Product Data Sheet Industrial MICRO SD Memory Card S-200u Series SPI and SD compliant S-200u Series MICRO SD Memory Card 1 Feature summary               highly-integrated memory controller o Fully compliant with SD Memory Card specification 2.0 and Micro SD Memory Card specification 2.0 addendum o Four integrated 4KByte Sector Buffers for fast data transfer Standard MICRO SD Memory Card form factor o 15.0mm x 11.0mm x 0.7mm 2.7…3.6V normal operating voltage 2.0…3.6V basic communication (CMD0, 15, 55 ACMD41) voltage Low-power CMOS technology Wear Leveling: equal wear leveling of static and dynamic data The wear leveling assures that dynamic data as well as static data is balanced evenly across the memory. With that the maximum write endurance of the device is guaranteed. Patented power-off reliability o No data loss of older sectors o Max. 16 sectors data loss (old data kept) if power off during writing High reliability o Best available SLC NAND Flash technology o Designed for embedded market o MTBF: > 3,000,000 hours o Number of insertions: >10,000 o Extended Temperature range: -25° up to 85°C o Industrial Temperature range: -40° up to 85°C Hot swappable CPRM keys optional High performance o SD burst up to 25MB/s o SD Low speed 0…25MHz clock rate o SD High speed 25…50MHz clock rate o Up to 21/18 MB/s sustained read/write speed o Flash burst up to 40MB/s o “Low speed cards” with disabled high speed mode available Available densities o up to 2GBytes Controlled BOM Life Time Monitoring SD/SPI with standard or vendor commands Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.10 S-200u_data_sheet_SD-NxBN_Rev110.docx Page 2 of 23 2 Order Information 2.1 Standard product list Table 1: General Product List Capacity Part Number 512MB SFSD0512NgBN1TO-t-ME-1x1-STD 1GB SFSD1024NgBN1TO-t-DF-1x1-STD 2GB SFSD2048NgBN1TO-t-QF-1x1-STD g defines the product generation t defines the temperature range (E=-25°C to +85°C, I=-40°C to +85°C) x defines the FW 2.2 Actual product list Table 2: General Product List Capacity Extended Temperature Range 512MB SFSD0512N1BN1TO-E-ME-161-STD 1GB SFSD1024N1BN1TO-E-DF-161-STD 2GB SFSD2048N1BN1TO-E-QF-161-STD Industrial Temperature Range 512MB SFSD0512N1BN1TO-I-ME-161-STD 1GB SFSD1024N1BN1TO-I-DF-161-STD 2GB SFSD2048N1BN1TO-I-QF-161-STD Part Number 2.3 Offered options for customer projects        Customer specified strings and IDs (MID, OID, PNM, PRV) Customer specified capacities Preload service Customized printing and lasering Permanent write protected (ROM) with preloaded software Diagnostic documentation for Card Status Register access or vendor command extension values … Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.10 S-200u_data_sheet_SD-NxBN_Rev110.docx Page 3 of 23 Contents 1 FEATURE SUMMARY ..................................................................................................................................................................... 2 2 ORDER INFORMATION .................................................................................................................................................................. 3 2.1 STANDARD PRODUCT LIST .......................................................................................................................................................... 3 2.2 ACTUAL PRODUCT LIST .............................................................................................................................................................. 3 2.3 OFFERED OPTIONS FOR CUSTOMER PROJECTS ................................................................................................................................. 3 3 PRODUCT SPECIFICATION ............................................................................................................................................................. 5 3.1 SYSTEM PERFORMANCE ............................................................................................................................................................ 5 3.2 ENVIRONMENTAL SPECIFICATIONS............................................................................................................................................... 5 3.2.1 Recommended Operating Conditions................................................................................................................ 5 3.2.2 Recommended Storage Conditions ................................................................................................................... 6 3.2.3 Humidity & ESD .................................................................................................................................................... 6 3.2.4 Durability .............................................................................................................................................................. 6 3.3 PHYSICAL DIMENSIONS ............................................................................................................................................................ 6 3.4 RELIABILITY .......................................................................................................................................................................... 