):1992 Acrylic based polymer waterproofing material - Methods of test: Part 5 Determination of minimum film forming temperature and white point 129 IS 13519:1992 Guidelines for inspection of fixed steel offshore structures during fabrication and installation 130 IS 13711:1993 131 IS 13746:1993 Ceramic tiles - Sampling and basis of acceptance [Superseded by IS 13630(Part 15):2006] Code of practice for geotechnical investigation of offshore jacket 132 IS 13753:1993 Specification for dust pressed ceramic tiles with water absorption of E > 10 % Group B III 133 IS 13754:1993 Specification for dust pressed ceramic tiles with water absorption of 6 % < E < 10 % Group B II b) 134 IS 13755:1993 Specification for dust pressed ceramictiles with water absorption of 3% < E < 6%Group (B II a) 135 IS 13756:1993 Specification for dust pressed ceramic tiles with water absorption of E < 3% Group B I 136 IS 13802:1993 Guidelines for planning and execution of seabed engineering (Geophysical) survey for offshore platforms and pipelines 137 IS 13849:1993 Specification for portable fire extinguisher dry powder type (stored pressure) 138 IS 15397:2003 Specification for portable fire extinguisher mechanical foam type (stored pressure) 139 IS 2178:1962 Specification for timber for use in aircraft propeller construction 140.्््््IS्3311:1979 Specification्for्waste्plug्and्its्accessories्for्sinks् ््््््््््््््््््््््््््््््््््््and्wash-basins्(first्revision)्(superseded्by्IS्2693) 141 SP 6(Part 1): 1964 Handbook for structural engineers - Structural steel sections 125 No. of Amd. Sl No. IS Number/ DOC Number Title Reaffirm Date 142 SP 16(S&T): 1980 Design aids for reinforced concrete to IS 456:1978 143 SP 22(S&T): 1982 Explanatory handbook on codes for earthquake engineering (IS 1893:1975 & IS 4326:1976) 144 SP 6(Part 2): 1962 Handbook for structural engineers - Steel beams and plate girders 145 SP 6(Part 3): 1962 Handbook for structural engineers - Steel columns and struts 146 SP 24(S&T): 1983 Explanatory handbook on Indian Standard code of practice for plain and reinforced concrete (IS 456:1978) 147 SP 10(S&T): 1975 Nomograms for thickness of masonry walls 148 SP 6(Part 7): 1972 Handbook for structural engineers - Simple welded girders 149 SP 38(S&T): 1987 Handbook on typified designs for structures with steel roof trusses (with and without cranes) (Based on IS Codes) 150 SP 40(S&T): 1988 Handbook on structures with steel portal frames (without cranes) 151 SP 47(S&T): 1988 Handbook on structures with steel lattic portal frames (without cranes) 126 No. of Amd. ANNEX II LIST OF IS WITH DUAL NUMBER/EQUIVALENT STANDARDS/HARMONIZED WITH OTHER STANDARDS ORGANIZATION LIKE (II A, II B, II C etc). DUAL NUMBER STANDARDS Sl No. IS Number/ Doc No. Title ISO/IEC Number Sectional Committee of CED ISO/TC Number 1 IS 10428:1983 Glossary of terms relating to doors ISO 1804:1972 CED 11 162 2 IS 10600:1983 Recommendations for modular co- ordination - principles and rules ISO 2848-1974 CED 51 59 3 IS 10957:1999 Glossary of terms applicable for joints in building (ISO 2444-1988) ISO 2444:88 CED 13 59 4 IS 10958:1984 General check list of functions of joints in building (ISO 3447-1975) ISO 3447:75 CED 13 59 5 IS 10959:1984 Glossary of terms for sealants for building purposes (ISO 6927-1981) ISO 6927:81 CED 13 59 6 IS 11050 (Part 1): 1984 Rating of sound insulation in buildings and of building elements: Part 1 Airborne sound insulation in buildings and of interior building elements ISO 717/1-1982 CED 12 43 7 IS 11050 (Part 2): 1984 Rating of sound