74LCX14 Low voltage CMOS HEX SCHMITT inverter with 5V tolerant inputs Features ■ 5V tolerant inputs ■ High speed: – tPD = 5.0ns (Max) at VCC = 3V ■ Power down protection on inputs and outputs ■ Symmetrical output impedance: – |IOH| = IOL = 24mA (Min) at VCC = 3V ■ PCI bus levels guaranteed at 24mA ■ Balanced propagation delays: – tPLH ≅ tPHL r P e t e l o ■ Pin and function compatible with 74 series 14 ■ Latch-up performance exceeds 500mA (JESD 17) ■ ESD performance: – HBM > 2000V (MIL STD 883 method 3015); MM > 200V let o s b TSSOP14 Description Operating voltage range: – VCC (Opr) = 2.0V to 3.6V r P e u d o SO-14 ■ ) (s t c u od ) s ( ct The 74LCX14 is a low voltage CMOS HEX SCHMITT inverter fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS technology. It is ideal for low power and high speed 3.3V applications. It can be interfaced to 5V signal environment for inputs. s b O It has same speed performance at 3.3V than 5V AC/ACT family, combined with a lower power consumption. Pin configuration and function are the same as those of the 74LCX04 but the 74LCX14 has hysteresis between the positive and negative input threshold typically of 0.8V. This together with its schmitt trigger function allows it to be used on line receivers with slow rise/fall input signals. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. O Order codes July 2006 Part number Package Packaging 74LCX14MTR SO-14 Tape and reel 74LCX14TTR TSSOP14 Tape and reel Rev 6 1/15 www.st.com 15 Contents 74LCX14 Contents 1 Logic symbols and I/O equivalent circuit . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Pin settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 2.1 Pin connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.3 Truth table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ) s ( ct Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.1 u d o Recommended operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 r P e 4 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5 Test circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 6 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 7 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 8 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 t e l o ) (s t c u d o r P e t e l o s b O 2/15 s b O 74LCX14 1 Logic symbols and I/O equivalent circuit Logic symbols and I/O equivalent circuit Figure 1. IEC logic symbols ) s ( ct u d o Figure 2. Input and output equivalent circuit r P e t e l o ) (s s b O t c u d o r P e t e l o s b O 3/15 Pin settings 74LCX14 2 Pin settings 2.1 Pin connection Figure 3. Pin connection (top through view) ) s ( ct u d o r P e 2.2 t e l o Pin description Table 1. Pin description Pin N° s ( t c 1, 3, 5, 9, 11, 13 2, 4, 6, 8, 10, 12 u d o 7 Pr 14 Name and function 1A to 6A Data inputs 1Y to 6Y Data outputs GND Ground (0V) VCC Positive supply voltage e table t Truth e ol 2.3 s b O 4/15 )- Symbol s b O Table 2. Truth table Inputs Output A Y L H H L 74LCX14 3 Maximum rating Maximum rating stressing the device above the rating listed in the “absolute maximum ratings” table may cause permanent damage to the device. these are stress ratings only and operation of the device at these or any other conditions above those indicated in the operating sections of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. refer