TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 D D D D D D D D IBM PC/AT  Compatible Two TL16C550 ACEs Enhanced Bidirectional Printer Port 16-Byte FIFOs Reduce CPU Interrupts Up to 16-MHz Clock Rate for up to 1-Mbaud Operation Transmit, Receive, Line Status, and Data Set Interrupts on Each Channel Independently Controlled Individual Modem Control Signals for Each Channel D D Programmable Serial Interface Characteristics for Each Channel: – 5-, 6-, 7-, or 8-Bit Characters – Even, Odd, or No Parity Bit Generation and Detection – 1-, 1-1/2-, or 2-Stop Bit Generation 3-State Outputs Provide TTL Drive for the Data and Control Bus on Each Channel Hardware and Software Compatible With TL16C452 RXRDY0 DCD1 GND RI1 DSR1 CLK CS1 TRI PEMD ACK PE BUSY SLCT VDD ERR SIN1 RXRDY1 HV or FN PACKAGE (TOP VIEW) 9 10 8 7 6 5 4 3 2 1 68 67 66 65 64 63 62 61 60 11 59 12 58 13 57 14 56 15 55 16 54 17 53 18 52 19 51 20 50 21 49 22 48 23 47 24 46 25 45 INT1 INT2 SLIN INIT AFD STB GND PD0 PD1 PD2 PD3 PD4 PD5 PD6 PD7 INT0 BDO TXRDY1 ENIRQ CTS0 DCD0 RI0 DSR0 CS0 A2 A1 A0 IOW IOR CS2 RESET VDD SIN0 44 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 GND SOUT1 DTR1 RTS1 CTS1 DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 TXRDY0 VDD RTS0 DTR0 SOUT0 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. IBM PC/AT is a trademark of International Business Machines Corporation. Copyright  1999, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 BDO NC NC NC INT1 INT2 SLIN INIT AFD STB GND PD0 PD1 PD2 PD3 PD4 PD5 PD6 PD7 INT0 PN PACKAGE (TOP VIEW) 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 1 60 2 59 3 58 4 57 5 56 6 55 7 54 8 53 9 52 10 51 11 50 12 49 13 48 14 47 15 46 16 45 17 44 18 43 19 42 20 41 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 NC ENIRQ TXRDY1 SIN0 VDD RESET CS2 IOR IOW A0 A1 A2 CS0 DSR0 RI0 DCD0 CTS0 GND NC NC NC NC SOUT1 DTR1 RTS1 CTS1 DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 TXRDY0 VDD RTS0 DTR0 SOUT0 NC NC NC RXRDY1 SIN1 ERR VDD SLCT BUSY PE ACK PEMD TRI CS1 CLK DSR1 RI1 GND DCD1 RXRDY0 NC description The TL16C552A is an enhanced dual-channel version of the popular TL16C550B asynchronous communications element (ACE). The device serves two serial input /output interfaces simultaneously in microcomputer or microprocessor-based systems. Each channel performs serial-to-parallel conversion on data characters received from peripheral devices or modems and parallel-to-serial conversion on data characters transmitted by the CPU. The complete status of each channel of the dual ACE can be read at any time during functional operation by the CPU. The information obtained includes the type and condition of the transfer operations being performed and the error conditions encountered. In addition to its dual communications interface capabilities, the TL16C552A provides the user with a bidirectional parallel data port that fully supports the parallel Centronics-type printer interface. The parallel port and the two serial ports provide IBM PC/AT-compatible computers with a single device to serve the three system ports. A programmable baud rate generator that can divide the timing reference clock input by a divisor between 1 and (216 – 1) is included. The TL16C552A is available in a 68-pin plastic-leaded chip-carrier (FN) package and a 80-pin TQFP (PN) package. The TL16C552AM is available in a 68-pin ceramic quad flat (HV) package. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 functional block diagram CTS0 DSR0 DCD0 RI0 SIN0 CS0 DB0 – DB7 28 24 31 25 29 26 ACE #1 30 41 45 9 22 32 14 – 21 RTS0 DTR0 SOUT0 INT0 RXRDY0 TXRDY0 8 8 CTS1 DSR1 DCD1 RI1 SIN1 CS1 A0 – A2 IOW IOR RESET CLK 35 – 33 13 12 5 11 8 10 ACE #2 6 62 60 61 3 42 RTS1 DTR1 SOUT1 INT1 RXRDY1 TXRDY1 3 36 Select and Control Logic 37 39 44 BDO 8 4 8 ERR SLCT BUSY PE ACK PEMD CS2 ENIRQ 53 – 46 63 57 65 56 66 55 67 68 Parallel Port 58 59 PD0 – PD7 INIT AFD STB SLIN INT2 1 38 43 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 Terminal Functions TERMINAL I/O DESCRIPTION 10 I Line printer acknowledge. ACK goes low to indicate a successful data transfer has taken place. ACK generates a printer port interrupt during its positive transition. 56 75 I/O Line printer autofeed. AFD is an open-drain line that provides the printer with an active-low signal when continuous form paper is to be autofed to the printer. AFD has an internal pullup resistor to VDD of approximately 10 kΩ . 35, 34, 33 51, 50, 49 I Address. The address lines A0 – A2 select the internal registers during CPU bus operations. See Table 2 for the decode of the serial channels and Table 13 for the decode of the parallel printer port. BDO 44 63 O Bus buffer. BDO is the active-high output and is asserted when either the serial channel or the parallel port is read. BDO controls the system bus driver (74LS245 or 54LS245). BUSY 66 8 I Line printer busy. BUSY is an input line from the printer that goes high when the printer is not ready to accept data. CLK 4 14 I Clock. CLK is the external clock input to the baud rate divisor of each ACE. CS0, CS1, CS2 32, 3, 38 48, 13, 54 I Chip select. Each CSx input acts as an enable for the write and read signals for serial channels 1 (CS0) and 2 (CS1). CS2 enables the signals to the printer port. CTS0, CTS1 28, 13 44, 26 I Clear to send. The logical state of each CTSx terminal is reflected in the CTS bit of the modem status register (CTS is bit 4 of the modem status register, written as MSR4) of each ACE. A change of state in either CTS terminal since the previous reading of the associated MSR causes the setting of ∆ CTS (MSR0) of each modem status register. DB0 – DB7 14 – 21 27 – 34 I/O Data bits DB0 – DB7. The data bus provides eight I/O lines with 3-state outputs for the transfer of data, control, and status information between the TL16C552A and the CPU. These lines are normally in the high-impedance state except during read operations. DB0 is the least significant bit (LSB) and is the first serial data bit to be received or transmitted. DCD0, DCD1 29, 8 45, 18 I Data carrier detect. DCD is a modem input. Its condition can be tested by the CPU by reading MSR7 (DCD) of the modem status registers. MSR3 (∆ DCD) of the modem status register indicates whether DCD has changed states since the previous reading of the MSR. DCD has no effect on the receiver. DSR0, DSR1 31, 5 47, 15 I Data set ready. The logical state of the DSRx terminals is reflected in MSR5 of its associated modem status register. ∆ DSR (MSR1) indicates whether the associated DSRx terminal has changed states since the previous reading of the MSR. DTR0, DTR1 25, 11 38, 24 O Data terminal ready. Each DTRx can be set low by setting MCR0, modem control register bit 0 of its associated ACE. DTRx is cleared (high) by clearing the DTR bit (MCR0) or whenever a reset occurs. When active (low), DTRx indicates that its ACE is ready to receive data. ENIRQ 43 59 I Parallel port interrupt source mode selection. When ENIRQ is low, the AT mode of interrupts is enabled. In AT mode, INT2 is internally connected to ACK. When ENIRQ is tied high, the PS-2 mode of interrupt is enabled and INT2 is internally tied to the inverse of the PRINT bit in the line printer status register. INT2 is latched high on the rising edge of ACK. INT2 is held until the status register is read, which then clears the PRINT status bit and INT2. ERR 63 5 I Line printer error. ERR is an input line from the printer. The printer reports an error by holding ERR low during the error condition. GND 7, 27, 54 17, 43, 73 INIT 57 76 I/O Line printer initialize. INIT is an open-drain line that provides the printer with an active-low signal that allows the printer initialization routine to be started. INIT has an internal pullup resistor to VDD of approximately 10 kΩ. 45, 60 64, 79 O External serial channel interrupt. Each serial channel interrupt 3-state output (enabled by bit 3 of the MCR) goes active (high) when one of the following interrupts has an active (high) condition and is enabled by the interrupt enable register of its associated channel: receiver error flag, received data available, transmitter holding register empty, and modem status. The interrupt is cleared on appropriate service. Upon reset, the interrupt output is in the high-impedance state. NAME NO. FN PN ACK 68 AFD A0, A1, A2 INT0, INT1 4 Ground (0 V). All terminals must be tied to GND for proper operation. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 Terminal Functions (Continued) TERMINAL I/O DESCRIPTION 78 O Printer port interrupt. INT2 is an active-high, 3-state output generated by the positive transition of ACK. INT2 is enabled by bit 4 of the write control register. Upon reset, INT2 is in the high-impedance state. Its mode is also controlled by ENIRQ. 