6 4 CAPACITY SPECIFICATION ............................................................................................................................................................. 6 5 CARD PHYSICAL............................................................................................................................................................................ 7 5.1 PHYSICAL DESCRIPTION ............................................................................................................................................................ 7 6 ELECTRICAL INTERFACE ................................................................................................................................................................ 8 6.1 ELECTRICAL DESCRIPTION .......................................................................................................................................................... 8 6.2 DC CHARACTERISTICS............................................................................................................................................................... 9 6.3 SIGNAL LOADING ................................................................................................................................................................... 9 6.4 AC CHARACTERISTICS .............................................................................................................................................................10 7 HOST ACCESS SPECIFICATION.......................................................................................................................................................12 7.1 SD AND SPI BUS MODES ........................................................................................................................................................12 7.1.1 SD Bus Mode Protocol ..........................................................................................................................................12 7.1.2 SPI Bus Mode Protocol ........................................................................................................................................13 7.1.3 Mode Selection ....................................................................................................................................................13 7.2 CARD REGISTERS ...................................................................................................................................................................14 8 DECLARATION OF CONFORMITY ..................................................................................................................................................17 9 ROHS AND WEEE UPDATE FROM SWISSBIT ................................................................................................................................18 10 PART NUMBER DECODER ..........................................................................................................................................................20 10.1 MANUFACTURER ..................................................................................................................................................................20 10.2 MEMORY TYPE ....................................................................................................................................................................20 10.3 PRODUCT TYPE ....................................................................................................................................................................20 10.4 CAPACITY ...........................................................................................................................................................................20 10.5 PLATFORM .........................................................................................................................................................................20 10.6 GENERATION ......................................................................................................................................................................20 10.7 MEMORY ORGANIZATION .......................................................................................................................................................20 10.8 TECHNOLOGY ......................................................................................................................................................................20 10.9 CHANNELS .........................................................................................................................................................................20 10.10 FLASH CODE .....................................................................................................................................................................20 10.11 TEMP. OPTION ...................................................................................................................................................................21 10.12 DIE CLASSIFICATION ...........................................................................................................................................................21 10.13 PIN MODE .......................................................................................................................................................................21 10.14 CONFIGURATION XYZ ..........................................................................................................................................................21 10.15 OPTION ............................................................................................................................................................................21 11 SWISSBIT LABEL SPECIFICATION ................................................................................................................................................22 11.1 FRONT SIDE LASERING ............................................................................................................................................................22 12 REVISION HISTORY .....................................................................................................................................................................23 Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.10 S-200u_data_sheet_SD-NxBN_Rev110.docx Page 4 of 23 3 Product Specification The MICRO SD Memory Card is a small form factor non-volatile memory card which provides high capacity data storage. Its aim is to capture, retain and transport data, audio and images, facilitating the transfer of all types of digital information between a large variety of digital systems. The Card operates in two basic modes:  SD card mode  SPI mode The MICRO SD Memory Card also supports SD High Speed mode with up to 50MHz clock frequency. The cards are compliant with  SD Memory Card Specification Part 1, Physical layer Specification V2.00  SD Memory Card Specification Part 2, File System Specification V2.00  MICRO SD Memory Card Specification V1.10 The Card has an internal intelligent controller which manages interface protocols, data storage and retrieval as well as hardware RS-code Error Correction Code (ECC), defect handling, diagnostics and clock control. The wear leveling mechanism assures an equal usage of the Flash memory cells to extend the life time. The hardware RS-code ECC allows to detect and correct 4 symbols per 528 Bytes. The Card has a voltage detector and a powerful power-loss management feature to prevent data corruption after power-down. The power consumption is very low. The cards are offered in 2 temperature ranges  Extended -25°C…85°C  Industrial -40…85°C The cards are RoHS compliant and lead-free. 3.1 System Performance Table 3: Performance System Performance (3) Burst Data transfer Rate (max clock 50MHz) Sustained Sequential Read 512MB…2GB Sustained Sequential Write 512MB…2GB Sustained Sequential Read 512MB…2GB Sustained Sequential Write 512MB…2GB 1. 2. 3. Firmware Typ. “6” “6” “1”-“5” “1”-“5” 19 (1)(2) 15 (1)(2) 18 (1)(2) 7 Max. (3) 25 21 18 21 10 (1)(2) Unit MB/s All values refer to Toshiba Flash 4Gb 512 MB MICRO SD Memory Card in SD mode 50MHz, cycle time 20ns, write/read file sequential. Sustained Speed measured with SanDisk Mobile mate USB-SD Memory Card reader. It depends on burst speed, flash type and number, and file size In cards configured as “low speed type” (Partnumber Extendsion “-xx2” the high speed mode is disabled (max 25MHz, max 12.5MB/s) 3.2 Environmental Specifications 3.2.1 Recommended Operating Conditions Table 4: MICRO SD Memory Card Recommended Operating Conditions Parameter Extended Operating Temperature Industrial Operating Temperature Power Supply VCC (3.3V) min -25 -40 2.7 typ 25 25 3.3 max 85 85 3.6 unit °C °C V Table 5: Current consumption Current Consumption (type) Write Read Sleep Mode Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland typ 40 30 0.2 max 50 50 0.4 Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Unit mA Revision: 1.10 S-200u_data_sheet_SD-NxBN_Rev110.docx Page 5 of 23 3.2.2 Recommended Storage Conditions Table 6: MICRO SD Memory Card Recommended Storage Conditions Parameter min Extended Storage Temperature Industrial Storage Temperature -40 -40 typ max unit 25 25 85 100 °C °C 3.2.3 Humidity & ESD Table 7: Humidity & ESD Parameter Humidity (non-condensing) Operating Non Operating operation: 95%@25°C storage: 93%@40°C 500h Non Contact Pads area: Contact Pads: ±8 kV (coupling plane ±4 kV, Human body model discharge) according to IEC61000-4-2 ±15 kV (air discharge) Human body model according to IEC61000-4-2 ESD according to IEC61000-4-2 Human body model ±4 kV 100 pF/1.5 kOhm Machine model ±0.25 kV 200 pF/0 Ohm 3.2.4 Durability Table 8: Durability Parameter UV light Exposure Insertions Drop test Bending Torque Shock Vibration (peak -to-peak) Mechanical Schock (target spec.) Operating Non Operating UV: 254nm, 15Ws/cm2 according to ISO7816-1 10,000 office environment 1.5m free fall 10N 0.10Nm ±2.5° max typ. 50g acceleration IEC 512-4-6c typ. 2g in connector IEC 512-4-6d 1500G, 0,5ms, half sine wave ±xyz-axis, five pulses each Non operating, JESD22B110 Condition B 50G, 1.5mm p-p, 20..2000Hz, sweep xyz-axis, five pulses each, Non operating MIL-STD-883 M2007.3 Condition B Vibration (target spec.) 3.3 Physical Dimensions Table 9: Physical Dimensions Outer Physical Dimensions Length Width Thickness Weight (typ.) Unit Value 15.0±0.1 11.0±0.1 0.7 (1.0)±0.1 0.4 mm g 3.4 Reliability Table 10: Reliability Parameter Data Retention Value 10 years (JEDEC47G) 4 Capacity specification Table 11: MICRO SD Memory Card capacity specification Capacity 512MB 1GB 2GB Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Sectors 998’912 2,001,920 4,016,128 Total addressable capacity (Byte) 511’442’944 1,024,983,040 2,056,257,536 Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.10 S-200u_data_sheet_SD-NxBN_Rev110.docx Page 6 of 23 5 Card physical 5.1 Physical description The MICRO SD Memory Card contains a single chip controller and Flash memory module(s). The controller interfaces with a host system allowing data to be written to and read from the Flash memory module(s). Figure 2 and Figure 2 show card dimensions. Figure 1: Mechanical Dimensions MICRO SD Memory Card (simplified) Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Figure 2: Mechanical Dimensions MICRO SD Memory Card (bottom side with connector) Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.10 S-200u_data_sheet_SD-NxBN_Rev110.docx Page 7 of 23 6 Electrical interface 6.1 Electrical description Figure 3: MICRO SD Memory Card Block Diagram Figure 4: MICRO SD Memory Card Shape and Interface (Bottom View) Table 12: MICRO SD Memory Card Pad Assignment Pin # SD Mode SPI Mode Name Type1 Description Name Type1 Description 1 DAT25 I/O/PP Data Line [Bit 2] RSV 2 CD/DAT32 I/O/PP3 Card Detect/ Data Line [Bit 3] CS I3 Chip Select (negative true) 3 CMD PP Command/Response DI I Data In 4 VDD S Supply voltage VDD S Supply voltage 5 CLK I Clock SCLK I Clock 6 VSS S Supply voltage ground VSS S Supply voltage ground 7 DAT0 I/O/PP Data Line [Bit 0] DO O/PP Data Out 8 DAT14 I/O/PP Data Line [Bit 1] RSV Notes: 1) S: power supply; I: input; O: output using push-pull drivers; PP: I/O using push-pull drivers; 2) The extended DAT lines (DAT1-DAT3) are input on power up. They start to operate as DAT lines after SET_BUS_WIDTH command. The Host shall keep its own DAT1-DAT3 lines in input mode, as well, while they are not used. 3) At power up this line has a 50kOhm pull up enabled in the card. This resistor serves two functions Card detection and Mode Selection. For Mode Selection, the host can drive the line high or let it be pulled high to select SD mode. If the host wants to select SPI mode it should drive the line low. For Card detection, the host detects that the line is pulled high. This pull-up should be disconnected by the user, during regular data transfer, with SET_CLR_CARD_DETECT (ACMD42) command 4) DAT1 line may be used as Interrupt Output (from the Card) in SDIO mode during all the times that it is not in use for data transfer operations (refer to "SDIO Card Specification" for further details). 5) DAT2 line may be used as Read Wait signal in SDIO mode (refer to "SDIO Card Specification" for further details). Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.10 S-200u_data_sheet_SD-NxBN_Rev110.docx Page 8 of 23 6.2 DC characteristics Measurements are at Recommended Operating Conditions unless otherwise specified. Table 13: DC Characteristics Symbol Parameter min typ max Peak Voltage on all Lines -0.3 VDD+0.3 VIL Input LOW Voltage -0.3 0.25*VDD VIH Input HIGH Voltage 0.625*VDD VDD+0.3 VOL Output LOW Voltage 0.125*VDD VOH Output HIGH Voltage 0.75*VDD Operating Current 35 50 IDD Pre-initialization Standby Current 3 Post-initialization Standby Current 100 200 ILI Input Leakage Current -10 10 ILO Output Leakage Current -10 10 Table 14: MICRO SD Memory Card Recommended Operating Conditions Symbol Parameter min Normal Operating Status 2.7 VDD Supply Voltage Basic Communication 2.0 (CMD0, CMD15, CMD55, ACMD41) Power Up Time (from 0V to VDD min) unit V V V V V mA mA µA µA µA notes at 100µA at 100µA without pull up R typ max 3.6 unit V 3.3 3.6 V 250 ms 6.3 Signal Loading The total capacitance CL is the sum of the bus master capacitance CHOST, the bus capacitance CBUS, and the capacitance CCARD of the card connected to the line: CL = CHOST + CBUS + CCARD To allow the sum of the host and bus capacitances to be up to 20pF for the card, the following conditions in the table below are met by the card. Table 15: Signal loading Parameter Pull up resistance Pull up resistance Bus signal line capacitance Signal card capacitance Signal line inductance Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Symbol RCMD RDAT CL Ccard Min 10 10 Max 100 100 40 10 16 Unit kOhm kOhm pF pF nH Notes To prevent bus floating To prevent bus floating Single card Single card f≤20MHz Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.10 S-200u_data_sheet_SD-NxBN_Rev110.docx Page 9 of 23 Figure 5: Signal Loading (MICRO SD Memory Card has no WP slider) 6.4 AC characteristics Table 16: AC Characteristics Low Speed Mode Parameter Symbol Min Max Unit Notes CL≤100pF Clock frequency in data transfer mode fPP 0 25 MHz CL≤250pF Clock frequency in card id mode fOD 0 400 KHz Clock low time tWL 10/50 ns Clock high time tWH 10/50 ns CL≤100/250pF Clock rise time tTLH 10/50 ns Clock fall time tTHL 10/50 ns CMD, DAT input setup time tISU 5 ns CL≤25pF CMD, DAT input hold time tIH 5 ns CL≤25pF, data transfer CMD, DAT output delay time tODLY 0 14 ns CL≤25pF, identification CMD, DAT output delay time tODLY 0 50 ns Notes 1. Rise and fall times are measured from 10% to 90% of voltage level. 