insulation in buildings and of building elements: Part 2 Impact sound insulation ISO 717/2-1982 CED 12 43 8 IS 11050(Part 3):1984 Rating of sound insulation in buildings and of building elements: Part 3 Airborne sound insulation of facade ISO 717/3-1982 CED 12 43 9 IS 11817:1986 Classification of joints in buildings for accommodation of dimensional deviations during construction ISO 7727:1984 CED 13 59 10 IS 11818:1986 Method of test for laboratory determination of air permeability of joints in buildings (ISO 6589-1983) ISO 6589:1983 CED 13 59 11 IS 13089:1991 Specification for furniture - storage units determination of stability ISO 7171-1988 CED 35 136 12 IS 13735:1993 Specification for evacuation signal ISO 8201-1987 CED 12 43 13 IS / ISO 6182-7 :2004 Fire Protection - Automatic Sprinkler Systems Part 7 Requirements and Test Method for Early Suppression Fast Response (ESFR) Sprinkler ISO 6182-7 :2004 CED 22 21 14 IS/ ISO 7240-5 :2003 Fire Detection and Alarm Systems Point-Type Heat Detectors ISO 7240-5 :2003 CED 22 21 audible 127 emergency Part 5 15 IS/ ISO 7240-7 :2011 Fire Detection and Alarm Systems Part 7 Point-Type Smoke Detectors using Scattered Light, Transmitted light or Ionization ISO 7240-7 :2011 CED 22 21 16 IS/ ISO 7240-11 :2011 Fire Detection and Alarm Systems Part 11 Manual Call Points ISO 7240-11 :2011 CED 22 21 17 IS/ ISO 7240-15 :2004 Fire Detection and Alarm Systems Part 15 Point-Type Fire Detectors using Scattered Light, Transmitted light or Ionization Sensor in Combination with a Heat Sensor ISO 7240-15 :2004 CED 22 21 18 IS्16130:2014 Thermoplastics Materials for Pipes and Fittings for Pressure Applicatins Classification and Designation - Overall Service (Design) Coefficient ISO12162:2009 CED्50 138 /ISO12162:2009 Total Dual Number Standards = 18 128 EQUIVALENT STANDARDS Sl No. IS Number/ Doc No. Title ISO/IEC Sectional Committee of CED ISO/TC Number 1 IS 1730:1989 Dimensions for steel plates, sheets, strips and flats for general engineering purposes ISO 1035-3: 1980 CED 7 17 2 IS 1732:1980 Dimensions for round and square steel bars for structural and general engineering purposes ISO 1035-1&2:1980 CED 7 17 3 IS 1863:1979 Specification for hot rolled steel bulb flats (first revision) ISO 657-19 CED 7 17 4 IS 1864:1979 Specification for hot-rolled steel L- sections for shipbuilding (first revision) ISO 657-18 CED 7 17 5 IS 2189:2008 Code of practice for selection, installation and maintenance of automatic fire detection and alarm system (second revision) ISO/TR 7240-14:03 CED 22 21 6 IS 2190:2010 Code of practice for selection, installation and maintenance of first-aid fire extinguishers (third revision) ISO 3941:77 CED 22 21 ISO 11602-1:00 ISO 11602-2:00 7 IS 2925:1984 Specification for industrial safety helmets (second revision) ISO 3873:77 CED 22 94 8 IS 3808:1979 Method of test for non-combustibility of building materials (first revision) ISO 1182:02 CED 36 92 9 IS 3809:1979 Fire resistance revision) ISO 834-1:99 CED 36 92 10 IS 7673:2004 Glossary of terms for fire fighting equipment (first revision) ISO 8421-1:87 CED 22 21 11 IS 8757:1999 Glossary of terms associated with fire safety ISO 13943:2000 CED 36 92 12 IS 10483:1983 Code for designating perforations of industrial plate sieves ISO 7806:1983 CED 55 24 13 IS 11134:1984 Code of practice for setting out of buildings ISO 4463 CED 13 59 14 IS 12235(Pt 2):2004 Thermoplastic pipes and fittings - Methods of test: Part 2 Determination of vicat softening temperature ISO 2507-1 CED 50 138 15 IS 12235 (Part 8/ Thermoplastic pipes and fittings - Methods of test: Part 8 Resistance to internal hydrostatic pressure Section 2 Leak- tightness of elastomeric sealing ring type socket joints under positive internal pressure and with angular deflection type socket joints under negative internal pressure and with angular deflection ISO13845:2000 CED 50 138 Sec 2): 2004 test for structures(first 129 Sl No. IS Number/ Doc No. Title ISO/IEC Sectional Committee of CED ISO/TC Number 16 IS 12235(Part 8/Sec 3):2004 Thermoplastic pipes and fittings - Methods of test: Part 8 Resistance to internal hydrostatic pressure Section 3 Leak- tightness of elastomeric sealing ring ISO 13844:2002 CED 50 138 17 IS 12235(Pt 17):2004 Thermoplastic pipes and fittings - Methods of test : Part 17 Determination of ash content and sulphated ash content ISO 3451-5:1989 CED 50 138 18 IS 12235(Pt 18):2004 Thermoplastic pipes and fittings - Methods of test : Part 18 Determination of ring stiffness ISO 9969:1994 CED 50 138 19 IS 12349:1988 Fire protection-safety signs ISO 6309:87 CED 36 21 20 IS 12835(Part 1): 1989 Code of practice for design and installation of fixed fire extinguishing system : Part 1 Low expansion foam ISO 7203-1:95 CED 22 21 21 IS 13630 (Pt 1):2006 Ceramic Tiles - Methods of Test Part 1 Determination of dimensions and surface (first revision) ISO 10545-2 CED 5 189 22 IS 13630 (Pt 2):2006 Ceramic Tiles - Methods of Test Part 2 Determination of water absorption and bulk density (first revision) ISO 10545-3 CED 5 189 23 IS 13630 (Pt 3):2006 Ceramic Tiles - Methods of Test Part 3 Determination of moisture expansion using boiling water – Unglazed tiles (first revision) ISO 10545-10 CED 5 189 24 IS 13630 (Pt 4):2006 Ceramic Tiles - Methods of Test Part 4 Determination of linear thermal expansion (first revision) ISO 10545-8 CED 5 189 25 IS 13630 (Pt 5):2006 Ceramic Tiles - Methods of Test ISO 10545-9 CED 5 189 Part 5 Determination of resistance to thermal shock (first revision) 26 IS 13630 (Pt 6):2006 Ceramic Tiles - Methods of Test Part 6 Determination of modulus of rupture and breaking strength(first revision) ISO 10545--4 CED 5 189 27 IS 13630 (Pt 7):2006 Ceramic Tiles - Methods of Test Part 7 Determination of chemical resistance – Unglazed tiles (first revision) ISO 10545-13 CED 5 189 28 IS 13630 (Pt 8):2006 Ceramic Tiles - Methods of Test Part 8 Determination of chemical resistance – Glazed tiles (first revision) ISO 10545-13 CED 5 189 29 IS 13630 (Pt 9):2006 Ceramic Tiles - Methods of Test Part 9 Determination of crazing resistance – Unglazed tiles (first revision) ISO 10545-11 CED 5 189 130 Sl No. IS Number/ Doc No. Title ISO/IEC Sectional Committee of CED 30 IS 13630 (Pt 10): 2006 Ceramic Tiles - Methods of Test Part 10 Determination of frost resistance(first revision) ISO 10545-12 CED 5 189 31 IS 13630 (Pt 11): 2006 Ceramic Tiles - Methods of Test Part 11 determination of resistance to surface abrasion – Glazed tiles(first revision) ISO 10545-7 CED 5 189 32 IS 13630 (Pt 14): 2006 Ceramic Tiles - Methods of Test Part 14 Determination of impact resistance By measurement of coefficient of restitution(first revision) ISO 10545-5 CED 5 189 34 IS 13630 (Pt 15): 2006 Ceramic Tiles - Sampling and Basis for Acceptance ISO 10545-1 CED 5 189 35 IS 14609:1999 Specification for ABC dry powder for fire fighting ISO 7202:87 CED 22 21 36 IS 14862:2000 Fibre cement flat sheets - Specification ISO 390 & ISO 8336 CED 53 77 37 IS 15105:2002 Design and installation of fixed automatic sprinkler fire extinguishing systems – Code of practice ISO 6182-1:04 CED 22 21 38 IS 15220:2002 