37 53 I Input /output read strobe. IOR is an active-low input that enables the selected channel to output data to the data bus (DB0 – DB7). The data output depends on the register selected by the address inputs A0, A1, A2, and chip select. Chip select 0 (CS0) selects ACE #1, chip select 1 (CS1) selects ACE #2, and chip select 2 (CS2) selects the printer port. 36 52 I Input/output write strobe. IOW is an active-low input causing data from the data bus to be input to either ACE or to the parallel port. The destination depends on the register selected by the address inputs A0, A1, A2, and chip selects CS0, CS1, and CS2. 53 – 46 72–65 I/O PE 67 9 I Line printer paper empty. PE is an input line from the printer that goes high when the printer runs out of paper. PEMD 1 11 I Printer enhancement mode. When low, PEMD enables the write data register to the PD0 – PD7 lines. A high on PEMD allows direction control of the PD0 – PD7 port by the DIR bit in the control register. PEMD is usually tied low for the printer operation. RESET 39 55 I Reset. When low, RESET forces the TL16C552A into an idle mode in which all serial data activities are suspended. The modem control register and its associated outputs are cleared. The line status register is cleared except for the transmitter holding register empty (THRE) and TEMT bits, which are set. All functions of the device remain in an idle state until programmed to resume serial data activities. RESET has a hysteresis level of typically 400 mV. RTS0, RTS1 24, 12 37, 25 O Request to send. The RTS outputs are set low by setting MCR1 of its UARTs modem control register. Both RTS terminals are reset high by RESET. A low on RTS indicates that its ACE has data ready to transmit. In half-duplex operations, RTS controls the direction of the line. RXRDY0, RXRDY1 9, 61 19, 3 O Receiver ready. Receiver direct memory access (DMA) signaling is also available through this output. One of two types of DMA signaling can be selected using FCR3 when in FIFO mode. Only DMA mode 0 is allowed when in TL16C450 mode. For signal transfer DMA (a transfer is made between CPU bus cycles), mode 0 is used. Multiple transfers that are made continuously until the receiver FIFO has been emptied are supported by mode 1. NAME NO. FN PN INT2 59 IOR IOW PD0 – PD7 Parallel data bits (0 – 7). PD0 – PD7 provide a byte wide input or output port to the system. Mode 0. RXRDY is active (low) in FIFO mode (FCR0 = 1, FCR3 = 0) or in TL16C450 mode (FCR0 = 0) and the receiver FIFO or receiver holding register contains at least one character. When there are no more characters in the FIFO or holding register, RXRDY goes inactive (high). Mode 1. RXRDY goes active (low) in the FIFO mode (FCR0 = 1) when FCR3 = 1 and the time-out or trigger levels have been reached. RXRDY goes inactive (high) when the FIFO or holding register is empty. RI0, RI1 30, 6 46, 16 I Ring indicator. The RI signal is a modem control input. Its condition is tested by reading MSR6 (RI) of each ACE. The modem status register output TERI (MSR2) indicates whether RI has changed from high to low since the previous reading of the modem status register. SIN0, SIN1 41, 62 57, 4 I Serial data. SIN0 and SIN1 move information from the communication line or modem to the TL16C552A receiver circuits. Mark is a high state and space is a low state. Data on serial data inputs is disabled in loop mode. SLCT 65 7 I Line printer select. SLCT is an input line from the printer that goes high when the printer is selected. SLIN 58 77 I/O Line printer select. SLIN is an open-drain I/O that selects the printer when active (low). SLIN has an internal pullup resistor to VDD of approximately 10 kΩ. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 Terminal Functions (Continued) TERMINAL NAME I/O DESCRIPTION 39, 23 O Serial data outputs. SOUT0 and SOUT1 are the serial data outputs from the ACE transmitter circuitry. A mark is a high state and a space is a low state. Each SOUT is held in the mark condition when the transmitter is disabled (RESET is asserted low), the transmitter register is empty, or when in the loop mode. 55 74 I/O Line printer strobe. STB provides communication between the TL16C552A and the printer. When STB is active (low), it provides the printer with a signal to latch the data currently on the parallel port. STB has an internal pullup resistor to VDD of approximately 10 kΩ. 2 12 I 3-state output control input. TRI controls the 3-state control of all I/O and output terminals. When TRI is asserted, all I/Os and outputs are in the high-impedance state, allowing board level testers to drive the outputs without overdriving internal buffers. TRI is level sensitive and is pulled down with an internal resistor that is approximately 5 kΩ . 22, 42 35, 58 O Transmitter ready. Two types of DMA signaling are available. Either can be selected using FCR3 when operating in FIFO mode. Only DMA mode 0 is allowed when in TL16C450 mode. Single-transfer DMA (a transfer is made between CPU bus cycles) is supported by mode 0. Multiple transfers that are made continuously until the transmitter FIFO has been filled are supported by mode 1. NO. FN PN 26, 10 STB TRI SOUT0, SOUT1 TXRDY0 TXRDY1 Mode 0. In FIFO mode (FCR0 = 1, FCR3 = 0) or in TL16C450 mode (FCR0 = 0) when there are no characters in the transmitter holding register or transmitter FIFO, TXRDYx is active (low). Once TXRDYx is activated (low), it goes inactive after the first character is loaded into the holding register of the transmitter FIFO. Mode 1. TXRDY goes active (low) in FIFO mode (FCR0 = 1) when FCR3 = 1 and there are no characters in the transmitter FIFO. When the transmitter FIFO is completely full, TXRDY goes inactive (high). VDD 23, 40, 64 6, 36, 56 Power supply. The VDD requirement is 5 V ± 5%. absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to VDD + 0.3 V Input voltage range, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to 7 V Output voltage range, VO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to VDD + 0.3 V Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Operating free-air temperature range, TA:: I suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 85°C M suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 55°C to 125°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE 1: All voltage levels are with respect to GND. PACKAGE DISSIPATION RATING TABLE‡ TA ≤ 25°C DERATING FACTOR§ TA = 70°C POWER RATING POWER RATING ABOVE TA = 25°C TA = 125°C POWER RATING FN 1730 mW 19.2 mW/° C 865 mW – HV 1689 mW 13.5 mW/° C 1081 mW 337 mW ‡ Power ratings assume a maximum junction temperature (TJ) of 115° C for ’I’ and 150° C for ’M’ suffix devices. § Derating factor is the inverse of the junction-to-ambient thermal resistance, RθJA. 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 recommended operating conditions Supply voltage, VDD MIN NOM MAX UNIT 4.75 5 5.25 V VDD 0.8 V VDD 0.8 V Clock high-level input voltage, VIH(CLK) 2 Clock low-level input voltage, VIL(CLK) 0 High-level input voltage, VIH 2 Low-level input voltage, VIL 0 Clock frequency, fclock Operating free-air free air temperature, temperature TA 16 I suffix – 40 85 M suffix – 55 125 V V MHz °C package thermal characteristics PARAMETER RθJA Junction-to-ambient thermal impedance RθJC Junction-to-case thermal impedance TJ Junction temperature FN Package TEST CONDITIONS MIN TYP Board mounted, no air flow HV Package MAX MIN 52 TYP MAX °C/W 74 14 °C/W 3 115 UNIT 150 °C/W electrical characteristics over recommended ranges of operating free-air temperature and supply voltage (unless otherwise noted) PARAMETER TEST CONDITIONS VOH High-level output voltage IOH = – 12 mA for PD0 – PD7, IOH = – 4 mA for all other outputs (see Note 2), VOL Low-level output voltage IOL = 12 mA for PD0 – PD7, IOL = 12 mA for INIT, AFD, STB, and SLIN, IOL = 4 mA for all other outputs II Input current II(CLK) MIN MAX 2.4 UNIT V 0.4 V VDD = 5.25 V (see Note 3), All other terminals are floating ± 10 µA Clock input current VI = 0 to 5.25 V ± 10 µA IOZ High-impedance High im edance output out ut current VDD = 5 5.25 25 V V, VO = 0 with chip chi deselected or VO = 5 5.25 25 V with chip and write mode selected (see Note 2) ± 20 µA IDD Supply current 5 25 V VDD = 5.25 V, In uts at 0 0.8 V, 8 V or 2 V Inputs 50 mA No loads on outputs, outputs fclock = 8 MHz NOTES: 2. Excluding INIT, AFD, STB, and SLIN. They are open-drain terminals with an internal pullup resistor to VDD of approximately 10 KΩ. 3. Excluding the TRI input terminal. It contains an internal pulldown resistor of approximately 5 kΩ. clock timing requirements over recommended ranges of operating free-air temperature and supply voltage MIN MAX UNIT tw1 tw2 Pulse duration, CLK ↑ (external clock) (see Figure 1) 31 ns Pulse duration, CLK ↓ (external clock) (see Figure 1) 31 ns tw3 Pulse duration, RESET 1000 ns POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 read cycle timing requirements over recommended ranges of operating free-air temperature and supply voltage (see Note 4 and Figure 4) MIN MAX UNIT tw4 tsu1 Pulse duration, IOR ↓ 80 ns Setup time, CSx valid before IOR ↓ (see Note 5) 15 ns tsu2 th1 Setup time, A2 – A0 valid before IOR ↓ (see Note 5) 15 ns Hold time, A2 – A0 valid after IOR ↑ (see Note 5) 20 ns th2 td1 Hold time, CSx valid after IOR ↑ (see Note 5) 20 ns Delay time, tsu2 + tw4 + td2 (see Note 6) 175 ns td2 Delay time, IOR ↑ to IOR or IOW ↓ 80 ns NOTES: 4. These parameters are not production tested. 