also to the STMicroelectronics sure program and other relevant quality documents. Table 3. Absolute maximum ratings Symbol VCC Parameter Value Unit Supply voltage -0.5 to +7.0 VI DC input voltage -0.5 to +7.0 VO DC output voltage (VCC = 0V) -0.5 to +7.0 VO DC output voltage (high or low state) (1) IIK DC input diode current IOK DC output diode current (2) IO DC output current ICC DC supply current per supply pin IGND DC ground current per supply pin Tstg Storage temperature TL ) (s Lead temperature (10 sec) (s) ct du ete ol s b O V V V -0.5 to VCC + 0.5 V -50 mA -50 mA ± 50 mA ± 100 mA ± 100 mA -65 to +150 °C 300 °C Value Unit 2.0 to 3.6 V o r P t c u 1. IO absolute maximum rating must be observed 2. VO < GND 3.1 d o Recommended r operating conditions P e t e l Table 4. Recommended operating conditions O o s b Symbol VCC Parameter Supply voltage (1) VI Input voltage 0 to 5.5 V VO Output voltage (VCC = 0V) 0 to 5.5 V VO Output voltage (high or low state) 0 to VCC V IOH, IOL High or low level output current (VCC = 3.0 to 3.6V) ± 24 mA IOH, IOL High or low level output current (VCC = 2.7V) ± 12 mA -40 to 85 °C Top Operating temperature 1. Truth table guaranteed: 1.5V to 3.6V 5/15 Electrical characteristics 4 74LCX14 Electrical characteristics Table 5. DC specifications Test condition Symbol Parameter -40 to 85°C VCC (V) Min Max Unit VT+ Positive input threshold 3.0 1.2 2.2 V VT- Negative input threshold 3.0 0.6 1.5 V VH Hysteresis voltage 3.0 0.4 1.2 V 2.7 to 3.6 IO=-100 µA 2.7 IO=-12 mA High level output voltage VOH IO=-18 mA 3.0 e t e l IO=-24 mA )- s ( t c ICC e t e ol u d o Power OFF leakage current Pr ∆ICC 2.7 to 3.6 I incr. per Input 2.7 to 3.6 2.2 0.4 IO=16 mA 0.4 IO=24 mA 0.55 VI = 0 to 5.5V ±5 µA VI or VO = 5.5V 10 µA VI = VCC or GND 10 VI or VO= 3.6 to 5.5V ± 10 VIH = VCC - 0.6V 500 0 Quiescent supply current V 2.4 IO=12 mA b O Input leakage current 2.7 to 3.6 Ioff Pr 2.2 0.2 3.0 II u d o VCC-0.2 IO=100 µA 2.7 Low level output voltage VOL ) s ( ct so 2.7 to 3.6 s b O Value V µA µA Table 6. Dynamic switching characteristics Test condition Symbol VOLP VOLV Parameter Dynamic low level quiet output (1) TA = 25 °C VCC (V) 3.3 Value Min CL = 50pF VIL = 0V, VIH = 3.3V Typ Unit Max 0.8 V -0.8 1. Number of outputs defined as "n". Measured with "n-1" outputs switching from HIGH to LOW or LOW to HIGH. The remaining output is measured in the LOW state. 6/15 74LCX14 Electrical characteristics Table 7. AC electrical characteristics Test condition Symbol tPLH tPHL tOSLH tOSHL Parameter VCC (V) Propagation delay time 2.7 Output to output skew time (1) (2) Value CL (pF) RL (Ω) ts = tr (ns) 50 500 2.5 50 500 2.5 3.0 to 3.6 3.0 to 3.6 -40 to 85 °C Min Unit Max 6.5 1.5 5.0 1.0 ns ns 1. Skew is defined as the absolute value of the difference between the actual propagation delay for any two outputs of the same device switching in the same direction, either HIGH or LOW (tOSLH = | tPLHm - tPLHn|, tOSHL = | tPHLm - tPHLn|) ) s ( ct 2. Parameter guaranteed by design u d o Table 8. Capacitive characteristics Test condition Symbol Parameter VCC (V) e t e ol Pr Min Value TA = 25 °C Typ Unit Max CIN Input capacitance 3.3 VIN = 0 to VCC 6 pF CPD Power dissipation capacitance (1) 3.3 fIN = 10MHz VIN = 0 or VCC 48 pF bs O ) 1. CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/6 (per gate) s ( t c u d o r P e t e l o s b O 7/15 Test circuit 5 74LCX14 Test circuit Figure 4. Test circuit u d o CL = 50pF or equivalent (includes jig and probe capacitance) RL = 500Ω or equivalent r P e RT = ZOUT of pulse generator (typically 50Ω) 6 t e l o Waveforms ) (s Figure 5. Waveform - propagation delay (f = 1MHz; 50% duty cycle) t c u d o r P e t e l o s b O 8/15 s b O ) s ( ct 74LCX14 7 Package mechanical data Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second level interconnect . The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com ) s ( ct u d o r P e t e l o ) (s s b O t c u d o r P e t e l o s b O 9/15 Package mechanical data 74LCX14 SO-14 MECHANICAL DATA mm. DIM. MIN. inch TYP MAX. MIN. TYP. MAX. A 1.35 1.75 0.053 0.069 A1 0.1 0.25 0.004 0.010 A2 1.10 1.65 0.043 0.065 B 0.33 0.51 0.013 0.020 C 0.19 0.25 0.007 0.010 D 8.55 8.75 0.337 E 3.8 4.0 0.150 e 0.344 u d o 1.27 0.050 H 5.8 6.2 0.228 h 0.25 0.50 0.010 L 0.4 1.27 k 0° o s b e t e l 8° ddd 0.100 ) s ( ct Pr 0.157 0.244 0.020 0.016 0.050 0° 8° 0.004 O ) s ( t c u d o r P e t e l o s b O 0016019D 10/15 74LCX14 Package mechanical data TSSOP14 MECHANICAL DATA mm. inch DIM. MIN. TYP A MAX. MIN. TYP. MAX. 1.2 A1 0.05 A2 0.8 b 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 c 0.09 0.20 0.004 D 4.9 5 5.1 0.193 E 6.2 6.4 6.6 0.244 E1 4.3 4.4 4.48 0.169 1 e K 0˚ L 0.45 o s b 8˚ 0.60 0.75 0.0089 du 0.197 0.201 ro P e let 0.65 BSC ) s ( ct 0.012 0.252 0.260 0.173 0.176 0.0256 BSC 0˚ 8˚ 0.018 0.024 0.030 O ) A s ( t c A2 r P e u d o A1 b t e l o e K c L E D s b O E1 PIN 1 IDENTIFICATION 1 0080337D 11/15 Package mechanical data 74LCX14 Tape & Reel SO-14 MECHANICAL DATA mm. inch DIM. MIN. TYP A 12.8 13.2 D 20.2 0.795 N 60 2.362 MAX. 0.504 0.519 ) s ( ct 22.4 0.882 Ao 6.4 6.6 0.252 Bo 9 9.2 0.354 Ko 2.1 2.3 0.082 Po 3.9 4.1 0.153 P 7.9 8.1 0.311 t c u d o r P e 12/15 TYP. 12.992 C ) (s s b O MIN. 330 T t e l o MAX. s b O e t e ol 0.260 Pr u d o 0.362 0.090 0.161 0.319 74LCX14 Package mechanical data Tape & Reel TSSOP14 MECHANICAL DATA mm. inch DIM. MIN. TYP A MAX. MIN. TYP. 330 MAX. 13.2 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 0.504 0.519 ) s ( ct 22.4 0.882 Ao 6.7 6.9 0.264 Bo 5.3 5.5 0.209 Ko 1.6 1.8 0.063 Po 3.9 4.1 0.153 P 7.9 8.1 ete 0.311 0.272 o r P du 0.217 0.071 0.161 0.319 l o s ) (s b O t c u d o r P e t e l o s b O 13/15 Revision history 8 74LCX14 Revision history Table 9. Revision history Date Revision Changes 15-Sep-2004 5 Ordering codes revision - pag. 1. 10-Jul-2006 6 New template, temperature ranges updated ) s ( ct u d o r P e t e l o ) (s t c u d o r P e t e l o s b O 14/15 s b O 74LCX14 ) s ( ct Please Read Carefully: u d o Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. r P e t e l o Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. s b O No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. ) (s UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. t c u d o r UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZE REPRESENTATIVE OF ST, ST PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS, WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. P e t e l o Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. s b O ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2006 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 15/15