Specification for halon 1211 and halon 1301 fire extinguishing media for fire protection ISO 7201-1:89 CED 22 21 39 IS 15221:2002 Code of practice for safe handling and transfer procedure of halon 1121 and halon 1301-fire extinguishing media ISO 7201-2:91 CED 22 21 40 IS 15222:2002 Specification for carbon-dioxide as fire extinguishing media for fire protection ISO 5923:89 CED 22 21 41 IS 15493:2004 Gaseous fire - extinguishing systems General requirements ISO 14520-1:06 CED 22 21 42 IS 15497:2004 Gaseous fire - extinguishing systems IG-01 extinguishing systems ISO 14520-12:05 CED 22 21 43 IS 15501:2004 Gaseous fire - extinguishing systems IG-541 extinguishing systems ISO 14520-15:05 CED 22 21 44 IS 15505:2004 Gaseous fire - extinguishing systems: HCFC Blend A extinguishing systems ISO 14520-6:06 CED 22 21 45 IS 15506:2004 Gaseous fire - extinguishing systems: IG 55 extinguishing systems ISO 14520-14:05 CED 22 21 131 ISO/TC Number Sl No. IS Number/ Doc No. Title ISO/IEC Sectional Committee of CED ISO/TC Number 46 IS 15517:2004 Gaseous fire extinguishing systems - HFC 227ea (Hepta Fluoro Propane)extinguishing system ISO 14520-9:06 CED 22 21 47 IS 15525:2004 Gaseous fire - extinguishing systems IG-100 extinguishing systems ISO 14520-13:05 CED 22 21 48 IS 15528:2004 Gaseous fire extinguishing systems - Carbon dioxide, total flooding and local application (Sub-floor and in-cabinet), high and low pressure (refrigerated) ISO 6183:90 CED 22 21 49 IS 15683:2006 Portable fire extinguishers performance and construction – Specification ISO 7165:99 CED22 21 50 IS 15682:2006 Fire fighting vehicles & equipment – Symbols for operator control and other display ISO 6790:86 CED22 21 51 IS 5513:1996 Specification for vicat apparatus ISO 9598:89 CED 2 74 52 IS 5514:1996 Specification for apparatus used in LeChatelier test ISO 9598:89 CED 2 74 53 IS 10316:1986 Recommendations for modular co-ordination – Basic module and sub-modular increments ISO 1006 & CED 51 59 ISO 6514 54 IS 15835:2010 Gaseous fire extinguishing systems HFC – 125 Extinguishants ISO 14520-8 CED 22 21 55 IS 4020(Pt 2);1998 Door shutters – Methods of tests Part 2 Measurement of dimensions & Squareness ISO 6443:05 CED 11 162 56 IS 4020(Pt 3);1998 Door shutters – Methods of tests Part 3 Measurement of general flatness ISO 6442:05 CED 11 162 57 IS 4020(Pt 4);1998 Door shutters – Methods of tests Part 4 Local planeness test ISO 6442:05 CED 11 162 58 IS 4020(Pt 7);1998 Door shutters – Methods of tests Part 7 Edge loading test ISO 8275:85 CED 11 162 59 IS 4020(Pt 8);1998 Door shutters – Methods of tests Part 8 Shock resistance test ISO 8270:85 CED 11 162 60 IS 12235 (Pt 3):2004 Thermoplastic pipes and fittings - Methods of tests : Part 3 Test for opacity ISO 7686:2005 CED 50 138 61 IS 5421:2013 Glossary of terms relating to test sieves and test sieving ISO 2395:1990 CED 55 24 62 IS 1607:2013 Methods for test sieving (second revision) | ISO 2591-1:1988 CED 55 24 Total EQUIVALENT STANDARDS = 62 132 ANNEX III LIST OF IS UNDER BIS CERTIFICATION MARKS 133 134 135 136 137 138 ANNEX IV LIST OF IS UNDER ECO MARK Sl No Sectional Committee IS Number Title 1 CED 4 IS 2095 (Part 1): 2011 Specification for gypsum plaster boards: Part 1 Plain gypsum plaster boards (third revision) 2 IS 2095(Part 2): 2001 Specification for gypsum plaster boards: Part 2 Coated/ laminated gypsum plaster boards 3 IS 2095(Part 3): 1996 Specification for gypsum plaster boards: Part 3 Reinforced gypsum plaster boards (second revision) 4 IS 2849:1983 Specification for non-load bearing gypsum partition blocks (solid