5. The internal address strobe is always active. 6. In FIFO mode, td1 = 425 ns (min) between reads of the receiver FIFO and the status registers (interrupt identification register and line status register). write cycle timing requirements over recommended ranges of operating free-air temperature and supply voltage (see Note 7 and Figure 5) MIN MAX UNIT tw5 tsu4 Pulse duration, IOW ↓ 80 ns Setup time, CSx valid before IOW ↓ (see Note 8) 15 ns tsu5 tsu6 Setup time, A2 – A0 valid before IOW ↓ (see Note 8) 15 ns Setup time, DB0 – DB7 valid before IOW ↑ 15 ns th3 th4 Hold time, A2 – A0 valid after IOW ↑ (see Note 8) 20 ns Hold time, CSx valid after IOW ↑ (see Note 8) 20 ns th5 td3 Hold time, DB0 – DB7 valid after IOW ↑ Delay time, tsu5 + tw5 + td4 td4 Delay time, IOW ↑ to IOW or IOR ↓ NOTES: 7. These parameters are not production tested. 8. The internal address strobe is always active. 15 ns 175 ns 80 ns read cycle switching characteristics over recommended ranges of operating free-air temperature and supply voltage, CL = 100 pF (see Note 9 and Figure 4) PARAMETER tpd1 ten MIN UNIT Propagation delay time from IOR ↓ to BDO ↑ or from IOR ↑ to BDO ↓ 60 ns Enable time from IOR ↓ to DB0 – DB7 valid (see Note 10) 60 ns 60 ns tdis Disable time from IOR ↑ to DB0 – DB7 released (see Note 10) NOTES: 9. These parameters are not production tested. 10. VOL and VOH (and the external loading) determine the charge and discharge time. 8 MAX POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 transmitter switching characteristics over recommended ranges of operating free-air temperature and supply voltage (see Note 11 and Figures 6, 7, and 8) PARAMETER TEST CONDITIONS MIN MAX UNIT td5 Delay time, interrupt THRE ↓ to SOUT ↓ at start See Figure 6 8 24 RCLK cycles td6 Delay time, SOUT ↓ at start to interrupt THRE ↑ See Note 12 and Figure 6 8 9 RCLK cycles td7 Delay time, IOW (WR THR) ↑ to interrupt THRE ↑ See Note 12 and Figure 6 16 32 RCLK cycles td8 Delay time, SOUT ↓ at start to TXRDY ↓ CL = 100 pF, See Figures 7 and 8 8 RCLK cycles tpd2 Propagation delay time from IOW (WR THR) ↓ to interrupt THRE ↓ CL = 100 pF, See Figure 6 140 ns tpd4 Propagation delay time from IOR (RD IIR) ↑ to interrupt THRE ↓ CL = 100 pF, See Figure 6 140 ns tpd5 Propagation delay time from IOW (WR THR) ↑ to TXRDY ↑ CL = 100 pF, See Figures 7 and 8 195 ns NOTES: 11. These parameters are not production tested. 12. When the transmitter interrupt delay is active, this delay is lengthened by one character time minus the last stop bit time. receiver switching characteristics over recommended ranges of operating free-air temperature and supply voltage (see Note 13 and Figures 9 through 13) PARAMETER td9 Delay time from stop to INT ↑ tpd6 tpd7 Propagation delay time from RCLK ↑ to sample CLK ↑ tpd8 Propagation delay time from IOR (RD RBR) ↓ to RXRDY ↑ TEST CONDITIONS MIN See Note 14 Propagation delay time from IOR (RD RBR/RD LSR) ↓ to reset interrupt ↓ CL = 100 pF MAX UNIT 1 RCLK cycle 100 ns 150 ns 150 ns NOTES: 13. These parameters are not production tested. 14. The receiver data available indicator, the overrun error indicator, the trigger level interrupts, and the active RXRDY indicator are delayed three RCLK cycles in FIFO mode (FCR0 = 1). After the first byte has been received, status indicators (PE, FE, BI) are delayed three RCLK cycles. These indicators are updated immediately for any further bytes received after RDRBR goes active. There are eight RCLK cycle delays for trigger change level interrupts. modem control switching characteristics over recommended ranges of operating free-air temperature and supply voltage, CL = 100 pF (see Note 15 and Figure 14) MAX UNIT tpd9 tpd10 Propagation delay time from IOW (WR MCR) ↑ to RTS (DTR) ↓↑ PARAMETER MIN 100 ns Propagation delay time from modem input (CTS, DSR) ↓↑ to interrupt ↑ 170 ns tpd11 tpd12 Propagation delay time from IOR (RD MSR) ↑ to interrupt ↓ 140 ns Propagation delay time from RI ↑ to interrupt ↑ 170 ns NOTE 15: These parameters are not production tested. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 9 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 parallel port timing requirements over recommended ranges of supply voltage and operating free-air temperature (see Note 16 and Figures 15, 16, and 17) MIN MAX UNIT tsu7 th6 Setup time, data valid before STB ↓ 1 µs Hold time, data valid after STB ↑ 1 µs tw6 td10 Pulse duration, STB ↓ 1 µs Delay time, BUSY ↑ to ACK ↓ Defined by printer td11 tw7 Delay time, BUSY ↓ to ACK ↓ Defined by printer Pulse duration, BUSY ↑ Defined by printer tw8 td12 Pulse duration, ACK ↓ Defined by printer Delay time, BUSY ↑ after STB ↑ Defined by printer td13 td14 Delay time, INT2 ↓ after ACK ↓ (see Note 17) 22 ns Delay time, INT2 ↑ after ACK ↑ (see Note 17) 20 ns td15 td16 Delay time, INT2 ↑ after ACK ↑ (see Note 17) 24 ns Delay time, INT2 ↓ after IOR ↑ (see Note 17) 25 ns NOTES: 16. These parameters are not production tested. 17. td13 – td16 are all measured with a 15-pF load. PARAMETER MEASUREMENT INFORMATION tw1 2V 2V CLK (XTAL1) 0.8 V 0.8 V tw2 fclock = 16 MHz MAX Figure 1. CLK Voltage Waveform 2.54 V Device Under Test 680 Ω TL16C552A 82 pF (see Note A) NOTE A: This includes scope and jig capacitance. Figure 2. Output Load Circuit 10 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 PARAMETER MEASUREMENT INFORMATION TL16C552A Data Bus Serial Channel 1 Buffers 9-Pin D Connector Serial Channel 2 Buffers 9-Pin D Connector Address Bus Dual ACE and Printer Port Control Bus Option Jumpers Parallel Port R/C Network 25-Pin D Connector Figure 3. Basic Test Configuration A2, A1, A0 Valid 50% 50% th1 CS0, CS1, CS2 Valid 50% 50% tsu1 th2 td1 tsu2 IOR 50% Active 50% 50% td2 tw4 IOW or 50% Active tpd1 tpd1 BDO Active 50% 50% tdis ten DB0 – DB7 Valid Data Figure 4. Read Cycle Timing Waveforms POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 11 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 PARAMETER MEASUREMENT INFORMATION Valid 50% A2, A1, A0 50% th3 CS0, CS1, CS2 Valid 50% 50% tsu4 th4 td3 tsu5 50% Active IOW 50% 50% Active td4 tw5 or IOR Active 50% tsu6 th5 DB0 – DB7 Valid Data Figure 5. Write Cycle Timing Waveforms Start Serial Out (SOUT) 50% Data Bits 5 – 8 Stop (1– 2) Parity td5 Interrupt (THRE) Start 50% 50% 50% td6 50% 50% 50% tpd2 td7 IOW (WR THR) 50% tpd2 50% 50% tpd4 IOR (RD IIR) 50% Figure 6. Transmitter Timing Waveforms IOW (WR THR) SOUT Byte #1 50% Data Parity Stop td8 tpd5 TXRDY Start 50% 50% 50% Figure 7. Transmitter Ready Mode 0 Timing Waveforms 12 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 PARAMETER MEASUREMENT INFORMATION IOW (WR THR) Byte #16 50% Start of Byte #16 SOUT Data Parity Start Stop tpd5 TXRDY td8 50% FIFO Full 50% Figure 8. Transmitter Ready Mode 1 Timing Waveforms RCLK tpd6 8 CLK Cycles CLK TL16C450 Mode SIN (receiver input data) Start Data Bits 5 – 8 Parity Stop Sample CLK td9 Interrupt (data ready or RCVR ERR) 50% 50% tpd7 IOR 50% Active Figure 9. Receiver Timing Waveforms POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 13 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 PARAMETER MEASUREMENT INFORMATION SIN Start Data Bits 5 – 8 Parity Stop Sample CLK Trigger Interrupt (FCR6, 7 = 0, 0) (FIFO at or above trigger level) 50% 50% td9 (FIFO below trigger level) tpd7 IOR (RD RBR) 50% 50% LSI Interrupt Active 50% tpd7 Active IOR (RD LSR) 50% Figure 10. Receiver FIFO First Byte (Sets RDR) Waveforms SIN Stop Sample CLK Time Out or Trigger Level Interrupt td9 (see Note A) (FIFO at or above trigger level) 50% 50% tpd7 LSI Interrupt 50% Top Byte of FIFO IOR (RD LSR) Active Active 50% tpd7 td9 IOR (RD RBR) (FIFO below trigger level) 50% 50% 50% Active Previous Byte Read From FIFO NOTE A: This is the reading of the last byte in the FIFO. Figure 11. Receiver FIFO After First Byte (After RDR Set) Waveforms 14 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 