2. CLK referenced to VIH min and VIL max. 3. CMD and DAT inputs and outputs referenced to CLK. 4. 0Hz means to stop the clock. The given minimum frequency range is for cases where a continuous clock is required 5. Specified for one card Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.10 S-200u_data_sheet_SD-NxBN_Rev110.docx Page 10 of 23 Figure 6: AC Characteristics Low Speed Mode Table 17: AC Characteristics High Speed Mode Parameter Symbol Min Max Unit Notes Clock frequency in data transfer mode fPP 0 50 MHz Clock low time tWL 7.0 ns Clock high time tWH 7.0 ns Clock rise time tTLH 3 ns Clock fall time tTHL 3 ns CL≤10pF CMD, DAT input setup time tISU 6 ns CMD, DAT input hold time tIH 2 ns CMD, DAT output delay time during data tODLY 14 ns transfer mode CMD, DAT output hold time tOH 2.5 ns Notes 1. Rise and fall times are measured from 10% to 90% of voltage level. 2. CLK referenced to VIH min and VIL max. 3. CMD and DAT inputs and outputs referenced to CLK. 4. In order to satisfy severe timing, the host shall drive only one card with max 40pF total at each line. Figure 7: AC Characteristics High Speed Mode Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.10 S-200u_data_sheet_SD-NxBN_Rev110.docx Page 11 of 23 7 Host access Specification The following chapters summarize how the host accesses the card:  Chapter 7.1 summarizes the SD and SPI buses.  Chapter 7.2 summarizes the registers. 7.1 SD and SPI Bus Modes The card supports SD and the SPI Bus modes. Application can chose either one of the modes. Mode selection is transparent to the host. The card automatically detects the mode of the reset command and will expect all further communication to be in the same communication mode. The SD mode uses a 4-bit high performance data transfer, and the SPI mode provides compatible interface to MMC host systems with little redesign, but with a lower performance. 7.1.1 SD Bus Mode Protocol The SD Bus mode has a single master (host) and multiple slaves (cards) synchronous topology. Clock, power, and ground signals are common to all cards. After power up, the SD Bus mode uses DAT0 only; after initialization, the host can change the cards’ bus width from 1 bit (DAT0) to 4 bits (DAT0-DAT3). In high speed mode, only one card can be connected to the bus. Communication over the SD bus is based on command and data bit streams which are initiated by a start bit and terminated by a stop bit.  Command: a command is a token which starts an operation. A command is sent from the host either to a single card (addressed command) or to all connected cards (broadcast command). A command is transferred serially on the CMD line.  Response: a response is a token which is sent from an addressed card, or (synchronously) from all connected cards, to the host as an answer to a previously received command. A response is transferred serially on the CMD line.  Data: data can be transferred from the card to the host or vice versa. Data is transferred via the data lines. The SD bus signals are listed in Table 18, and the SD bus topology is illustrated in Figure 8: SD Bus Topology. Table 18: SD Bus Signals Signal Description CLK Host to card clock signal CMD Bidirectional Command/Response signal DAT0-DAT3 4 Bidirectional data signals Vdd, Vss Power and Ground Figure 8: SD Bus Topology Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.10 S-200u_data_sheet_SD-NxBN_Rev110.docx Page 12 of 23 7.1.2 SPI Bus Mode Protocol The Serial Parallel Interface (SPI) Bus is a general purpose synchronous serial interface. The SPI mode consists of a secondary communication protocol. The interface is selected during the first reset command after power up (CMD0) and it cannot be changed once the card is powered on. While the SD channel is based on command and data bit streams which are initiated by a start bit and terminated by a stop bit, the SPI channel is byte oriented. Every command or data block is built of 8-bit bytes and is byte aligned to the CS signal. The card identification and addressing methods are replaced by a hardware Chip Select (CS) signal. There are no broadcast commands. For every command, a card (slave) is selected by asserting (active low) the CS signal. The CS signal must be continuously active for the duration of the SPI transaction (command, response and data). The only exception occurs during card programming, when the host can de-assert the CS signal without affecting the programming process. The bidirectional CMD and DAT lines are replaced by unidirectional dataIn and dataOut signals. The SPI bus signals are listed Table 19 and the SPI bus topology is illustrated in Figure 9. Table 19: SPI Bus Signals Signal Description /CS Host to card chip select CLK Host to card clock signal Data In Host to card data signal Data Out Card to host data signal Vdd, Vss Power and ground Figure 9: SPI bus topology 7.1.3 Mode Selection The SD Memory Card wakes up in the SD mode. It will enter SPI mode if the CS signal is asserted (negative) during the reception of the reset command (CMD0) and the card is in idle_state. If the card recognizes that the SD mode is required it will not respond to the command and remain in the SD mode. If SPI mode is required the card will switch to SPI and respond with the SPI mode R1 response. The only way to return to the SD mode is by entering the power cycle. In SPI mode the SD Memory Card protocol state machine is not observed. All the SD Memory Card commands supported in SPI mode are always available. During the initialization sequence, if the host gets Illegal Command indication for ACMD41 sent to the card, it may assume that the card is Multimedia Card. In that case it should re-start the card as Multimedia Card using CMD0 and CMD1. Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.10 S-200u_data_sheet_SD-NxBN_Rev110.docx Page 13 of 23 7.2 Card Registers The MICRO SD Memory Card has five registers. Refer to Table 20 to Table 25 for detail. Table 20: MICRO SD Memory Card registers Register Bit Description Function Name Width Card Identification This register contains the card identification information used during the CID 128 information Card Identification phase. Operation This register describes the operating voltage range and contains the status OCR 32 Conditions Registers bit in the power supply. Card specific This register provides information on how to access the card content. Some CSD 128 information fields of this register are writeable by PROGRAM_CSD (CMD27). SD Memory Card’s SCR 64 This register provides information on special features. Special features Relative Card RCA 16 This register carries the card address is SD Memory Card mode. Address Table 21: CID register Register Name MID OID PNM Bit Width 8 16 40 typ. value 0x5d 0x5342 “NgBNc” g=generation c=number of channels 0xgg PRV 8 Product Revision PSN — MDT CRC — 32 4 12 7 1 Product Serial Number Reserved Manufacture Date Check sum of CID contents Not used; always=1 Table 22: OCR register OCR bit position VDD voltage window 0-3 Reserved 4 1.6-1.7 5 1.7-1.8 6 1.8-1.9 7 1.9-2.0 8 2.0-2.1 9 2.1-2.2 10 2.2-2.3 11 2.3-2.4 12 2.4-2.5 13 2.5-2.6 14 Notes 1. 2. Description Manufacture ID OEM/Application ID Product Name 2.6-2.7 typ. value OCR bit position 0 0 0 0 0 0 0 0 0 0 0 15 16 17 18 19 20 21 22 23 24-30 30 0 31 xxxxxxxx 0x0 0xyym chksum 1 VDD voltage window 2.7-2.8 2.8-2.9 2.9-3.0 3.0-3.1 3.1-3.2 3.2-3.3 3.3-3.4 3.4-3.5 3.5-3.6 Reserved Card Capacity Status (CCS) 0=busy; 1=ready typ. value 1 1 1 1 1 1 1 1 1 *1) *2) This bit is valid only when the card power up status bit is set. This bit is set to LOW if the card has not finished the power up routine. Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.10 S-200u_data_sheet_SD-NxBN_Rev110.docx Page 14 of 23 Table 23: CSD register Register Name First Bit Bit Width Description CSD_STRUCTURE 127 2 CSD structure — 125 6 Reserved TAAC 119 8 Data read access time 1 NSAC 111 8 Data read access time 2 (CLK cycle) TRAN_SPEED 103 8 Data transfer rate CCC 95 12 Card command classes READ_BL_LEN 83 4 Read data block length READ_BL_PARTIAL 79 1 Partial blocks for read allowed WRITE_BLK_MISALIGN 78 1 Write block misalignment READ_BLK_MISALIGN 77 1 Read block misalignment DSR_IMP 76 1 DSR implemented — 75 2 Reserved C_SIZE 73 12 Device size VDD_R_CURR_MIN 61 3 VDD min read current VDD_R_CURR_MAX 58 3 VDD max read current VDD_W_CURR_MIN 55 3 VDD min write current VDD_W_CURR_MAX 52 3 VDD max write current C_SIZE_MULT 49 3 Device size multiplier ERASE_BLK_EN 46 1 Erase single block enable SECTOR_SIZE 45 7 Erase sector size WP_GRP_SIZE 38 7 Write protect group size WP_GRP_ENABLE 31 1 Write protect group enable — 30 2 Reserved R2W_FACTOR 28 3 Write speed factor WRITE_BL_LEN 25 4 Write data block length WRITE_BL_PARTIAL 21 1 Partial blocks for write allowed — 20 5 Reserved FILE_FORMAT_GRP 15 1 File format group COPY 14 1 Copy flag PERM_WRITE_PROTECT 13 1 Permanent write protection TMP_WRITE_PROTECT 12 1 Temporary write protection FILE_FORMAT 11 2 File format — 9 2 Reserved CRC 7 7 Checksum of CSD contents — 0 1 Always=1 *) Drive Size and block sizes vary with card capacity ≤2Gb memory capacity = BLOCKNR * BLOCK_LEN Where BLOCKNR = (C_SIZE+1) * MULT MULT = 2C_SIZE_MULT+2 (C_SIZE_MULT < 8) BLOCK_LEN = 2READ_BL_LEN, (READ_BL_LEN < 12) W W(1) typ. Value 00 000000 00001110 00000000 00110010 010110110101 1001 1 0 0 0 00 xxx*) 110 110 110 110 111*) 1 1111111 0000011*) 0 00 100 1001*) 0 00000 0 W(1) 0 W(1) 0 W(1) 0W 00 W(1) 00 W xxxxxxx W 1 value can be changed with CMD27 (PROGRAM_CSD) value can be changed ONCE with CMD27 (PROGRAM_CSD) Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.10 S-200u_data_sheet_SD-NxBN_Rev110.docx Page 15 of 23 Table 24: SCR register Field SCR_STRUCTURE SD_SPEC DATA_STAT_AFTER_ERASE SD_SECURITY SD_BUS_WIDTHS Reserved Reserved Bit Width 4 4 1 3 4 16 32 Table 25: RCA register Field Bit Width RCA 16 *) After Initialization the card can change the RCA register. Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland typ Value 0000 0010 1 011 0101 0 0 typ Value 0x0000*) Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.10 S-200u_data_sheet_SD-NxBN_Rev110.docx Page 16 of 23 8 Declaration of Conformity We Manufacturer: Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland declare under our sole responsibility that the product Product Type: Brand Name: Product Series: Part Number: MICRO SD Memory Card SWISSMEMORY™ MICRO SD Memory Card S-200u SFSDxxxxNxBNxxx-x-xx-xxx-xxx to which this declaration relates is in conformity with the following directives: EN55022:2006 class B IEC61000-4-2: 2001 EN61000-6-2: 2005 IEC61000-4-3: 2006 2002/96/EC Category 3 (WEEE) following the provisions of Directive Electromagnetic compatibility 2004/108/EC Restriction of the use of certain hazardous substances 2011/65/EU Swissbit AG, June 2013 Manuela Kögel Head of Quality Management Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.10 S-200u_data_sheet_SD-NxBN_Rev110.docx Page 17 of 23 9 RoHS and WEEE update from Swissbit Dear Valued Customer, We at Swissbit place great value on the environment and thus pay close attention to the diverse aspects of manufacturing environmentally and health friendly products. The European Parliament and the Council of the European Union have published two Directives defining a European standard for environmental protection. This states that CompactFlash Cards must comply with both Directives in order for them to be sold on the European market:  RoHS – Restriction of Hazardous Substances  WEEE – Waste Electrical and Electronic Equipment Swissbit would like to take this opportunity to inform our customers about the measures we have implemented to adapt all our products to the European norms. What is the WEEE Directive (2002/96/EC)? The Directive covers the following points:    Prevention of WEEE Recovery, recycling and other measures leading to a minimization of wastage of electronic and electrical equipment Improvement in the quality of environmental performance of all operators involved in the EEE life cycle, as well as measures to incorporate those involved at the EEE waste disposal points What are the key elements? The WEEE Directive covers the following responsibilities on the part of producers: Producers must draft a disposal or recovery scheme to dispose of EEE correctly. Producers must be registered as producers in the country in which they distribute the goods. They must also supply and publish information about the EEE categories. Producers are obliged to finance the collection, treatment and disposal of WEEE. Inclusion of WEEE logos on devices In reference to the Directive, the WEEE logo must be printed directly on all devices that have sufficient space. «In exceptional cases where this is necessary because of the size of the product, the symbol of the WEEE Directive shall be printed on the packaging, on the instructions of use and on the warranty» (WEEE Directive 2002/96/EC) When does the WEEE Directive take effect? The Directive came into effect internationally on 13 August, 2005. What is RoHS (2002/95/EC)? The goals of the Directive are to:   Place less of a burden on human health and to protect the environment by restricting the use of hazardous substances in new electrical and electronic devices To support the WEEE Directive (see above) RoHS enforces the restriction of the following 6 hazardous substances in electronic and electrical devices:      Lead (Pb) – no more than 0.1% by weight in homogeneous materials Mercury (Hg) – no more than 0.1% by weight in homogeneous materials Cadmium (Cd) – no more than 0.01% by weight in homogeneous materials Chromium (Cr6+) – no more than 0.1% by weight in homogeneous materials PBB, PBDE – no more than 0.1% by weight in homogeneous materials Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.10 S-200u_data_sheet_SD-NxBN_Rev110.docx Page 18 of 23 Swissbit is obliged to minimize the hazardous substances in the products. According to part of the Directive, manufacturers are obliged to make a self-declaration for all devices with RoHS. Swissbit carried out intensive tests to comply with the self-declaration. We have also already taken steps to have the analyses of the individual components guaranteed by third-party companies. Swissbit carried out the following steps during the year with the goal of offering our customers products that are fully compliant with the RoHS Directive.  Preparing all far-reaching directives, logistical enhancements and alternatives regarding the full understanding and introduction of the RoHS Directive’s standards  Checking the components and raw materials: o o   Replacing non-RoHS-compliant components and raw materials in the supply chain Cooperating closely with suppliers regarding the certification of all components and raw materials used by Swissbit Modifying the manufacturing processes and procedures o Successfully adapting and optimizing the new management-free integration process in the supply chain o Updating existing production procedures and introducing the new procedures to support the integration process and the sorting of materials Carrying out the quality process o Performing detailed function and safety tests to ensure the continuous high quality of the Swissbit product line When does the RoHS Directive take effect? As of 1 July, 2006, only new electrical and electronic devices with approved quantities of RoHS will be put on the market. When will Swissbit be offering RoHS-approved products? Swissbit’s RoHS-approved products are available now. Please contact your Swissbit contact person to find out more about exchanging your existing products for RoHS-compliant devices. For your attention