and hollow types) IS 1003(Part 1):2003 Specification for timber panelled and glazed shutters: Part 1 Door shutters (third revision) 6 IS 1003(Part 2):1994 Specification for timber panelled and glazed shutters: Part 2 Window and ventilator shutters (third revision) 7 IS 2191(Part 1):1983 Specification for wooden flush door shutters (cellular and hollow core type) : Part 1 Plywood face panels (fourth revision) 8 IS 2191(Part 2):1983 Specification for wooden flush door shutters (cellular and hollow core type) : Part 2 Particle board and hardboard face panels (third revision) 9 IS 2202(Part 1):1999 Specification for wooden flush door shutters (solid core type): Part 1 Plywood face panels (sixth revision) 10 IS 2202(Part 2):1983 Specification for wooden flush door shutters (solid core type): Part 2 Particle board face panels and hardboard face panels (third revision) 11 IS 4021:1995 Specification for timber door, window and ventilator frames (third revision) 12 IS 6198:1992 Specification for ledged, braced and battened timber door shutters (second revision) IS 303:1989 Specification for plywood for general purposes (third revision) 14 IS 710:2010 Specification for marine plywood (second revision) 15 IS 1328:1996 Specification for veneered decorative plywood (third revision) 16 IS 1658:1977 Specification for fibre hardboards (second revision) 17 IS 1659:1990 Specification for block boards (third revision) 18 IS 3087:1985 Specification for wood particle boards (medium density) for general purposes (first revision) 19 IS 3097:1980 Specification for veneered particle boards (first revision) 20 IS 3129:1985 Specification for low density particle boards (first revision) 21 IS 3308:1981 Specification for wood wool building slabs (first revision) 22 IS 4990:1993 Specification for plywood for concrete shuttering work (second revision) 23 IS 5509:1980 Specification for fire retardant plywood (first revision) 5 13 CED 11 CED 20 139 24 IS 12406:1988 Specification for medium density fibre boards for general purposes IS 12823:1990 Specification for pre-laminated particle boards 26 IS 13958:1994 Specification for bamboo mat board for general purposes 27 IS 14587:1998 Specification for pre-laminated medium density fibre board 28 IS 14588:1999 Specification for bamboo mat veneer composites for general purposes 29 IS 14616:1999 Specification for laminated veneer lumber 30 IS14842:2000 Specification for coir veneer board for general purposes 31 IS15380:2003 Specification for moulded raised high density fibre (HDF) panel doors 32 IS 15476:2004 Specification for bamboo mat corrugated sheets 33 IS 15491:2004 Specification for medium density, coir boards for general purposes 34 IS 15877:2010 Specification for coir faced blockboards 35 IS 15878:2010 Specification for coir hardboards for general purposes IS 10658:1999 Specification for higher capacity dry powder fire extinguisher (trolley mounted) 37 IS 11833:1986 Specification for dry powder fire extinguisher for metal fires 38 IS 13385:1992 Specification for fire extinguisher 50 capacity wheel mounted water type (gas cartridge) 39 IS 1829(Part 1):1978 Specification for 50 l capacity fire extinguisher, mechanical foam type IS 4116:1988 Specification for library furniture and fittings: Part 1 Timber 25 36 40 CED 20 (Contd…) CED 22 CED 35 Specification for wooden shelving cabinets (adjustable type) (second revision) 41 42 IS 4126:1986 Specification for wooden wardrobes (adjustable type and nonadjustable type) 43 IS 4414:1990 Specification for wooden table tops (second revision) 44 IS 5823:1986 