PARAMETER MEASUREMENT INFORMATION IOR (RD RBR) Active 50% (see Note A) SIN (first byte) Stop Sample CLK RXRDY td9 (see Note B ) tpd8 50% 50% NOTES: A. This is the reading of the last byte in the FIFO. B. If FCR0 = 1, td9 = 3 RCLK cycles. For a time-out interrupt, td9 = 8 RCLK cycles. Figure 12. Receiver Ready Mode 0 Waveforms IOR (RD RBR) 50% Active (see Note A) SIN (first byte that reaches the trigger level) Stop Sample CLK td9 (see Note B) RXRDY 50% 50% tpd8 NOTES: A. This is the reading of the last byte in the FIFO. B. If FCR0 –1, td9 = 3 RCLK cycles. For a trigger change level interrupt, td9 = 8 RCLK. Figure 13. Receiver Ready Mode 1 Waveforms POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 15 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 PARAMETER MEASUREMENT INFORMATION IOW (WR MCR) 50% 50% tpd9 tpd9 50% RTS, DTR CTS, DSR, DCD 50% 50% 50% tpd10 INT0, INT1, 1 INT, 2 INT tpd10 50% 50% 50% 50% tpd11 IOR (RD MSR) tpd12 50% 50% RI Figure 14. Modem Control Timing Waveforms DATA Valid 50% 50% tsu7 STB th6 50% 50% tw6 50% ACK BUSY ÉÉÉÉÉ ÉÉÉÉÉ 50% td12 50% td10 tw8 td11 50% 50% tw7 Figure 15. Parallel Port Timing Waveforms 16 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 PARAMETER MEASUREMENT INFORMATION ENIRQ ACK 50% 50% td14 td13 50% INT2 50% Line Printer Status Register, Bit 2 (PRINT) 50% td(int (see Note A) IOR (RD_LPS) 50% NOTE A: A timing value is not provided for td(int) in the tables because the line printer status register, bit 2 (PRINT) is an internal signal. Figure 16. Parallel Port AT Mode Timing (ENIRQ = Low) Waveforms ENIRQ 50% ACK td16 td15 50% 50% INT2 PRINT IOR (RD_LPS) 50% Figure 17. Parallel Port PS/2 Mode Timing (ENIRQ = High) Waveforms RESET 50% 50% tw3 Figure 18. RESET Voltage Waveform POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 17 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 PRINCIPLES OF OPERATION Three types of information are stored in the internal registers used in the ACE: control, status, and data. Mnemonic abbreviations for the internal registers are shown in Table 1. Table 1. Internal Register Mnemonic Abbreviations CONTROL MNEMONIC Line control register STATUS MNEMONIC DATA MNEMONIC LCR Line status register LSR Receiver buffer register RBR FIFO control register FCR Modem status register MSR Transmitter holding register THR Modem control register MCR Divisor latch LSB DLL Divisor latch MSB DLM Interrupt enable register IER The address, read, and write inputs are used with the divisor latch access bit (DLAB) in the line control register (bit 7) to select the register to be written to or read from (see Table 2). Individual bits within the registers are referred to by the register mnemonic and the bit number in parenthesis. As an example, LCR7 refers to line control register bit 7. The transmitter holding register and receiver buffer register are data registers that hold from five to eight bits of data. If fewer than eight data bits are transmitted, data is right justified to the LSB. Bit 0 of a data word is always the first serial data bit received and transmitted. The ACE data registers are double buffered (TL16C450 mode) or FIFO buffered (FIFO mode) so that read and write operations can be performed when the ACE is performing the parallel-to-serial or serial-to-parallel conversion. Table 2. Register Selection† DLAB A2 A1 A0 MNEMONIC L L REGISTER L L L RBR Receiver buffer register (read only) L L L THR Transmitter holding register (write only) L L L H IER Interrupt enable register X L H L IIR Interrupt identification register (read only) X L H L FCR FIFO control register (write only) X L H H LCR Line control register X H L L MCR Modem control register X H L H LSR Line status register X H H L MSR Modem status register X H H H SCR Scratch pad register H L L L DLL LSB divisor latch H L L H DLM MSB divisor latch † The serial channel is accessed when either CS0 or CS1 is low. X = irrelevant, L = low level, H = high level 18 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 PRINCIPLES OF OPERATION accessible registers Using the CPU, the system programmer has access to and control over any of the ACE registers that are summarized in Table 1. These registers control ACE operations, receive data, and transmit data. Descriptions of these registers follow Table 3. Table 3. Summary of Accessible Registers REGISTER BIT NUMBER REGISTER MNEMONIC BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 0 RBR (read only) Data Bit 7 (MSB) Data Bit 6 Data Bit 5 Data Bit 4 Data Bit 3 Data Bit 2 Data Bit 1 Data Bit 0 (LSB) 0 THR (write only) Data Bit 7 Data Bit 6 Data Bit 5 Data Bit 4 Data Bit 3 Data Bit 2 Data Bit 1 Data Bit 0 Bit 0 ADDRESS 0† DLL Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 1† DLM Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 1 IER 0 0 0 0 (EDSSI) Enable modem status interrupt (ERLSI) Enable receiver line status interrupt (ETBEI) Enable transmitter g holding register g empty interrupt (ERBFI) Enable received data available interrupt 2 FCR (write only) Receiver trigger (MSB) Receiver trigger (LSB) Reserved Reserved DMA mode select Transmitter FIFO reset Receiver FIFO reset FIFO enable 2 IIR (read only) FIFOs enabled‡ FIFOs enabled‡ 0 0 Interrupt ID bit 3‡ Interrupt ID bit 2 Interrupt ID bit 1 0 if interrupt pending 3 LCR ((DLAB)) Divisor latch access bit Set break Stick parity ((EPS)) Even parity select ((PEN)) Parity enable ((STB)) Number of stop bits ((WLSB1)) Word length select bit 1 ((WLSB0)) Word length select bit 0 4 MCR 0 0 0 Loop OUT2 Enable external interrupt (INT0 or INT1) OUT1 (an unused internal signal) i l) (RTS) ( ) Request to send (DTR) ( ) Data terminal ready d 5 LSR Error in receiver FIFO‡ ((TEMT)) Transmitter empty ((THRE)) Transmitter holding register i t empty ((BI)) Break interrupt ((FE)) Framing error ((PE)) Parity error ((OE)) Overrun error ( ) (DR) Data ready 6 MSR (DCD) Data carrier detect (RI) Ring indicator (DSR) Data set ready (CTS) Clear to send (∆ DCD) Delta data carrier detect (TERI) Trailing edge ring indicator (∆ DSR) Delta data set ready (∆ CTS) Delta clear clear to send 7 SCR Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 † DLAB = 1 ‡ These bits are always 0 when FIFOs are disabled. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 19 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 PRINCIPLES OF OPERATION FIFO control register (FCR) This write-only register is at the same location as the interrupt identification register. It enables and clears the FIFOs, sets the trigger level of the receiver FIFO, and selects the type of DMA signaling. D D D D D D Bit 0: FCR0 enables both the transmitter and receiver FIFOs. All bytes in both FIFOs can be cleared by clearing FCR0. Data is cleared automatically from the FIFOs when changing from the FIFO mode to the TL16C450 mode and vice versa. Programming of other FCR bits is enabled by setting FCR0. Bit 1: When set, FCR1 clears all bytes in the receiver FIFO and resets the counter. This does not clear the shift register. Bit 2: When set, FCR2 clears all bytes in the transmitter FIFO and resets the counter. This does not clear the shift register. Bit 3: When set, FCR3 changes the RXRDY and TXRDY terminals from mode 0 to mode 1 when FCR0 is set. Bits 4 and 5: FCR4 and FCR5 are reserved for future use. Bits 6 and 7: FCR6 and FCR7 set the trigger level for the receiver FIFO interrupt (see Table 4). Table 4. Receiver FIFO Trigger Level 7 6 RECEIVER FIFO TRIGGER LEVEL (BYTES) 0 0 01 0 1 04 1 0 08 1 1 14 BIT FIFO interrupt mode operation The following receiver status occurs when the receiver FIFO and receiver interrupts are enabled: 1. LSR0 is set when a character is transferred from the shift register to the receiver FIFO. When the FIFO is empty, it is reset. 2. IIR = 06 receiver line status interrupt has higher priority than the received data available interrupt IIR = 04. 3. Receive data available interrupt is issued to the CPU when the programmed trigger level is reached by the FIFO. When the FIFO drops below its programmed trigger level, it is cleared. 4. IIR = 04 (receive data available indicator) also occurs when the FIFO reaches its trigger level. It is cleared when the FIFO drops below the programmed trigger level. The following receiver FIFO character time-out status occurs when receiver FIFO and receiver interrupts are enabled. 