We understand that packaging and accessories are not EEE material and are therefore not subject to the WEEE or RoHS Directives. Contact details: Swissbit AG Industriestrasse 4 CH 9552 Bronschhofen Tel: +41 71 913 03 03 – Fax: +41 71 913 03 15 E-mail: info@swissbit.com – Website: www.swissbit.com Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.10 S-200u_data_sheet_SD-NxBN_Rev110.docx Page 19 of 23 10 Part Number Decoder S F SD 1 2 3 0512 N 4 5 1 B N 1 6 7 8 9 Manuf. Memory Type. Product Type Capacity Platform Generation Memory Organization TO - I 10 11 - M 12 E - 151 - STD 13 14 15 Option Configuration Manuf. Code: Flash Mode Manuf. Code: Flash Package Temp. Option Flash vendor Code Number of flash chips/channels Technology 10.1 Manufacturer Swissbit code S Flash F 10.2 Memory Type 10.3 Product Type SD Memory Card SD 10.4 Capacity 512MByte 1 GByte 2 GByte 0512 1024 2048 10.5 Platform MICRO SD Memory Card N 10.6 Generation 10.7 Memory Organization x8 B 10.8 Technology SD Memory Card controller S-2x0 series N 10.9 Channels 1 Flash Channel 2 Flash Channel 1 2 10.10 Flash Code Micron Toshiba Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland MT TO Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.10 S-200u_data_sheet_SD-NxBN_Rev110.docx Page 20 of 23 10.11 Temp. Option Industrial Temp. Range -40°C – 85°C Extended Temp. Range -25°C – 85°C I E 10.12 DIE Classification SLC MONO (single die package) SLC DDP (dual die package) SLC QDP (quad die package) M D Q 10.13 PIN Mode Single nCE & R/nB Dual nCE & Dual R/nB 0/E 1/F 10.14 Configuration XYZ X Configuration Configuration default X 1 Y  FW Revision FW Revision Revision 1 (080916) Revision 2 (090306) Revision 3 (091030) Revision 4 (100107) Revision 5 (101201) Revision 6 (120514) Y 1 2 3 4 5 6 Z  optional Optional default Low Speed Z 1 2 10.15 Option Swissbit / Standard Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland STD Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.10 S-200u_data_sheet_SD-NxBN_Rev110.docx Page 21 of 23 11 Swissbit Label specification 11.1 Front side printing swissbit Manufacturer 2GB Logo Density MICRO SD Memory Card logo 11.2 Back side lasering Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland SFSD2048N1BN1 TO-I-QF-161-STD Partnumber CWYY 60XXXXXX Date Position Lot Code Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.10 S-200u_data_sheet_SD-NxBN_Rev110.docx Page 22 of 23 Revision History Table 26: Document Revision History Date 08-March-2011 17-February-2012 18-June-2012 28-August-2012 31-August-2012 04-February-2013 03-June-2013 Revision Revision Details 1.00 Initial Release 1.01 Performance value updated, PN update of FW version 1.02 SDA Correction, FW-Rev. 6 correction 1.03 1GB capacity corrected, design guide update 1.04 Speed values for Firmware “6” and “1”-“5”, Low speed cards 1.05 Added Mechanical Shock and Vibration Test results New product pictures, new CE Declaration 1.10 Add 2GB type, update front printing and back lasering, no extra solder pads Disclaimer: No part of this document may be copied or reproduced in any form or by any means, or transferred to any third party, without the prior written consent of an authorized representative of Swissbit AG (“SWISSBIT”). The information in this document is subject to change without notice. SWISSBIT assumes no responsibility for any errors or omissions that may appear in this document, and disclaims responsibility for any consequences resulting from the use of the information set forth herein. SWISSBIT makes no commitments to update or to keep current information contained in this document. The products listed in this document are not suitable for use in applications such as, but not limited to, aircraft control systems, aerospace equipment, submarine cables, nuclear reactor control systems and life support systems. Moreover, SWISSBIT does not recommend or approve the use of any of its products in life support devices or systems or in any application where failure could result in injury or death. If a customer wishes to use SWISSBIT products in applications not intended by SWISSBIT, said customer must contact an authorized SWISSBIT representative to determine SWISSBIT willingness to support a given application. The information set forth in this document does not convey any license under the copyrights, patent rights, trademarks or other intellectual property rights claimed and owned by SWISSBIT. The information set forth in this document is considered to be “Proprietary” and “Confidential” property owned by SWISSBIT. ALL PRODUCTS SOLD BY SWISSBIT ARE COVERED BY THE PROVISIONS APPEARING IN SWISSBIT’S TERMS AND CONDITIONS OF SALE ONLY, INCLUDING THE LIMITATIONS OF LIABILITY, WARRANTY AND INFRINGEMENT PROVISIONS. SWISSBIT MAKES NO WARRANTIES OF ANY KIND, EXPRESS, STATUTORY, IMPLIED OR OTHERWISE, REGARDING INFORMATION SET FORTH HEREIN OR REGARDING THE FREEDOM OF THE DESCRIBED PRODUCTS FROM INTELLECTUAL PROPERTY INFRINGEMENT, AND EXPRESSLY DISCLAIMS ANY SUCH WARRANTIES INCLUDING WITHOUT LIMITATION ANY EXPRESS, STATUTORY OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. ©2013 SWISSBIT AG All rights reserved. Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.10 S-200u_data_sheet_SD-NxBN_Rev110.docx Page 23 of 23