Specification for dining tables (first revision) 45 IS 5923:1986 Specification for wooden clothes lockers (first revision) 46 IS 5974:1986 Specification for divans and easy chairs (first revision) 47 IS 6188:1988 Specification for wooden bedside table (first revision) 48 IS 6632:1988 Specification for wooden folding chairs 49 IS 7070:1988 Wooden shelving racks (adjustable type and non-adjustable type) (first revision) 50 IS7259(Part1): 1988 Wooden beds: Part 1 for use with mattresses (first revision) 51 IS 11525:1986 Wooden chairs for office purposes 52 IS 11679:1986 Wooden tables for office purposes 53 IS 12680:1989 Wooden-sofa-cum-bed IS 6523:1983 Specification for pre-cast reinforced concrete door and window frames (first revision) 54 CED 53 140 ANNEX V LIST OF BILINGUAL/HINDI STANDARDS A) PUBLISHED STANDARDS IN HINDI 1 IS 10 : Part 2 1996 Specification for plywood tea-chest: Part 2 Plywood 2 IS 10 : Part 3 1974 Specification for plywood tea-chests, Part 3 Battens 3 IS 432 : Part 1 1982 4 IS 432 : Part 2 1982 5 IS 3583 1988 Specification for mild steel and medium tensile steel bars and harddrawn steel wire for concrete reinforcement: Part I Mild steel and medium tensile steel bars Specification for mild steel and medium tensile steel bars and harddrawn steel wire for concrete reinforcement: Part 2 Hard-drawn steel wire Specification for burnt clay paving bricks 6 IS 3763 1983 Specification for metal folding chairs 7 IS 8758 1993 Recommendations for fire precautionary measures in the construction of temporary structures and pandals 8 IS 11679 1986 Specification for Wooden Tables for Office Use 9 IS 13827 1993 Improving earthquake resistance of earthen buildings - Guidelines 10 IS 13828 1993 Improving earthquake resistance of low strength masonary buildings - Guidelines B) BILINGUAL STANDARDS 1 IS 269 2013 Specification for ordinary Portland cement, 33 grade 2 IS 455 1989 Specification for Portland slag cement 3 IS 1489 : Part 1 1991 Specification for Portland pozzolana cement Part 1 Flyash based 4 IS 1489 : Part 2 1991 Specification for Portland-pozzolana cement Part 2 calcined clay based 5 IS 2925 1984 Specification for Industrial Safety Helmets 6 IS 3466 1988 Specification for masonry cement 7 IS 3812 : Part 1 2003 Pulverized Fuel Ash - Specification - Part 1 : For Use as Pozzolana in Cement, Cement Mortar and Concrete 8 IS 3812 : Part 2 2003 Pulverized Fuel Ash - Specification - Part 2 : For Use as Admixture in Cement Mortar and Concrete 9 IS 3952 1988 Specification for burnt clay hollow bricks for walls and partitions 10 IS 6452 1989 Specification for high alumina cement for structural use 11 IS 6909 1990 Specification for supersulphated cement 12 IS 7556 1988 Specification for burnt clay jallies 141 13 IS 8041 1990 Specification for rapid hardening Portland cement 14 IS 8042 1989 White Portland Cement - Specification 15 IS 8043 1991 Specification for hydrophobic Portland cement 16 IS 8112 1989 Specification for 43 grade ordinary Portland cement 17 IS 12269 1987 Specification for 53 grade ordinary Portland cement 18 IS 15834 2008 Stainless steel sliding door bolts for use with padlocks Specification 142 ANNEX VI MEMBERSHIP STATUS IN ISO COMMITTEES & SUB-COMMITTEES SL. NO. 1. 2. 3. 4. 5. 6. 