20 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 PRINCIPLES OF OPERATION FIFO interrupt mode operation (continued) 1. When the following conditions exist, a FIFO character time-out interrupt occurs: a. Minimum of one character in FIFO b. The last received serial character is longer than four previous continuous-character times (if two stop bits are programmed, the second one is included in the time delay). c. The last CPU read of the FIFO is more than four previous continuous-character times. At 300 baud and 12-bit characters, the FIFO time-out interrupt causes a latency of 160 ms maximum from received character to interrupt issued.1 2. By using the RCLK input for a clock signal, the character times can be calculated. The delay is proportional to the baud rate. 3. The time-out timer is reset after the CPU reads the receiver FIFO or after a new character is received when there has been no time-out interrupt. 4. A time-out interrupt is cleared and the timer is reset when the CPU reads a character from the receiver FIFO. Transmitter interrupts occur as follows when the transmitter and transmitter FIFO interrupts are enabled (FCR0 = 1, IER = 1). 1. When the transmitter FIFO is empty, the transmitter holding register interrupt (IIR = 02) occurs. The interrupt is cleared when the transmitter holding register is written to or the IIR is read. One to sixteen characters can be written to the transmit FIFO when servicing this interrupt. 2. The transmitter FIFO empty indicators are delayed one character time minus the last stop bit time when the following occurs: THRE = 1 and there is not a minimum of two bytes at the same time in transmitter FIFO since the last THRE = 1. The first transmitter interrupt after changing FCR0 is immediate, assuming it is enabled. Receiver FIFO trigger level and character time-out interrupts have the same priority as the received data available interrupt. The transmitter holding register empty interrupt has the same priority as the transmitter FIFO empty interrupt. FIFO polled mode operation Clearing IER0, IER1, IER2, IER3, or all with FCR0 = 1 puts the ACE into the FIFO polled mode. The receiver and transmitter are controlled separately. Either one or both can be in the polled mode. In the FIFO polled mode, there is no time-out condition indicated or trigger level reached. However, the receiver and transmitter FIFOs still have the capability of holding characters. The LSR must be read to determine the ACE status. interrupt enable register (IER) The IER independently enables the four serial channel interrupt sources that activate the interrupt (INT0 or INT1) output. All interrupts are disabled by clearing IER0 – IER3. Interrupts are enabled by setting the appropriate bits of the IER. Disabling the interrupt system inhibits the interrupt identification register and the active (high) interrupt output. All other system functions operate in their normal manner, including the setting of the LSRs and MSRs. The contents of the IER shown in Table 3 are described in the following bulleted list. D Bit 0: When IER0 is set, IER0 enables the received data available interrupt and the time-out interrupts in the FIFO mode. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 21 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 PRINCIPLES OF OPERATION interrupt enable register (IER) (continued) D D D D Bit 1: When IER1 is set, the transmitter holding register empty interrupt is enabled. Bit 2: When IER2 is set, the receiver line status interrupt is enabled. Bit 3: When IER3 is set, the modem status interrupt is enabled. Bits 4 – 7: IER4 through IER7 are cleared. In order to minimize software overhead during data character transfers, the serial channel prioritizes interrupts into four levels. The four levels of interrupt conditions are as follows: D D D D Priority 1 – Receiver line status (highest priority) Priority 2 – Receiver data ready or receiver character time out Priority 3 – Transmitter holding register empty Priority 4 – Modem status (lowest priority) Information indicating that a prioritized interrupt is pending and the type of interrupt is stored in the IIR. The IIR indicates the highest priority interrupt pending. The contents of the IIR are indicated in Table 5. Table 5. Interrupt Control Functions INTERRUPT IDENTIFICATION REGISTER INTERRUPT SET AND RESET FUNCTIONS BIT 3 BIT 2 BIT 1 BIT 0 PRIORITY LEVEL 0 0 0 1 None None None None 0 1 1 0 First Receiver line status OE, PE, FE, or BI LSR read 0 1 0 0 Second Received data available Receiver data available or trigger level reached RBR read until FIFO drops below the trigger level 1 1 0 0 Second Character time-out indicator No characters have been removed from or input to the receiver FIFO during the last four character times and there is at least one character in it during this time. RBR read 0 0 1 0 Third THRE THRE IIR read if THRE is the interrupt source or THR write 0 0 0 0 Fourth Modem status CTS, DSR, RI, or DCD MSR read D D D D D 22 INTERRUPT TYPE INTERRUPT SOURCE INTERRUPT RESET CONTROL Bit 0: IIR0 indicates whether an interrupt is pending. When IIR0 is cleared, an interrupt is pending. Bits 1 and 2: IIR1 and IIR2 identify the highest priority interrupt pending, as indicated in Table 5. Bit 3: IIR3 is always cleared in TL16C450 mode. This bit is set along with bit 2 in FIFO mode and when a trigger change level interrupt is pending. Bits 4 and 5: IIR4 and IIR5 are always cleared. Bits 6 and 7: IIR6 and IIR7 are set when FCR0 = 1. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 PRINCIPLES OF OPERATION line control register (LCR) The format of the data character is controlled by the LCR. The LCR can be read. Its contents are described in the following bulleted list and shown in Figure 19. D D D D D D Bits 0 and 1: LCR0 and LCR1 are the word length select bits. The number of bits in each serial character is programmed as shown. Bit 2: LCR2 is the stop bit select bit. LCR2 specifies the number of stop bits in each transmitted character. The receiver always checks for one stop bit. Bit 3: LCR3 is the parity enable bit. When LCR3 is set, a parity bit between the last data word bit and stop bit is generated and checked. Bit 4: LCR4 is the even parity select bit. When LCR4 is set, even parity is enabled. Bit 5: LCR5 is the stick parity bit. When parity is enabled (LCR3 = 1), LCR5 = 1 causes the transmission and reception of a parity bit to be in the opposite state from the value of LCR4. This forces parity to a known state and allows the receiver to check the parity bit in a known state. Bit 6: LCR6 is the break control bit. When LCR6 is set, the serial output (SOUT1/SOUT0) is forced to the spacing state (low). The break control bit acts only on the serial output and does not affect the transmitter logic. When the following sequence is used, no invalid characters are transmitted because of the break: Step 1: Load a zero byte in response to the transmitter holding register empty (THRE) status indicator. Step 2: Set the break in response to the next THRE status indicator. Step 3: Wait for the transmitter to be idle when transmitter empty status signal is set high (TEMT = 1); then clear the break when the normal transmission has to be restored. D Bit 7: LCR7 is the divisor latch access bit (DLAB) bit. LCR7 must be set to access the divisor latches DLL and DLM of the baud rate generator during a read or write operation. LCR7 must be cleared to access the receiver buffer register, the transmitter holding register, or the interrupt enable register. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 23 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 PRINCIPLES OF OPERATION line control register (LCR) (continued) Line Control Register LCR LCR LCR LCR LCR LCR LCR LCR 7 6 5 4 3 2 1 0 Word Length Select 0 0 1 1 0 = 5 Data Bits 1 = 6 Data Bits 0 = 7 Data Bits 1 = 8 Data Bits Stop Bit Select 0 = 1 Stop Bits 1 = 1.5 Stop Bits if 5 Data Bits Selected 2 Stop Bits if 6, 7, 8 Data Bits Selected Parity Enable 0 = Parity Disabled 1 = Parity Enabled Even Parity Select 0 = Odd Parity 1 = Even Parity Stick Parity 0 = Stick Parity Disabled 1 = Stick Parity Enabled Break Control 0 = Break Disabled 1 = Break Enabled Divisor Latch Access Bit 0 = Access Receiver Buffer 1 = Access Divisor Latches Figure 19. Line Control Register Contents line printer port The line printer port contains the functionality of the port included in the TL16C452 but offers a hardware programmable extended mode controlled by the printer enhancement mode (PE) terminal. This enhancement is the addition of a direction control bit and an interrupt status bit. register 0 line printer data register The line printer (LPT) port is either output only or bidirectional depending on the state of the extended mode terminal and data direction control bits. Compatibility mode (PEMD = L) Reads to the LPT data register and returns the last data that was written to the port. Write operations immediately output data to PD0 – PD7. Extended mode (PEMD = H) Read operations return either the data last written to the LPT data register when the direction bit is cleared or return the data that is present on PD0 – PD7 when the direction is set to read. Write operations to the LPT data register latch data into the output register; however, they only drive the LPT port when the direction bit is cleared. 