7. TITLE OF TC AND SC TYPE OF MEMBERSHIP TC 17 – Steel SC 3 - Steels for structure purposes P SC 16 – Steels for the reinforcement and prestressing of concrete O TC 21 – Equipment for fire protection and fire fighting O SC 2 – Manually transportable fire extinguishers SC 3 – Fire detection and alarm system SC 5 – Fixed fire extinguishing systems SC 6 – Extinguishing media fire fighting O TC 24 – Sieves, sieving and other sizing methods O SC 4 – Sizing by methods other than sieving SC 8 – Test sieves, sieving and industrial screens O P O O O TC 43 Acoustics SC 2 – Building acoustics O TC 59 – Building construction O SC 2 – Terminology and harmonization of languages SC 3 – Functions/user requirements and performance in building construction SC 8 – Jointing products SC 13 – Organization of information about construction works TC 67 – Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries O O O O O SC 7 - Off shore structures O TC 71 – Concrete, reinforced concrete and prestressed concrete P SC 1 – Test methods for concrete SC 3 – Concrete production and execution of concrete structures SC 4 – Performance requirements for structural concrete SC 5 – Simplified design standard for concrete structures SC 6 – Non traditional reinforcing materials for concrete structures SC 7 – Maintenance and repair of concrete structures SC 8 – Environment Management for concrete and concrete structures P P P O P O P 143 8. TC 74 – Cement and lime P 9. TC 77 – Products in fibre reinforced cement O 10. TC 89 – Wood based panels O SC 1 – Fibre boards SC 2 – Particle boards SC 3 – Plywood O O O TC 92 – Fire tests on building materials, components and structures O SC 1 – Reaction to fire SC 2 – Fire resistance SC 3 – Toxic hazards in fire O O O 11. 12. TC 94 – Personal safety – Protective clothing and equipment SC 1 – Head protection P TC 98 – Basis of design of structures O SC 1 – Terminology and symbols SC 2 – Reliability of structures SC 3 – Loads, forces and other actions O O O 14. TC 136 – Furniture O 15. TC 138 – Plastic pipes, fittings and valves for the transport of fluids O SC 1 – Plastic pipes and fittings for soil, waste and drainage including land drainage SC 2 – Plastic pipes and fittings for water supplies O SC 3 – Plastic pipes and fittings for industrial application SC 4 – Plastic pipes and fittings for the supply of gaseous fuels SC 5 – General properties of pipes, fittings and valves of plastic materials and their accessories, test methods and basic specifications SC 6 – Reinforced plastic pipes and fittings for all applications SC 7 – Valves and auxiliary equipment of plastics materials O 16. TC 162 – Doors and windows O 17. TC 165 – Timber structures O 18. TC 167 – Steel and aluminium structures SC 1 – Steel: material and design SC 3 – Aluminium Structures O O O 19. TC 179 – Masonry O SC 1 – Unreinforced masonry SC 2 – Reinforced masonry SC 3 – Test methods O O O TC 182 – Geotechnics O 13. 20. O O O O O 144 SC 1 – Classification and presentation SC 3 – Foundations, retaining structures and earthworks O O 21. TC 189 – Ceramic tile O 22. TC 218 Timber O P – PARTICIPATING MEMBER O – OBSERVER MEMBER 145 ANNEX VII LIST OF MANDATORY STANDARDS SL NO. IS NUMBER YEAR TITLE 1 IS 269 1989 Specification for 33 grade ordinary portland cement 2 IS 455 1989 Specification for Portland slag cement 3 IS 1489 : Part 1 1991 Specification for Portland pozzolana cement Part 1 Flyash based 4 IS 1489 : Part 2 1991 5 IS 1785 : Part 1 1983 Specification for Portland-pozzolana cement Part 2 calcined clay based Specification for Plain Hard-drawn Steel Wire for Prestressed Concrete - Part I : Cold Drawn Stress-relieved Wire 6 IS 1785 : Part 2 1983 7 IS 1786 2008 8 IS 3466 1988 Specification for masonry cement 9 IS 6003 2010 Specification for indented wire for prestressed concrete 10 IS 6006 1983 Specification for uncoated stress relieved strand for prestressed concrete 11 IS 6452 1989 Specification for high alumina cement for structural use 12 IS 6909 1990 Specification for supersulphated cement 13 IS 8041 1990 Specification for rapid hardening Portland cement 14 IS 8042 1989 White Portland Cement - Specification 15 IS 8043 1991 Specification for hydrophobic Portland cement 16 IS 8112 1989 Specification for 43 grade ordinary Portland cement 17 IS 8229 1986 Specification for Oil-well Cement 18 IS 12269 1987 Specification for 53 grade ordinary Portland cement 19 IS 12330 1988 Specification for sulphate resisting Portland cement 20 IS 12600 1989 Specification for low heat Portland cement 21 IS 13620 1993 Fusion boned epoxy coated reinforcing bars - Specification 22 IS 14268 1995 Uncoated stress relieved low relaxation seven ply strand for prestressed concrete - Specification Specification for plain hard-drawn steel wire for prestressed concrete: Part 2 As drawn wire High strength deformed steel bars and wires for concrete reinforcement - Specification 146 ANNEX VIII LIST OF IS TRANSFERED TO OTHER DEPARTMENTS (SINCE 01 APRIL 2012) 1. IS 5533:1969 Recommendation for dimensions for spaces for human activities. 2. IS 4838:1990 Anthropometric dimensions for school children age group 5-17 years (second revision) 147 ANNEX IX LIST OF SPECIAL PUBLICATIONS 1 SP 6 : Part 4 1969 ISI Handbook for Structural Engineers 4. Use of High Strength Friction Grip Bolts 2 SP 6 : Part 5 1980 3 SP 6 : Part 6 1972 4 SP 7 2005 Handbook for structural engineers - Cold-formed, light gauge steel structures Handbook for structural engineers - Application of plastic theory in design of steel structures National building code of India 2005 5 SP 7 (Group 1) 2005 National building code of India 2005: Group 1 6 SP 7 (Group 2) 2005 National building code of India 2005: Group 2 7 SP 7 (Group 3) 2005 National building code of India 2005: Group 3 8 SP 7 (Group 4) 2005 National building code of India 2005: Group 4 9 SP 7 (Group 5) 2005 National building code of India 2005: Group 5 10 SP 20(S&T) 1991 Handbook on masonry design and construction (first revision) 11 SP 21 (S&T) 2005 Summaries of Indian Standards for Building Materials 12 SP 23 1982 Handbook on Concrete Mixes 13 SP 25(S&T) 1984 Handbook on Causes and Prevention of Cracks in Building 14 SP 27 1987 Handbook on method of measurement of buildings works 15 SP 32 1986 Handbook on Functional Requirements of Industrial Buildings (Lighting and Ventilation) 16 SP 33 1987 Handbook on Timber Engineering 17 SP 34 1987 Handbook on Concrete Reinforcement and Detailing 18 SP 35 (S&T) 1987 Handbook on Water Supply and Drainage (with Special Emphasis on Plumbing) 19 SP 36 : Part 1 1987 Compendium of Indian standards on soil engineering: Part 1 Laboratory testing of soils for civil engineering purposes 20 SP 36 : Part 2 1988 Compendium of Indian standards on soil engineering: Part 2 Field testing 21 SP 41 (S&T) 1987 Handbook on Functional Requirements of Buildings (Other than Industrial Buildings) 22 SP 43 (S&T) 1987 Handbook on Structures with Reinforced Concrete Portal Frames (Without Cranes) 23 SP 57 (QAWSM) 1993 Handbook on Pipes and Fittings for Drinking Water Supply 24 SP 62 1997 Handbook on Building Construction Practices (Excluding Electrical Work) 25 SP 64 (S & T) 2001 Explanatory Handbook on Indian Standard Code of Practice for Design Loads (Other than Earthquake) for Buildings and Structures 26 SP 70 2001 Handbook on Construction Safety Practices 27 SP 1650 1973 Standard colours for building and decorative finishes (with supplement) ************** 148