24 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 PRINCIPLES OF OPERATION line printer port (continued) Table 6 summarizes the configuration of the PD port based on the combinations of the logic level on the PEMD terminal and the value of the direction control bit (DIR). Table 6. Extended Mode and Direction Control Bit Combinations PEMD DIR PD0 – PD7 FUNCTION L X PC/AT mode – output H 0 PS/2 mode – output H 1 PS/2 mode – input register 1 read line printer status register The line printer status (LPS) register is a read-only register that contains interrupt and printer status of the LPT connector terminals. Table 7 (in the default column) shows the values of each bit after reset in the case of the printer being disconnected from the port. Table 7. LPS Register Bit Description BIT DESCRIPTION DEFAULT 0 Reserved 1 1 Reserved 1 2 PRINT 1 3 ERR † 4 SLCT † 5 PE † 6 ACK † 7 BSY † Outputs are dependent upon device inputs. D D D D D D D † Bits 0 and 1: LPS0 and LPS1 are reserved and always set. Bit 2: LPS2 is the printer interrupt (PRINT, active low) status bit. When cleared, LPS2 indicates that the printer has acknowledged the previous transfer with an ACK handshake (if bit 4 of the control register is set). The bit is cleared on the active-to-inactive transition of the ACK signal. This bit is set after a read of the status port. Bit 3: ERR is the error status bit and corresponds to ERR input. Bit 4: SLCT is the select status bit and corresponds to SLCT input. Bit 5: PE is the paper empty status bit and corresponds to PE input. Bit 6: ACK is the acknowledge status bit corresponds to ACK input. Bit 7: BSY is the busy status bit and corresponds to BUSY input (active high). POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 25 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 PRINCIPLES OF OPERATION register 2 line printer control register The line printer control (LPC) register is a read/write port that controls the PD0 – PD7 direction and drives the printer control lines. Write operations set or clear these bits, whereas read operations return the state of the last write operation to this register. The bits in this register are defined in Table 8 and the following bulleted list. Table 8. LPC Register Bit Description BIT D D D D D D D 26 DESCRIPTION 0 STB 1 AFD 2 INIT 3 SLIN 4 INT2 EN 5 DIR 6 Reserved 0 7 Reserved 0 Bit 0: STB is the printer strobe control bit. When STB is set, the STB signal is asserted on the LPT interface. When STB is cleared, the STB signal is negated. Bit 1: AFD is the autofeed control bit. When AFD is set, the AFD signal is asserted on the LPT interface. When AFD is cleared, the signal is negated. Bit 2: INIT is the initialize printer control bit. When INIT is set, the INIT signal is negated. When INIT is cleared, the INIT signal is asserted on the LPT interface. Bit 3: SLIN is the select input control bit. When SLIN is set, the SLIN signal is asserted on the LPT interface. When SLIN is cleared, the signal is negated. Bit 4: INT2 EN is the interrupt request enable control bit. When set, INT2 EN enables interrupts from the LPT port. When cleared, INT2 EN disables interrupts and places INT2 signal in the high-impedance state. Bit 5: DIR is the direction control bit which is only used when PEMD is high. When DIR is set, the output buffers in the LPD port are disableded to allow data driven from external sources to be read from the LPD port. When DIR is cleared, the LPD port is in the output mode. Bits 6 and 7: These bits are reserved and are always cleared. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 PRINCIPLES OF OPERATION line status register (LSR) The LSR is a single register that provides status indicators. The LSR bits shown in Table 9 are described in the following bulleted list. D D D D D Bit 0: DR is the data ready bit. When set, an incoming character is received and transferred into the receiver buffer register or in the FIFO. LSR0 is cleared by a CPU read of the data in the receiver buffer register or in the FIFO. Bit 1: OE is the overrun error bit. An OE indicates that data in the receiver buffer register is not read by the CPU before the next character is transferred into the receiver buffer register overwriting the previous character. The OE indicator is cleared whenever the CPU reads the contents of the LSR. An overrun error occurs in FIFO mode after the FIFO is full and the next character is completely received. The overrun error is detected by the CPU on the first LSR read after it happens. The character in the shift register is not transferred to the FIFO, but it is overwritten. Bit 2: PE is the parity error bit. A PE indicates that the received data character does not have the correct parity as selected by LCR3 and LCR4. The PE bit is set upon detection of a parity error and is cleared when the CPU reads the contents of the LSR. In FIFO mode, the parity error is associated with a particular character in the FIFO. LSR2 reflects the error when the character is at the top of the FIFO. Bit 3: FE is the framing error bit. An FE indicates that the received character does not have a valid stop bit. LSR3 is set when the stop bit following the last data bit or parity bit is detected as a zero bit (spacing level). The FE indicator is cleared when the CPU reads the contents of the LSR. In FIFO mode, the framing error is associated with a particular character in the FIFO. LSR3 reflects the error when the character is at the top of the FIFO. Bit 4: BI is the break interrupt bit. BI is set when the received data input is held in the spacing (low) state for longer than a full word transmission time (start bit + data bits + parity + stop bits). The BI indicator is cleared when the CPU reads the contents of the LSR. In FIFO mode, this is associated with a particular character in the FIFO. LSR4 reflects BI when the break character is at the top of the FIFO. The error is detected by the CPU when its associated character is at the top of the FIFO during the first LSR read. Only one zero character is loaded into the FIFO when BI occurs. LSR1 – LSR4 are the error conditions that produce a receiver line status interrupt (priority 1 interrupt in the interrupt identification register) when any of the conditions are detected. This interrupt is enabled by setting IER2 in the interrupt enable register. D D D Bit 5: THRE is the transmitter holding register empty bit. THRE indicates that the ACE is ready to accept a new character for transmission. The THRE bit is set when a character is transferred from the transmitter holding register into the transmitter shift register. LSR5 is cleared by the loading of the transmitter holding register by the CPU. LSR5 is not cleared by a CPU read of the LSR. In FIFO mode when the transmitter FIFO is empty, this bit is set. It is cleared when one byte is written to the transmitter FIFO. When the THRE interrupt is enabled by IER1, THRE causes a priority 3 interrupt in the IIR. If THRE is the interrupt source indicated in IIR, INTRPT is cleared by a read of the IIR. Bit 6: TEMT is the transmitter empty bit. TEMT is set when the transmitter holding register (THR) and the transmitter shift register are both empty. LSR6 is cleared when a character is loaded into the THR and remains cleared until the character is transferred out of SOUT. TEMT is not cleared by a CPU read of the LSR. In FIFO mode, when both the transmitter FIFO and shift register are empty, TEMT is set. Bit 7: LSR7 is the receiver FIFO error bit. The LSR7 bit is always cleared in TL16C450 mode. In FIFO mode, it is set when at least one of the following data errors occurs in the FIFO: parity error, framing error, or break interrupt indicator. It is cleared when the CPU reads the LSR if there are no subsequent errors in the FIFO. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 27 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 PRINCIPLES OF OPERATION line status register (LSR) (continued) NOTE: The LSR may be written to. However, this function is intended only for factory test. It should be considered as read only by applications software. Table 9. Line Status Register Bits LSR BITS 1 0 Ready Not ready LSR1 overrun error (OE) Error No error LSR2 parity error (PE) Error No error LSR3 framing error (FE) Error No error LSR0 data ready (DR) LSR4 break interrupt (BI) Break No break LSR5 transmitter holding register empty (THRE) Empty Not empty LSR6 transmitter empty (TEMT) Empty Not empty Error in FIFO No error in FIFO LSR7 receiver FIFO error master reset After power up, the ACE RESET input should be held low for one microsecond to reset the ACE circuits to an idle mode until initialization. A low on RESET causes the following: D D It initializes the transmitter and receiver clock counters. It clears the LSR except for transmitter shift register empty (TEMT) and transmit holding register empty (THRE), which are set. The MCR is also cleared. All of the discrete lines, memory elements, and miscellaneous logic associated with these register bits are also cleared or turned off. The LCR, divisor latches, receiver buffer register, and transmitter holding buffer register are not affected. Following the removal of the reset condition (RESET high), the ACE remains in idle mode until programmed. A hardware reset of the ACE sets the THRE and TEMT status bit in the LSR. When interrupts are subsequently enabled, an interrupt occurs due to THRE. A summary of the effect of a reset on the ACE is given in Table 10. 28 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 PRINCIPLES OF OPERATION master reset (continued) Table 10. RESET Effects on Registers and Signals REGISTER/SIGNAL RESET CONTROL RESET Interrupt enable register Reset All bits cleared (0 – 3 forced and 4 – 7 permanent) Interrupt identification register Reset Bit 0 is set,, bits 1,, 2,, 3,, 6,, and 7 are cleared,, and bits 4 – 5 are permanentlyy cleared. Line control register Reset All bits are cleared. Modem control register Reset All bits are cleared (5 – 7 permanently). FIFO control register Reset All bits are cleared. Line status register Reset All bits are cleared, except bits 5 and 6 are set. Modem status register Reset Bits 0 – 3 are cleared, bits 4 – 7 input signal. SOUT Reset High Interrupt (RCVR errors) Read LSR/Reset Low Interrupt (receiver data ready) Read RBR/Reset Low Read IIR/Write THR/Reset Low Interrupt (THRE) Interrupt (modem status changes) Read MSR/Reset Low OUT2 Reset High RTS Reset High DTR Reset High OUT1 Reset High modem control register (MCR) The MCR controls the interface with the modem or data set as described in Figure 20. MCR can be written to and read from. The RTS and DTR outputs are directly controlled by their control bits in this register. A high input asserts a low signal (active) at the output terminals. The MCR bits are defined in the following bulleted list. D D D D D Bit 0: When MCR0 is set, the DTR output is forced low. When MCR0 is cleared, the DTR output is forced high. The DTR output of the serial channel can be input into an inverting line driver in order to obtain the proper polarity input at the modem or data set. Bit 1: When MCR1 is set, the RTS output is forced low. When MCR1 is cleared, the RTS output is forced high. The RTS output of the serial channel can be input into an inverting line driver to obtain the proper polarity input at the modem or data set. Bit 2: MCR2 has no effect on operation. Bit 3: When MCR3 is set, the external serial channel interrupt is enabled. Bit 4: MCR4 provides a local loopback feature for diagnostic testing of the channel. When MCR4 is set, SOUT is set to the marking (high) state and the SIN is disconnected. The output of the transmitter shift register is looped back into the receiver shift register input. The four modem control inputs (CTS, DSR, DCD, and RI) are disconnected. The modem control outputs (DTR, RTS, OUT1, and OUT2) are internally connected to the four modem control inputs. The modem control output terminals are forced to their inactive (high) state on the TL16C552A. In the diagnostic mode, data transmitted is immediately received. This allows the processor to verify the transmit and receive data paths of the selected serial channel. Interrupt control is fully operational; however, interrupts are generated by controlling the lower four MCR bits internally. Interrupts are not generated by activity on the external terminals represented by those four bits. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 29 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 PRINCIPLES OF OPERATION modem control register (MCR) (continued) D Bits 5 – 7: MCR5 – MCR7 are permanently cleared. Modem Control Register MCR MCR MCR MCR MCR MCR MCR MCR 7 6 5 4 3 2 1 0 Data Terminal Ready 0 = DTR Output High (inactive) 1 = DTR Output Low (active) Request to Send 0 = RTS Output High (inactive) 1 = RTS Output Low (active) Out 1 (internal) No Effect on External Operation Out 2 (internal) 0 = External Interrupt Disabled 1 = External Interrupt Enabled Loop 0 = Loop Disabled 1 = Loop Enabled Bits Are Cleared Figure 20. Modem Control Register Contents modem status register (MSR) The MSR provides the CPU with status of the modem input lines from the modem or peripheral devices. The MSR allows the CPU to read the serial channel modem signal inputs. This is done by accessing the data bus interface of the ACE in addition to the current status of four bits of the MSR. These four bits indicate whether the modem inputs have changed since the last reading of the MSR. The delta status bits are set when a control input from the modem changes state and are cleared when the CPU reads the MSR. The modem input lines are CTS, DSR, RI, and DCD. MSR4 – MSR7 are status indicators of these lines. A set status bit indicates that the input is low. A cleared status bit indicates that the input is high. When the modem status interrupt in the interrupt enable register is enabled (IER3), an interrupt is generated whenever MSR0 – MSR3 is set. The MSR is a priority-4 interrupt. The contents of the MSR are described in Table 11. D Bit 0: MSR0 is the delta clear-to-send (∆ CTS) bit. ∆ CTS displays that the CTS input to the serial channel has changed states since it was last read by the CPU. D Bit 1: MSR1 is the delta data set ready (∆ DSR) bit. ∆ DSR indicates that the DSR input to the serial channel has changed states since the last time it was read by the CPU. D 30 Bit 2: MSR2 is the trailing edge of the ring indicator (TERI) bit. TERI indicates that the RI input to the serial channel has changed states from low to high since the last time it was read by the CPU. High-to-low transitions on RI do not activate TERI. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 PRINCIPLES OF OPERATION modem status register (MSR) (continued) D D D D D Bit 3: MSR3 is the delta data carrier detect (∆ DCD) bit. ∆ DCD indicates that the DCD input to the serial channel has changed states since the last time it was read by the CPU. Bit 4: MSR4 is the clear-to-send (CTS) bit. CTS is the complement of the CTS input from the modem that indicates to the serial channel that the modem is ready to receive data from SOUT. When the serial channel is in the loop mode (MCR4 is set), MSR4 reflects the value of RTS in the MCR. Bit 5: MSR5 is the data set ready (DSR) bit. DSR is the complement of the DSR input from the modem to the serial channel that indicates that the modem is ready to provide received data to the serial channel receiver circuitry. When the channel is in loop mode (MCR4 is set), MSR5 reflects the value of DTR in the MCR. Bit 6: MSR6 is the ring indicator (RI) bit. RI is the complement of the RI input. When the channel is in loop mode (MCR4 is set), MSR6 reflects the value of OUT1 in the MCR. Bit 7: MSR7 is the data carrier detect (DCD) bit. Data carrier detect indicates the status of the data carrier detect (DCD) input. When the channel is in loop mode (MCR4 is set), MSR7 reflects the value of OUT2 in the MCR. Reading the MSR register clears the delta modem status indicators but has no effect on the other status bits. For LSR and MSR, the setting of status bits is inhibited during status register read operations. If a status condition is generated during a read IOR operation, the status bit is not set until the trailing edge of the read. When a status bit is set during a read operation and the same status condition occurs, that status bit is cleared at the trailing edge of the read instead of being set again. In loop back mode, when modem status interrupts are enabled, the CTS, DSR, RI and DCD input terminals are ignored; however, a modem status interrupt can still be generated by writing to MCR3 – MCR0. Applications software should not write to the MSR. Table 11. Modem Status Register Bits MSR BIT MNEMONIC MSR0 ∆CTS Delta clear to send MSR1 ∆DSR Delta data set ready MSR2 TERI Trailing edge of ring indicator MSR3 ∆DCD Delta data carrier detect MSR4 CTS Clear to send MSR5 DSR Data set ready MSR6 RI Ring indicator MSR7 DCD POST OFFICE BOX 655303 DESCRIPTION Data carrier detect • DALLAS, TEXAS 75265 31 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 PRINCIPLES OF OPERATION parallel port registers The TL16C552A parallel port can connect the device to a Centronic-style printer interface. When chip select 2 (CS2) is low, the parallel port is selected. Table 12 shows the registers associated with this parallel port. The read or write function of the register is controlled by the state of the read (IOR) and write (IOW) terminals as shown. The read data register allows the microprocessor to read the information on the parallel bus. The read status register allows the microprocessor to read the status of the printer in the six most significant bits. The status bits are printer busy BSY, acknowledge (ACK) (a handshake function), paper empty (PE), printer selected (SLCT), error (ERR), and printer interrupt (PRINT). The read control register allows the state of the control lines to be read. The write control register sets the state of the control lines. They are direction (DIR), interrupt enable (INT2 EN), select in (SLIN), initialize the printer (INIT), autofeed the paper (AFD), and strobe (STB), which informs the printer of the presence of a valid byte on the parallel bus. The write data register allows the microprocessor to write a byte to the parallel bus. The parallel port is completely compatible with the parallel port implementation used in the IBM serial parallel adapter. Table 12. Parallel Port Registers REGISTER REGISTER BITS BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 Read data PD7 PD6 PD5 PD4 PD3 PD2 PD1 PD0 Read status BSY ACK PE SLCT ERR PRINT 1 1 Read control 0 0 PEMD • DIR INT2 EN SLIN INIT AFD STB PD7 PD6 PD5 PD4 PD3 PD2 PD1 PD0 0 0 DIR INT2 EN SLIN INIT AFD STB Write data Write control Table 13. Parallel Port Register Select CONTROL PINS A0 REGISTER SELECTED IOR IOW CS2 A1 L H L L L Read data L H L L H Read status L H L H L Read control L H L H H Invalid H L L L L Write data H L L L H Invalid H L L H L Write control H L L H H Invalid programmable baud rate generator The ACE serial channel contains a programmable baud rate generator (BRG) that divides the clock (dc to 8 MHz) by any divisor from 1 to (216 – 1). The output frequency of the baud generator is 16x the data rate [divisor # = clock ÷ (baud rate x 16)], referred to in this document as RCLK. Two 8-bit divisor latch registers store the divisor in a 16-bit binary format. These divisor latch registers must be loaded during initialization. Upon loading either of the divisor latches, a 16-bit baud counter is immediately loaded. This prevents long counts on initial load. The BRG can use any of three different popular frequencies to provide standard baud rates. These frequencies are 1.8432 MHz, 3.072 MHz, and 8 MHz. With these frequencies, standard bit rates from 50 to 512 kbps are available. Tables 14, 15, 16, and 17 illustrate the divisors needed to obtain standard rates using these three frequencies. 32 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 PRINCIPLES OF OPERATION programmable baud rate generator (continued) Table 14. Baud Rates Using a 1.8432-MHz Crystal BAUD RATE DESIRED 50 75 110 134.5 150 300 600 1200 1800 2000 2400 3600 4800 7200 9600 19200 38400 56000 DIVISOR (N) USED TO GENERATE 16x CLOCK PERCENT ERROR DIFFERENCE BETWEEN DESIRED AND ACTUAL 2304 1536 1047 857 768 384 192 96 64 58 48 32 24 16 12 6 3 2 – – 0.026 0.058 – – – – – 0.690 – – – – – – – 2.860 Table 15. Baud Rates Using a 3.072-MHz Crystal BAUD RATE DESIRED 50 75 110 134.5 150 300 600 1200 1800 2000 2400 3600 4800 7200 9600 19200 38400 DIVISOR (N) USED TO GENERATE 16x CLOCK PERCENT ERROR DIFFERENCE BETWEEN DESIRED AND ACTUAL 3840 2560 1745 1428 1280 640 320 160 107 96 80 53 40 27 20 10 5 – – 0.026 0.034 – – – – 0.312 – – 0.628 – 1.230 – – – POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 33 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 PRINCIPLES OF OPERATION programmable baud rate generator (continued) Table 16. Baud Rates Using an 8-MHz Clock BAUD RATE DESIRED 50 75 110 134.5 150 300 600 1200 1800 2000 2400 3600 4800 7200 9600 19200 38400 56000 128000 256000 512000 DIVISOR (N) USED TO GENERATE 16x CLOCK PERCENT ERROR DIFFERENCE BETWEEN DESIRED AND ACTUAL 10000 6667 4545 3717 3333 1667 833 417 277 250 208 139 104 69 52 26 13 9 4 2 1 – 0.005 0.010 0.013 0.010 0.020 0.040 0.080 0.080 – 0.160 0.080 0.160 0.644 0.160 0.160 0.160 0.790 2.344 2.344 2.400 Table 17. Baud Rates Using a 16-MHz Clock 34 BAUD RATE DESIRED DIVISOR (N) USED TO GENERATE 16x CLOCK 50 75 110 134.5 150 300 600 1200 1800 2000 2400 3600 4800 7200 9600 19200 38400 56000 128000 256000 512000 1000000 20000 13334 9090 7434 6666 3334 1666 834 554 500 416 278 208 138 104 52 26 18 8 4 2 1 POST OFFICE BOX 655303 PERCENT ERROR DIFFERENCE BETWEEN DESIRED AND ACTUAL 0.00 0.00 0.01 0.01 0.01 – 0.02 0.04 – 0.08 0.28 0.00 0.16 – 0.08 0.16 0.64 0.16 0.16 0.16 – 0.79 – 2.34 – 2.34 – 2.34 0.00 • DALLAS, TEXAS 75265 TL16C552A, TL16C552AM DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO SLLS189D – NOVEMBER 1994 – REVISED JANUARY 1999 PRINCIPLES OF OPERATION programming The serial channel of the ACE is programmed by the control registers: LCR, IER, DLL, DLM, MCR, and FCR. These control words define the character length, number of stop bits, parity, baud rate, and modem interface. While the control registers can be written to in any order, the IER should be written to last because it controls the interrupt enables. Once the serial channel is programmed and operational, these registers can be updated any time the ACE serial channel is not transmitting or receiving data. receiver Serial asynchronous data is input into SIN. The ACE continually searches for a high-to-low transition from the idle state. When the transition is detected, a counter is reset and counts the 16 × clock to 7 1/2, which is the center of the start bit. The start bit is valid if SIN is still low. Verifying the start bits prevents the receiver from assembling a false data character due to a low-going noise spike on the SIN input. The LCR determines the number of data bits in a character (LCR0 and LCR1). When parity is used, LCR3 and the polarity of parity LCR4 is needed. Status for the receiver is provided in the LSR. When a full character is received, including parity and stop bits, the data received indicator in LSR0 is set. The CPU reads the receiver buffer register, which clears LSR0. If the character is not read prior to a new character transfer from the RSR to the RBR, the overrun error status indicator is set in LSR1. If there is a parity error, the parity error is set in LSR2. If a stop bit is not detected, a framing error indicator is set in LSR3. If the data into SIN is a symmetrical square wave, the center of the data cells occurs within ± 3.125% of the actual center, providing an error margin of 46.875%. The start bit can begin as much as one 16× clock cycle prior to being detected. scratchpad register The scratch register is an 8-bit read/ write register that has no effect on either channel in the ACE. It is intended to be used by the programmer to hold data temporarily. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 35 PACKAGE OPTION ADDENDUM www.ti.com 17-Mar-2017 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) 5962-9755001QXA ACTIVE CFP HV 68 1 TBD Call TI N / A for Pkg Type -55 to 125 5962-9755001QX A TL16C552AMHVB TL16C552AFN ACTIVE PLCC FN 68 18 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR -40 to 85 TL16C552AFN TL16C552AFNG4 ACTIVE PLCC FN 68 18 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR -40 to 85 TL16C552AFN TL16C552AFNR ACTIVE PLCC FN 68 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR TL16C552AFN TL16C552AFNRG4 ACTIVE PLCC FN 68 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR TL16C552AFN TL16C552AIFN ACTIVE PLCC FN 68 18 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR TL16C552AIFN TL16C552AIFNG4 ACTIVE PLCC FN 68 18 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR TL16C552AIFN TL16C552AMHV ACTIVE CFP HV 68 1 TBD Call TI N / A for Pkg Type -55 to 125 TL16C552AMHV TL16C552AMHVB ACTIVE CFP HV 68 1 TBD Call TI N / A for Pkg Type -55 to 125 5962-9755001QX A TL16C552AMHVB TL16C552APN ACTIVE LQFP PN 80 119 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR -55 to 125 TL16C552APN (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 17-Mar-2017 Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF TL16C552A, TL16C552AM : • Catalog: TL16C552A • Military: TL16C552AM NOTE: Qualified Version Definitions: • Catalog - TI's standard catalog product • Military - QML certified for Military and Defense Applications Addendum-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2017, Texas Instruments Incorporated